Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.
Ce dont vous avez besoin
-
Outil utilisé dans cette étape :Magnetic Project Mat$19.95
-
Dévissez les dix vis suivantes fixant le boîtier inférieur au boîtier supérieur :
-
Deux vis Pentalobe P5 de 2,3 mm
-
Huit vis Pentalobe P5 de 3,0 mm
-
-
-
Retirez le cache en plastique couvrant la carte de contact de la batterie.
-
-
-
-
Saisissez l'interposeur avec une pincette.
-
Soulevez l'interposeur et mettez-le de côté.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use the tip of a spudger to push the iSight camera cable connector straight away from its socket on the logic board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use the flat end of a spudger to pry and disconnect the three antenna cable connectors from the AirPort board.
-
The three cables are coded with black sleeves of different lengths. During reassembly:
-
Connect the long-sleeved cable to the socket closest to the ports.
-
The short-sleeved cable connects next to the screw.
-
The remaining cable has no sleeve, and connects in the last empty socket, next to the fan.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Move the antenna cables aside, clear of the AirPort board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Grab the black pull tab secured to the display data cable lock and rotate it toward the DC-In side of the computer.
-
Pull the display data cable straight out of its socket on the logic board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use a pair of tweezers to lift the rubber hinge covers up off the right and left display hinges.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the two 3.1 mm T5 Torx screws securing the aluminum hinge brackets.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use a pair of tweezers to lift aluminum hinge brackets off the right and left display hinges.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the four inner 5.3 mm T8 Torx screws (two on each side) securing the display to the upper case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
While holding the display and upper case together with your left hand, remove the remaining T8 Torx screw from the upper display bracket.
-
Remove the last remaining T8 Torx screw securing the display to the upper case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Grip both halves of the device, one in each hand.
-
Gently push forward on the bottom half of the device to detach it from the display assembly.
-
Carefully set each component aside, making sure to set down the lower half keyboard-side down.
-
Annulation : je n'ai pas terminé ce tutoriel.
34 autres ont terminé cette réparation.
8 commentaires
This worked really well. The only issue I had was uninstalling the camera. The instructions to pull the data display cable parallel to logic board made sense in step 14. Unfortunately I didn't understand the similarities in step 10. Is it possible to repair the camera now that the slot is completely broken?
Walk through worked perfect. Did it twice. The first time was just to make sure that wasn’t anything disconnect or any wires damage. The second time was to replace the screen. Works perfect.
Hi,
can I replace an damaged display of a MacBook Pro 13” late 2013 with a display from the early 2013 version?
I compared the high-def pictures of each cable connection and they seem to be identical, or am I wrong?
Thanks for the help.
Cheers
L