Introduction

Before attempting this guide complete the CD Tray Removal Guide.

Pièces

Aucune pièce nécessaire.

  1. Using a Phillips head screwdriver remove  six screws from the bottom of the console.
    • Using a Phillips head screwdriver remove six screws from the bottom of the console.

      • The six screws are marked.

    Ajouter un commentaire

  2. Remove the two screws that attach the Genesis' connector to the rest of the console.
    • Remove the two screws that attach the Genesis' connector to the rest of the console.

      • The two screws are marked in the diagram.

    Ajouter un commentaire

    • Slide the lock tab to the left to separate the halves of the console.

    Ajouter un commentaire

    • Lift from the left side to remove the top of the case.

    Ajouter un commentaire

    • Using the spudger, pry the cover off of the Genesis attachment.

    Ajouter un commentaire

    • Lift the top of the case to remove the cover.

    Ajouter un commentaire

    • Remove the faceplate by pulling it up, then out.

    Ajouter un commentaire

    • Remove metal plate by unscrewing the three screws with the Phillips head screwdriver and then lifting the plate.

      • The three screws are shown on the diagram.

    Ajouter un commentaire

    • Remove the two screws from the plastic bar.

      • The two screws are shown pictured.

    Ajouter un commentaire

    • To remove the CD tray

      • Remove the four screws with the Phillips head screwdriver.

    Ajouter un commentaire

    • Carefully unplug the wire connected to optical reader.

    Ajouter un commentaire

    • Remove the four screws on the underside of the CD tray with a small Phillips head screwdriver.

      • The four screws are highlighted on the diagram.

    • The four springs below the circuit board are attached to the screws, so be careful not to lose them when you remove the screws.

    Ajouter un commentaire

    • Carefully remove the CD tray from circuit board.

    Ajouter un commentaire

    • Remove the two bronze screws from the metal plate with a medium Phillips head screwdriver.

      • The screws are marked on the diagram.

    • Carefully lift the metal plate up to expose the motherboard.

      • There is a wire strip running through the metal plate that is soldered to motherboard and power supply board. The plate cannot be completely removed. Do NOT force plate upwards. All the ribbon cables can be safely unplugged by simply pulling them out of their slots.

    The yellow circles in this diagram are incorrect. There are 3 screws on the main board assembly. 2 on the left and one correctly indicated on the bottom right. The top right yellow circle does not belong.

    myersni06 - Réponse

    • Carefully lift off the metal plate, the motherboard, and the CD tray circuit board. Then, flip each piece over, as pictured.

    Ajouter un commentaire

    • Remove the two screws from the power supply using a medium Phillips head screwdriver.

      • The two screws are marked on the diagram.

    Ajouter un commentaire

    • Remove the power supply unit from the console by lifting the unit up.

    Ajouter un commentaire

    • This is what the motherboard unit will look like once removed.

    Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

3 autre(s) ont terminé cette réparation.

Ryan Kotzebue

Membre depuis le 07/10/2010

243 Réputation

4 tutoriels rédigés

Équipe

Cal Poly, Team 5-14, Maness Fall 2010 Membre de l'équipe Cal Poly, Team 5-14, Maness Fall 2010

CPSU-MANESS-F10S5G14

5 membres

6 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 1

7 derniers jours : 10

30 derniers jours : 43

Total : 7,834