Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.
Introduction
Ce guide de remplacement explique comment retirer un écran LCD défectueux d'un appareil photo Sony a7 numéro de modèle ILCE-7. L'écran LCD est une partie essentielle de l'appareil photo qui permet à l'utilisateur de revoir les photos ou d'accéder au menu des paramètres et de modifier les paramètres de qualité de la photographie. Voici les étapes à suivre pour remplacer l'écran LCD.
Si l'écran de l'appareil photo devient noir ou si l'écran ne répond pas aux commandes, il se peut que l'écran LCD de l'appareil photo soit en panne.
Ce dont vous avez besoin
-
-
Retournez l'appareil photo à l'envers et observez où se trouvent le couvercle de la batterie et l'interrupteur sur l'appareil photo.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the eyepiece cover by removing the four M1.5x4mm screws with a PH00 Phillips screwdriver.
-
Remove the M1.5x4mm screw that retains the adjustment wheel with a PH00 Phillips screwdriver.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the six M1.5x4mm screws with a PH00 Phillips screwdriver.
-
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove one M1.5x4mm screw with a PH00 Phillips screwdriver.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Once the screws have been removed, unsnap and lift the rear plastic cover off of the camera.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
Outil utilisé dans cette étape :Tweezers$4.99-
Using the blunt tweezers, remove the blue ribbon cable.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Place the tweezers on the side of the circuit board and lift it from underneath so as to free it from the three retaining tabs.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove four M1.5x4mm screws using a PH00 Phillips screwdriver.
On my A7 the screw shown first top right was a different thread to the other three, take care to put back in the correct place
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the metal plate and LCD screen away from the camera body.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Detach the amber ribbon cable from the motherboard.
13단계에서 14단계로 오는사이에 마더보드의 왼쪽 아래부분 나사 푸는 부분이 누락된것 같습니다. 아래 20단계에서 억늡한 나사 2개 이외에 아래쪽 2개를 더 푸는것을 추가해야 합니다.
그리고 8단계 2번째 사진의 나사는 풀 필요가 없는 나사인데.. 왜 풀어야 하는지요??
-
-
-
Retirez le câble ruban qui relie l'écran LCD à l'appareil photo à l'aide des outils d'ouverture iFixit.
-
Pour remonter votre appareil, suivez ces instructions dans l'ordre inverse.
Pour remonter votre appareil, suivez ces instructions dans l'ordre inverse.
Annulation : je n'ai pas terminé ce tutoriel.
4 autres ont terminé cette réparation.
Merci à ces traducteurs :
100%
[deleted] nous aide à réparer le monde ! Vous voulez contribuer ?
Commencez à traduire ›
6 commentaires
this isn’t finished
Hello,
If by “isn’t finished” you mean that the instructions do not contain the steps to put the camera back together, this was done in the hope that the user would follow the steps in a reverse order to put the camera back in one piece.
Best.
Hello there,
Thank you for your constructive comment. The criteria we needed to meet for this project was to provide instruction on iFixit guides for how to remove various parts on the device. We were being evaluated on the content pertaining to our writing and not the technical depth of the guide. Furthermore, we did not have a vested interest in replacing the screen nor did we have another screen to replace it with. In your rush to make a rude comment, you might have missed the end of the guide where it states that in order to reassemble you must follow the steps we provided in the reverse order. Reverse means doing something in the opposite direction.
Regards.
Thanks for the guide.
Thank you! Appreciated the clear instructions.. I have one question is the new screen price range is around 20 to 30$ ? I find it cheap to be true but at the same time I hope it’s 😄