Réparez vos affaires Communauté Boutique

Nikon D7000 Tripod Plate Replacement

Introduction

Use this guide to replace the tripod plate.

Ce dont vous avez besoin

  1. Nikon D7000 Tripod Plate Replacement, Motherboard: étape 1, image 1 de 1

    • Remove the following 5 screws securing the bottom cover to the camera body:

    • Four 6 mm J000 screws.

    • One 8 mm J000 screw (under lens mount).

    Modifier

  2. Nikon D7000 Tripod Plate Replacement: étape 2, image 1 de 1

    • Remove three 6 mm J000 screws from under the battery cover.

    Modifier

  3. Nikon D7000 Tripod Plate Replacement: étape 3, image 1 de 2 Nikon D7000 Tripod Plate Replacement: étape 3, image 2 de 2

    • Gently pull the bottom cover off of the camera body.

    Modifier

  4. Nikon D7000 Tripod Plate Replacement: étape 4, image 1 de 1

    • Remove the following screws from the port area:

    • Two 3.5 mm J000 screws.

    • One 6 mm J000 screw (right above ports).

    Modifier

  5. Nikon D7000 Tripod Plate Replacement: étape 5, image 1 de 1

    • Peel the rear rubber piece off with tweezers.

    Modifier

  6. Nikon D7000 Tripod Plate Replacement: étape 6, image 1 de 1

    • Remove one 4.25 mm J000 screw from behind the rear rubber piece.

    Modifier

  7. Nikon D7000 Tripod Plate Replacement: étape 7, image 1 de 1

    • Pull the eyepiece cover up to remove it.

    Modifier

  8. Nikon D7000 Tripod Plate Replacement: étape 8, image 1 de 1

    • Remove two 6 mm J000 screws from behind the eyepiece cover.

    • On D7100 models, there is an additional screw holding the back plate on. This screw is located in the diopter (dial with + - on it). This screw can be accessed by peeling up this sticker on the diopter.

    Modifier

  9. Nikon D7000 Tripod Plate Replacement: étape 9, image 1 de 1

    • Open the SD card cover by pushing slightly down with your thumb and sliding up.

    Modifier

  11. Nikon D7000 Tripod Plate Replacement: étape 10, image 1 de 1

    • Remove four 6 mm J000 screws that secure the SD card cover.

    Modifier

  12. Nikon D7000 Tripod Plate Replacement: étape 11, image 1 de 1

    • Gently pull the SD card cover off.

    Modifier

  13. Nikon D7000 Tripod Plate Replacement: étape 12, image 1 de 1

    • Remove the following screws that secure the back case:

    • One 6 mm J000 screw.

    • One 3 mm J000 screw.

    Modifier

  14. Nikon D7000 Tripod Plate Replacement: étape 13, image 1 de 1

    • Carefully lift the back case off.

    Modifier

  15. Nikon D7000 Tripod Plate Replacement: étape 14, image 1 de 3 Nikon D7000 Tripod Plate Replacement: étape 14, image 2 de 3 Nikon D7000 Tripod Plate Replacement: étape 14, image 3 de 3

    • Disconnect the following two ribbon cables from the motherboard.

    • See our Cable Connector Guide for help with ribbon cable connectors!

    Modifier

  16. Nikon D7000 Tripod Plate Replacement: étape 15, image 1 de 2 Nikon D7000 Tripod Plate Replacement: étape 15, image 2 de 2

    • Remove the following screws securing the left motherboard shield:

    • One 2 mm J000 screw (on the bottom).

    • One 3.5 mm J000 screw (on the back).

    • Be careful of the grounding clips on the motherboard.

    Modifier

  17. Nikon D7000 Tripod Plate Replacement: étape 16, image 1 de 1

    • Gently pry and lift the left motherboard shield off.

    Modifier

  18. Nikon D7000 Tripod Plate Replacement: étape 17, image 1 de 1

    • Remove one 3.5 mm J000 screw securing the right motherboard shield.

    Modifier

  19. Nikon D7000 Tripod Plate Replacement: étape 18, image 1 de 1

    • Gently lift the right motherboard shield off with the tip of a spudger.

    Modifier

  20. Nikon D7000 Tripod Plate Replacement: étape 19, image 1 de 3 Nikon D7000 Tripod Plate Replacement: étape 19, image 2 de 3 Nikon D7000 Tripod Plate Replacement: étape 19, image 3 de 3

    • Disconnect remaining ribbon cables.

    Modifier

  21. Nikon D7000 Tripod Plate Replacement: étape 20, image 1 de 2 Nikon D7000 Tripod Plate Replacement: étape 20, image 2 de 2

    • Disconnect remaining ribbon cables.

    Modifier

  22. Nikon D7000 Tripod Plate Replacement: étape 21, image 1 de 1

    • Carefully disconnect the red connector with tweezers.

    Modifier

  23. Nikon D7000 Tripod Plate Replacement: étape 22, image 1 de 1

    • Remove four 3.5 mm J000 screws securing the motherboard.

    Modifier

  24. Nikon D7000 Tripod Plate Replacement: étape 23, image 1 de 1

    • Gently pull the port side cover away from the motherboard.

    Modifier

  25. Nikon D7000 Tripod Plate Replacement: étape 24, image 1 de 1

    • Lift the motherboard off.

    Modifier

  26. Nikon D7000 Tripod Plate Replacement, Tripod Plate: étape 25, image 1 de 1

    • Remove four 6 mm J000 screws securing the tripod plate.

    Modifier

  27. Nikon D7000 Tripod Plate Replacement: étape 26, image 1 de 1

    • Carefully lift the tripod plate from the backside of the camera and slide out the grounding clip from under the lens mount.

    Modifier
Conclusion

To reassemble your device, follow these instructions in reverse order.

Une autre personne a terminé cette réparation.

Auteur

avec 2 autres contributeurs

Jed Chen

Membre depuis le 04/01/15

1 796 Réputation

3 tutoriels rédigés

Badges: 16

+ 13 badges supplémentaires

Équipe

Cal Poly, Team 24-6, Lancaster Spring 2015 Membre de l'équipe Cal Poly, Team 24-6, Lancaster Spring 2015

CPSU-LANCASTER-S15S24G6

3 membres

5 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 2

7 derniers jours : 9

30 derniers jours : 14

Total : 2,336