Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.
Ce dont vous avez besoin
-
-
Poussez avec les doigts les deux loquets de déverrouillage de la batterie et retirez celle-ci de l'ordinateur.
-
-
-
Retirez les trois vis identiques Phillips de 2 mm du capot de la mémoire.
-
Soulevez le capot suffisamment pour le saisir et retirez-le en le faisant glisser vers vous.
-
-
-
Retirez les deux vis Phillips 2,8 mm situées près du loquet, dans le compartiment de la batterie.
-
-
-
Soulevez l'arrière du boîtier et à l'aide de vos doigts, libérez progressivement le boîtier par les côtés en allant de l'arrière vers l'avant. Une fois les côtés du boîtier libérés, vous devrez peut-être bouger le boîtier de bas en haut pour libérer la partie avant.
-
Quatre clips en plastique sont disposés au-dessus du logement du DVD et un autre au-dessus, à gauche du capteur infrarouge. Ces clips peuvent être très difficiles à désengager sans mouvement de levier. Ils peuvent également être difficiles à ré-engager lors du remontage.
-
-
-
Servez-vous de l'extrémité plate d'un spudger pour débrancher le câble-ruban orange du lecteur SuperDrive de la carte mère. Retirez la bande adhésive si nécessaire.
-
-
-
-
Retirez les 4 vis suivantes :
-
Deux vis Phillips 3,3 mm argent de chaque côté du lecteur SuperDrive.
-
Une vis Torx T6 4,7 mm argent dans l'angle supérieur gauche du lecteur.
-
Une vis Phillips T6 6,2 mm noire dans l'angle supérieur droit du lecteur.
-
Retirez le lecteur optique de l'ordinateur en le soulevant.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Disconnect the hard drive and ExpressCard connectors from the left side of the logic board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Disconnect the iSight and display data cables from the logic board by sliding them straight back out of their connectors, removing tape as necessary.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Disconnect the eight indicated connectors by placing a spudger beneath the wired side of each one and lifting up.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the foam bumper from the top of the right hinge of the display.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the silver 9.5 mm T6 Torx screw securing the ground loop in the display data cable to the casing.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the single black 6 mm T6 Torx screw securing the upper portion of the logic board to the lower case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Peel up the orange Kapton tape securing the right thermal sensor cable to the logic board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the following 15 screws:
-
One 4.4 mm black Phillips screw to the right of the ram slot.
-
Eight 4.7 mm silver T6 Torx screws securing the logic board to the lower case.
-
One 6.2 mm black T6 Torx screw on the right side of the left fan.
-
Five 9.4 mm silver T6 Torx screws securing the left and right fans.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Hold the logic board down with one hand and use your other hand to lift the left fan up from its housing. There is a piece of black tape securing the left fan to the heat sink. Carefully peel this tape up from the heat sink as you lift the left fan up.
-
Lift the right fan up and carefully peel up the tape securing the fan to the heat sink as you go.
-
Remove the right fan from the computer.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift up the left side of the logic board and disconnect the gray and black power cable from the bottom of the board.
-
Grasp the logic board at the left side and at the thin section, and rotate the logic board out of the lower case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the heat sink out of the computer.
-
Peel up the left ambient light sensor cable from above the left fan, removing tape as necessary.
-
Remove the left fan from the computer.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Disconnect the two antenna cables attached to the Airport Extreme card.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Deroute the Airport antenna cables from their channel in the left speaker.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the single black T6 Torx screw located just above the Airport Extreme card.
-
Lift the small silver metal retaining bracket up and out of the computer.
-
Lift the Airport Extreme card up and slide it out of its connector.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Peel up the orange hard drive cable from above the ExpressCard cage.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Disconnect the speaker cable from the corner of the left I/O board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Carefully peel up the black adhesive tape securing the speaker cable along the rear edge of the lower case.
-
Continue to free the speaker cable from the black tape until it is free from all three sections of tape.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the single black T6 Torx screw securing the right speaker to the lower case.
-
Use a spudger to pry up the right speaker from the lower case.
-
Remove the speakers from the computer.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the single silver Phillips screw securing the clear plastic shield over the left ambient light sensor.
-
Lift the clear plastic shield off the left ambient light sensor.
-
Use a spudger to pry the left ambient light sensor board out of its housing on the left speaker.
-
Speakers remain.
-
Annulation : je n'ai pas terminé ce tutoriel.
12 autres ont terminé cette réparation.
Un commentaire
I noticed that there were not any actual instructions for the Thermal Paste application as recommended. Other than that the instructions were spot on! - Makes repairs much more affordable when I can do it myself. CERTAINLY invest in the spudger if you don't have one though. There really is no other way you can be careful enough when dealing with the logic board and connections.
One other tip - Print out the instructions - get some clear tape and then tape down each screw to the instructions. That will make it much easier to keep track of where everything is going as well as ensuring you don't lose any of the tiny little screws or get one in the wrong spot.