Introduction

Removing the motherboard is necessary if the motherboard itself or components of the motherboard need to be accessed or replaced.

Pièces

Aucune pièce nécessaire.

  1. Locate the single 1 cm screw on the back of the device (enclosed by a red circle in the image). Using a screwdriver with a Torx 10 hex screw, begin removing the 1cm screw by turning the screwdriver counterclockwise. Remove the screw and set aside.
    • Locate the single 1 cm screw on the back of the device (enclosed by a red circle in the image).

    • Using a screwdriver with a Torx 10 hex screw, begin removing the 1cm screw by turning the screwdriver counterclockwise.

    • Remove the screw and set aside.

  2. Rotate your device 90 degrees to the right so that the bottom of the device is facing you. Locate the two horizontal slots on the bottom of the device. You may need to remove the sticker on the bottom of the device to access these slots.
    • Rotate your device 90 degrees to the right so that the bottom of the device is facing you.

    • Locate the two horizontal slots on the bottom of the device.

    • You may need to remove the sticker on the bottom of the device to access these slots.

    • Insert the back end of the forceps into one of these slots. You may also use any other flat, narrow tool that fits into the slots.

    • Gently push the forceps into device. You should feel movement or hear a click, signifying this side of the device is unlocked.

    • Repeat with the other slot to completely unlock the device.

  3. %Livraison gratuite pour toute commande supérieure à 100,00 $US ou contenant un Pro Tech Toolkit !

    Parcourez notre boutique

    Vous avez déjà réparé quelque chose ? Vous êtes un génie.

    Partagez votre réparation avec le hashtag #ImAGenius

    Nous sommes tous des génies

    Partagez votre réparation avec le hashtag #ImAGenius

  4. Grab the top and the bottom of the device and gently pull the device open. Continue pulling until you have completely removed the top cover of the device. When reassembling your device, make sure the standby key is properly in place. See the Standby Key Guide for more information.
    • Grab the top and the bottom of the device and gently pull the device open.

    • Continue pulling until you have completely removed the top cover of the device.

    • When reassembling your device, make sure the standby key is properly in place. See the Standby Key Guide for more information.

    • Also ensure that when you close the two sides of the cover the LED indicator lights are inside the information panel.

  5. After opening the router, grab the upper left corner of the sliver face plate and gently pull the motherboard out of the slot from within the case. After opening the router, grab the upper left corner of the sliver face plate and gently pull the motherboard out of the slot from within the case.
    • After opening the router, grab the upper left corner of the sliver face plate and gently pull the motherboard out of the slot from within the case.

  6. Slowly lift the motherboard out of the case. Slowly lift the motherboard out of the case. Slowly lift the motherboard out of the case.
    • Slowly lift the motherboard out of the case.

Conclusion

To replace the motherboard, follow these instructions in reverse order.

4 autre(s) ont terminé cette réparation.

Cayce Rast

Membre depuis le 13/10/2014

409 Réputation

3 tutoriels rédigés

Équipe

Clemson, Team 1-2, Benson Fall 2014 Membre de l'équipe Clemson, Team 1-2, Benson Fall 2014

CLEM-BENSON-F14S1G2

3 membres

5 tutoriels rédigés

Voir les statistiques:

Dernières 24 heures : 2

7 derniers jours : 5

30 derniers jours : 39

Total : 5,520