Introduction

In this guide, we will give you step-by-step instructions on how to detach the lens from the logic board so that it can be replaced or repaired.

Pièces

Aucune pièce nécessaire.

  1. Remove the memory stick from the camera.
    • Remove the memory stick from the camera.

    • Remove the batteries from the camera.

    Ajouter un commentaire

  2. Remove all six 4.3mm silver screws along the perimeter of the camera using the Phillips #00 screwdriver.
    • Remove all six 4.3mm silver screws along the perimeter of the camera using the Phillips #00 screwdriver.

    • There is one screw hidden under the AV cover that also needs to be removed.

    Ajouter un commentaire

    • Pry the back cover from the left side of the camera. Remove the cover gently.

    Ajouter un commentaire

    • CAUTION! This is where energy for the flash is stored. Even with batteries removed, if you touch these connections, you can be shocked, depending on if the flash capacitor has a stored charge. It may not have a stored charge, but work around this assuming it does.

    • Newer cameras of descent quality usually have a bleeder resistor to drain the flash capacitor. This may not work anymore and the flash capacitor may still have a charge.

    Ajouter un commentaire

    • Remove the tape on the right side of the LCD screen.

    • Gently lift the LCD screen from its base.

    • Don't tug on the screen because it is still connected to the logic board.

    Be very careful not to touch the flash capacitor on far left when lifting the LCD!! It WILL shock you.

    Mark Fraylick - Réponse

    Getting the LCD ribbon back "in" is my problem -- hints or suggestions?

    richardkujawa - Réponse

    I can't get a feel for how the black clip holds the ribbon - insert the new one at an angle?

    richardkujawa - Réponse

    I practiced a few times with the "bad screen" and managed to figure this out. Unfortunately I can't explain how I did it... if some other person can explain how to make the ribbon connection/clip re-install more predictable I think it'd help anyone else who tries the repair.

    richardkujawa - Réponse

    • Lift the black latch connecting the LCD ribbon to the logic board.

    • Gently pull the LCD ribbon out.

    Ajouter un commentaire

    • Pry back the front cover of the camera starting from the right side.

    Ajouter un commentaire

    • Remove the 6 screws anchoring the LCD base to the logic board using the Phillips #00 screwdriver.

    • Remove the LCD base plate.

    Ajouter un commentaire

    • Lift the black latch connecting the LCD ribbon to the logic board.

    • Gently pull the lens ribbon out.

    Ajouter un commentaire

    • Desolder the connection of the logic board to the lens ribbon using a soldering iron and desoldering wick.

    • You will need to have the soldering equipment specified to complete this step.

    Ajouter un commentaire

    • Lift up the black and copper covering on the left side of the camera.

    Ajouter un commentaire

    • Pull the wiring at the top right of the camera away from the lens with tweezers.

    Ajouter un commentaire

    • Remove the cross-hair shaped wire cap to the left of the lens.

    Ajouter un commentaire

    • Remove the 3 screws holding the lens to the camera frame.

      • Two 3.8mm black Phillips #00 screws on the sides of the lens.

      • One 4.6mm silver Phillips #00 screw on the bottom of the lens.

    Ajouter un commentaire

    • There is a screw behind flash tube holding lens. Remove it, then gently pull the lens out. Be sure that the lens's ribbon clears the logic board.

    Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

5 autre(s) ont terminé cette réparation.

Andrea Govea

Membre depuis le 11/10/2010

357 Réputation

2 tutoriels rédigés

Équipe

Cal Poly, Team 9-23, Regan Fall 2010 Membre de l'équipe Cal Poly, Team 9-23, Regan Fall 2010

CPSU-REGAN-F10S9G23

4 membres

5 tutoriels rédigés

Be careful. I got painful shock from the flash capacitor even though the camera had been turned off and the batteries removed. It is the red and black wires and green tube on the left side.

Discharge it through a resistor. Trying to short it with a screwdriver made ahuge spark and left a mark on the screwdriver.

sdalimon - Réponse

Aconteceu-me o mesmo, agora não a consigo ligar.

O meu caro Sdalimon tem alguma sugestão?

Cumprimentos.

Alberto Lopes - Réponse

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 1

30 derniers jours : 31

Total : 15,675