Introduction

56k internal modem, standard on all models.

  1. Turn the keyboard locking screw so that it is parallel to the space bar.
    • Turn the keyboard locking screw so that it is parallel to the space bar.

    • Pull the keyboard release tabs toward you and lift up on the keyboard until it pops free.

    • Lift the keyboard out by pulling it up and away from you. Rest the keyboard, face down, on top of the track pad.

    Ajouter un commentaire

  2. Pull the keyboard ribbon straight up from the logic board. Place the keyboard aside.
    • Pull the keyboard ribbon straight up from the logic board. Place the keyboard aside.

    • The connector may be tight. Gently rock the connector from side to side while pulling directly upward to free it. You can use this technique on many of the cards and cables you'll be disconnecting.

    • Make sure you have removed the laptop battery and CD/DVD modules from the expansion bays before proceeding.

    Ajouter un commentaire

    • Your laptop should look approximately like this.

    Ajouter un commentaire

    • Remove the two silver Phillips #1 screws that attach the heat shield to the internal metal framework.

    • Lift the heat shield up and pull it toward you.

    On my M7572, these are T9s not Philips.

    Rufleyboy - Réponse

    • Your laptop should look approximately like this.

    Ajouter un commentaire

    • Skip this step if your computer does not have an Airport card installed.

    • Firmly grasp the plastic tab attached to the Airport card and pull up and then to the right.

    • The Airport card is still attached to the antenna cable, so don't just yank it out of the slot.

    On mine, the airport card had been put it with the orange ribbon OVER the top, so had to unplug the righthand connector and then plug it back in after (see pic for Step 8)

    Rufleyboy - Réponse

  3. Répandez la magie de Noël
    Obtenez 12 $ de réduction sur les commandes de 50 $ ou plus avec le code FIXMAS12
    Répandez la magie de Noël
    Obtenez 12 $ de réduction sur les commandes de 50 $ ou plus avec le code FIXMAS12
    • Disconnect the antenna cable from the Airport card.

    Ajouter un commentaire

    • Pull the battery cable directly up from the logic board.

    • Remove the battery from its holder by pulling up and to the left.

    Ajouter un commentaire

    • Your laptop should look approximately like this.

    Ajouter un commentaire

    • Remove the long silver Phillips #1 screw from the heat sink.

    • Remove the two T8 Torx screws that attach the heat sink to the processor.

    Ajouter un commentaire

    • Lift the heat sink up from the left side and pull it out.

    • If you need to mount the heat sink back into the laptop, we have a thermal paste guide that makes replacing the thermal compound easy.

    Ajouter un commentaire

    • Grasp the plastic tab on the processor's right side and pull it directly up.

    • Some processors may be missing the plastic pull tab. In this case, we suggest using a non-metal tool to gently pry up the processor. Slip the tool's thin edge under the front right corner of the processor and carefully pry it up.

    Ajouter un commentaire

    • Your laptop should look approximately like this.

    Ajouter un commentaire

    • Remove the black Torx screw from the right side of the modem.

    • Remove the small black plastic rectangle with four holes.

    Ajouter un commentaire

    • Use the tips of your fingers, a spudger, or a flat non-metal tool to get under the modem's edge and pry it up from its socket.

    Ajouter un commentaire

    • Disconnect the cable from the right side of the modem.

    Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

Pièces jointes

iRobot

Membre depuis le 24/09/2009

1 Réputation

623 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 0

Total : 3,345