Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.
Ce dont vous avez besoin
-
-
Avec un outil en plastique ou votre ongle, faites levier dans l'encoche à gauche de la caméra arrière, à côté du bouton power.
-
-
-
Utilisez le bout plat d'un spudger ou votre ongle pour enfoncer légèrement la carte microSD dans son logement jusqu'à ce que vous entendiez un clic.
-
Après le clic, lâchez la carte et elle sortira de son logement.
-
Retirez la carte microSD.
-
-
-
Insérez un outil en plastique ou votre doigt dans l'encoche du compartiment de la batterie et soulevez la batterie.
-
Retirez la batterie du téléphone.
-
-
-
Utilisez un outil en plastique ou votre ongle pour pousser légèrement la carte SIM dans sa fente jusqu'à ce que vous entendiez un clic.
-
Après le clic, lâchez la carte et elle va sortir de son emplacement.
-
Retirez la carte SIM.
-
-
-
Dévissez les neuf vis cruciformes #00 de 4,0 mm fixant le châssis à l'écran.
-
-
-
-
En commençant du côté bouton de volume du smartphone, insérez votre outil en plastique entre le joint en chrome autour de l'écran et la pièce-cadre en chrome plus large. Cherchez la jointure entre les deux.
-
Faites glisser l'outil en plastique le long de la jointure et ouvrez les clips en plastique au fur et à mesure.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use the flat end of a spudger to disconnect the USB board cable connector from the motherboard.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Gently insert the point of a spudger between the USB port and the USB port bracket to pry one side of the bracket off of its post.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Disconnect the soft button cable from the USB board cable.
-
Disconnect the antenna cable connector from the USB board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Gently insert the flat end of a spudger beneath the USB board to free it from the adhesive holding it in place.
-
Annulation : je n'ai pas terminé ce tutoriel.
206 autres ont terminé cette réparation.
24 commentaires
I found this guide excellent and it is very easy to do. I didnt have the plastic opening tool but I do have a long thumbnail. It worked very well.
Too bad the replacement board I got has a defective soft button connector. I had to disassemble the phone 3 times. I thought I did It wrong the 1st time. Opened the phone a 2nd time to check.... closed the phone... nada.... USB changer works but no soft keys... put my old board back in to check the soft buttons and they work. Sent an email to the company that I bought the board from... still no answer after 24hrs. If I still have no answer by the end of the week I will post which company sold me the defect board so no one else gets burned from them. I will then try to unsolder the USB from the new board to replace the USB on my old one.
This guide needs an update as it does not include the 4G antenna on the left side of the device that is under the USB cable and hooks up at the bottom left on the USB board up to just beside the USB connector above the battery. Pictures 12, 15, & 16 will need updated to show this cable.
To follow rnbhays' comment about the antenna connector on the left, it is specifically for i545 Verizon models.
I strongly suggest people to disconnect both left and right cables from the USB board prior to removing it. While doing so, my tool slipped and I accidentally broke the left cable. Thankfully I was able to crimp the connector back on the cable with tweezers and a magnifying glass 'til I get another cable ordered.
It also applies to the Sprint version as well. I have an LTE cable on the left side, and had to be very careful purchasing a replacement part to make sure it was the right one.
After replacement my microphone element isn't working. Possible reasons?