Réparez vos affaires

Droit à la réparation

Pièces & Outils

PlayStation 2 Slimline SCPH-7500x Fan Replacement

Rédigé par : Jared Hirata (et 12 autres contributeurs)
  • Commentaires : 0
  • Favoris : 5
  • Réparations terminées : 2

Difficulté

Modérée

Étapes

11

Temps nécessaire

15 minutes

Sections

2

Drapeaux

4

In Progress

En cours

Ce tutoriel est en cours de réalisation. Actualisez-le régulièrement pour découvrir les dernières modifications !

Confusing Text

Texte bizarre

Certaines parties de ce texte sont confuses, répétitives ou hors-sujet. Modifie-les pour les rendre plus claires !

Markup Mishap

Problème de balisage

Ce tutoriel nécessite de meilleures balises. Améliorez-le par des corrections ou des annotations de balisage.

Needs More Images

Nécessite plus d'images

Quelques images en plus, et les étapes de ce tutoriel seraient claires et nettes.

Introduction

This guide will walk you through step-by-step on how to properly remove and install the fan in the PlayStation 2 Slimline.

    • Turn off the PlayStation 2 (or PS2) and carefully unplug from the power source. Check to see there are no discs inside the console before flipping the game system upside-down.

    Modifier

  2. Locate the six feet on the bottom of the PS2.

    • Locate the six feet on the bottom of the PS2.

    • Five of the feet are in plain sight and one of the feet is located under the black void sticker on the bottom of the device.

    • IMPORTANT: Removing the black VOID sticker will void the warranty of this device. Proceed at your own risk

    • Some versions of the console, such as the PAL Version, may not have this sticker. In this case, the foot or even the screw should be in plain sight.

    Modifier

  3. Use a spudger, flathead screwdriver, or fingernail to pry the five visible feet from the bottom of the device. Use a spudger, flathead screwdriver, or fingernail to pry the five visible feet from the bottom of the device. Use a spudger, flathead screwdriver, or fingernail to pry the five visible feet from the bottom of the device.

    • Use a spudger, flathead screwdriver, or fingernail to pry the five visible feet from the bottom of the device.

    Modifier

  4. The sixth foot is located under the black VOID sticker. Remove the sticker before removing the foot underneath. The sixth foot is located under the black VOID sticker. Remove the sticker before removing the foot underneath.

    • The sixth foot is located under the black VOID sticker. Remove the sticker before removing the foot underneath.

    Modifier

  5. Fix Kits pour écrans LCD d'iPhone

    L'option économique couverte par notre garantie à vie.

    Acheter des kits

    Fix Kits pour écrans LCD d'iPhone

    Réduisez les coûts de réparation et non pas la qualité.

    Acheter des kits

  6. After all of the feet have been removed, locate the six 4.0mm screws on the base of the PS2. After all of the feet have been removed, locate the six 4.0mm screws on the base of the PS2.

    • After all of the feet have been removed, locate the six 4.0mm screws on the base of the PS2.

    Modifier

  7. Use a #1 Phillips screwdriver to unscrew all six 4.0mm screws from the base of the PS2. Use a #1 Phillips screwdriver to unscrew all six 4.0mm screws from the base of the PS2. Use a #1 Phillips screwdriver to unscrew all six 4.0mm screws from the base of the PS2.

    • Use a #1 Phillips screwdriver to unscrew all six 4.0mm screws from the base of the PS2.

    Modifier

  8. Once all of the screws have been removed, pull apart the top plastic cover from the bottom plastic cover. Start by lifting the side containing the power cable and Ethernet port. Then, lift the opposite side to fully separate. It will take force to pull apart the two halves. Once all of the screws have been removed, pull apart the top plastic cover from the bottom plastic cover. Start by lifting the side containing the power cable and Ethernet port. Then, lift the opposite side to fully separate. It will take force to pull apart the two halves. Once all of the screws have been removed, pull apart the top plastic cover from the bottom plastic cover. Start by lifting the side containing the power cable and Ethernet port. Then, lift the opposite side to fully separate. It will take force to pull apart the two halves.

    • Once all of the screws have been removed, pull apart the top plastic cover from the bottom plastic cover. Start by lifting the side containing the power cable and Ethernet port. Then, lift the opposite side to fully separate. It will take force to pull apart the two halves.

    Modifier

  9. If done correctly, you should have a fully detached plastic backing, revealing the electronic components of the PlayStation 2.

    • If done correctly, you should have a fully detached plastic backing, revealing the electronic components of the PlayStation 2.

    Modifier

  10. Locate the fan component of the motherboard of the PS2. With your fingers or tweezers, peel off the sticker that holds down the fan's wiring. Locate the fan component of the motherboard of the PS2. With your fingers or tweezers, peel off the sticker that holds down the fan's wiring. Locate the fan component of the motherboard of the PS2. With your fingers or tweezers, peel off the sticker that holds down the fan's wiring.

    • Locate the fan component of the motherboard of the PS2. With your fingers or tweezers, peel off the sticker that holds down the fan's wiring.

    Modifier

  11. With tweezers, detach the terminal to the cord from the motherboard to the fan. With tweezers, detach the terminal to the cord from the motherboard to the fan.

    • With tweezers, detach the terminal to the cord from the motherboard to the fan.

    Modifier

  12. Locate and unscrew the three 1.6mm screws located next to the base of the fan. Locate and unscrew the three 1.6mm screws located next to the base of the fan.

    • Locate and unscrew the three 1.6mm screws located next to the base of the fan.

    Modifier
Conclusion

To reassemble your device, follow these instructions in reverse order.

2 autre(s) ont terminé cette réparation.

Auteur

avec 12 autres contributeurs

Jared Hirata

Membre depuis le 09/04/2013

553 Réputation

7 tutoriels rédigés

Badges: 11

+ 8 badges supplémentaires

Équipe

Cal Poly, Team 17-4, Regan Spring 2013 Membre de l'équipe Cal Poly, Team 17-4, Regan Spring 2013

CPSU-REGAN-S13S17G4

3 membres

14 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Ajouter un commentaire

Afficher les statistiques:

Dernières 24 heures : 0

7 derniers jours : 7

30 derniers jours : 29

Total : 2,068