Réparez vos affaires

Droit à la réparation

Boutique

Ce tutoriel a des changements plus récents. Passer à la dernière version non vérifiée.

Parrot AR.Drone 2.0 Central Cross Replacement

Rédigé par : David Hoyt (et 9 autres contributeurs)
  • Commentaires : 5
  • Favoris : 3
  • Réparations terminées : 4

Difficulté

Modérée

Étapes

16

Temps nécessaire

25 - 45 minutes

Sections

2

Drapeaux

1

Incorrect Tools

Outils incorrects

Participez à l'amélioration de ce tutoriel en utilisant les outils adaptés dans les photos et/ou le texte.

Introduction

This video shows how to replace a damaged central cross. Music is the only audio. The tools are not specified.

AR.Drone 2.0 spare parts and mounting tools are available from several Parrot retailers.

Vidéo d'introduction

  1. Remove the foam body.

    • Remove the foam body.

    Traduire

  2. Disconnect the battery by pulling the two red wires apart. Remove the battery by releasing the battery retaining straps.

    • Disconnect the battery by pulling the two red wires apart.

    • Remove the battery by releasing the battery retaining straps.

    Traduire

  3. Turn the drone upside down. The cover is held on by plastic tape. Peel off the tape and use a spudger to remove the back cover.

    • Turn the drone upside down.

    • The cover is held on by plastic tape. Peel off the tape and use a spudger to remove the back cover.

    Traduire

  4. Using a spudger, separate the connector for the downward camera. Remove the camera from the body by pulling it off the foam body. Remove the camera from the body by pulling it off the foam body.

    • Using a spudger, separate the connector for the downward camera.

    • Remove the camera from the body by pulling it off the foam body.

    Traduire

  5. Use a spudger to release the black retaining clip. Then disconnect the connector to the sensors. Use tweezers to carefully remove the ribbon from the connector.

    • Use a spudger to release the black retaining clip. Then disconnect the connector to the sensors.

    • Use tweezers to carefully remove the ribbon from the connector.

    Traduire

  6. Remove the four 8mm torx screws with a T6 bit.

    • Remove the four 8mm torx screws with a T6 bit.

    • Remove the four 8mm philips head screws with a PH00 bit.

    Traduire

  8. Carefully pull the secondary board from the mainboard. Carefully pull the secondary board from the mainboard.

    • Carefully pull the secondary board from the mainboard.

    Traduire

  9. Turn the drone right side up Remove the USB connector from the battery retaining straps. Remove the USB connector from the battery retaining straps.

    • Turn the drone right side up

    • Remove the USB connector from the battery retaining straps.

    Traduire

  10. Release the rubber clip holding the USB and battery power cable to the body.

    • Release the rubber clip holding the USB and battery power cable to the body.

    Traduire

  11. Avoid using sharp tools near the battery. Push the USB and power cable through the battery panel.

    • Avoid using sharp tools near the battery.

    • Push the USB and power cable through the battery panel.

    Traduire

  12. Turn the drone upside down again. Use a spudger to release the connector and carefully remove the ribbon.

    • Turn the drone upside down again.

    • Use a spudger to release the connector and carefully remove the ribbon.

    Traduire

  13. Lift the mainboard up so that you can access the back. Disconnect the first connector with the white wires using a nylon spudger.

    • Lift the mainboard up so that you can access the back.

    • Disconnect the first connector with the white wires using a nylon spudger.

    • Disconnect the second connector with the red and black wires using a spudger.

    Traduire

  14. The mainboard is now fully detached and can be removed.

    • The mainboard is now fully detached and can be removed.

    Traduire

  15. Using a nylon spudger, peel off the four pieces of plastic securing the frame to the body.

    • Using a nylon spudger, peel off the four pieces of plastic securing the frame to the body.

    Traduire

  16. Carefully maneuver the four arms of the drone’s central cross until it detaches from the body by pulling apart the foam surrounding the arms.

    • Carefully maneuver the four arms of the drone’s central cross until it detaches from the body by pulling apart the foam surrounding the arms.

    Traduire

  17. The central cross can now be removed and replaced.

    • The central cross can now be removed and replaced.

    Traduire
Conclusion

To reassemble your device, follow these instructions in reverse order.

4 autre(s) ont terminé cette réparation.

Plume

avec 9 autres contributeurs

David Hoyt

Membre depuis le 09/04/2010

3 898 Réputation

43 tutoriels rédigés

Badges: 28

+ 25 badges supplémentaires

Équipe

Cal Poly, Team 25-89, Amido Spring 2010 Membre de l'équipe Cal Poly, Team 25-89, Amido Spring 2010

CPSU-AMIDO-S10S25G89

4 membres

52 tutoriels rédigés

2 commentaires

Ajouter un commentaire

If the crossbones are off just a bit would that effect the flight?

John Wurst - Réponse

So once I have removed the central cross, how do I put it all back together again?? I feel as though this is letting your guide down!!!!

Jacob Kenworthy - Réponse

Ajouter un commentaire

Afficher les statistiques:

Dernières 24 heures : 1

7 derniers jours : 7

30 derniers jours : 29

Total : 5,610