This is the replacement guide for the motherboard in the Microsoft Xbox.

  1. Make sure your Xbox is safely unplugged and is laying on a flat, stable surface.
    • Make sure your Xbox is safely unplugged and is laying on a flat, stable surface.

    Ajouter un commentaire

  2. Turn the Xbox over to reveal the four rubber feet.
    • Turn the Xbox over to reveal the four rubber feet.

    • Use a metal spudger to pry off the four rubber feet.

    The screw is in the outside corner. If you pry up only the half of the foot on that side, you can easily remove the (very long) screw, and the foot will stay attached.

    Ian Butler - Réponse

    • There are 2 more screws hidden under the two labels on the bottom of the case.

    • You can either remove the labels or simply feel for the screw holes through the labels and then cut or punch a hole through them.

    It is also easy to feel for the screw hole with your finger and then cut a hole, or punch it out with the tip of the Torx driver to reveal the screw.

    Ian Butler - Réponse

    • Remove the six T20 Torx screws securing the top cover to the bottom cover.

    Ajouter un commentaire

    • Wedge a metal spudger and carefully pry upwards to slightly separate the top and bottom covers.

    • Flip the Xbox right side up.

    • Hold the sides and lift the Xbox slightly off the bench. A gentle shake of the unit should see the top cover separate from the rest of the unit quite easily.

    • Placing the Xbox on your lap while separating the top and bottom covers may make the process easier.

    Ajouter un commentaire

    • Once the bottom and top shells are no longer attached, carefully turn the Xbox right-side-up, lift and remove the top cover.

    Ajouter un commentaire

  3. Répandez la magie de Noël
    Obtenez 12 $ de réduction sur les commandes de 50 $ ou plus avec le code FIXMAS12
    Répandez la magie de Noël
    Obtenez 12 $ de réduction sur les commandes de 50 $ ou plus avec le code FIXMAS12
    • Remove the three 3 mm T10 screws securing the hard drive to the Xbox.

    • There is one screw on the rear left side of the hard drive that is only visible when the IDE ribbon cable is lifted up. The other two are at the front right and left sides of the hard drive.

    • The screw on the lower left corner of the disk drive is not in the hole that it appears to be in, but rather just closer to the corner.

    Ajouter un commentaire

    • Free the hard drive power cable from the carrier for sufficient slack to lift the hard drive out.

    • Lift the plastic hard drive carrier out of the Xbox case.

    Ajouter un commentaire

    • Remove the four 3.4 mm T15 Torx screws from the plastic hard drive carrier (two screws per side).

    • Carefully remove the hard drive from the plastic carrier. Gentle rocking will see the hard drive come out quite easily.

    Ajouter un commentaire

    • Pull both the hard drive data ribbon cable and the power cable straight up from the hard drive.

    • They may be firmly seated, so be careful trying to remove them. DO NOT pull the wires as you may damage the cable assembly.

    Remember that the new drive will only work if it has been properly prepared, and the Xbox has been modified.

    Ian Butler - Réponse

    • Remove the disk drive. It should come right out.

    • Unplug the ribbon cable and yellow cables from back of disk drive.

    I dont got the tools and i dont know how to do ut

    jacob lowery - Réponse

    • Pry back the black plastic tabs around the disk drive in order to remove it from its housing. Once removed, set the drive aside.


    It is ok to remove the drive if it isn't dead. If repairs are required to the drive it needs to be removed from the drive's housing.

    Navy Vet 2015 - Réponse

    • Unplug the multi-colored power cord from the motherboard. It is in there pretty tightly, so it may take some effort.

    Ajouter un commentaire

    • Using T10 Torx screwdriver, remove two 3mm screws from the tan power supply board.

    Ajouter un commentaire

    • Remove the power supply and set it aside. It should lift right out.

    • Be very careful not to touch the copper coil or capacitors on the power supply. They may shock you.

    Ajouter un commentaire

    • Unplug the bundle of yellow cables as well as the rainbow cord from the motherboard.

    Ajouter un commentaire

    • Remove eleven 3mm screws from motherboard, using a T10 Torx screwdriver. Refer to the picture to find all eleven.

    • Unplug the power cable attached to the fan.

    Ajouter un commentaire

    • Remove the motherboard from the Xbox. As long as all of the screws are out and the fan is disconnected, it will lift out easily.

    Ajouter un commentaire


To reassemble your device, follow these instructions in reverse order.

26 autre(s) ont terminé cette réparation.


Membre depuis le 29/10/2009

3 609 Réputation

5 tutoriels rédigés


Cal Poly, Team 18-2, Maness Fall 2009 Membre de l'équipe Cal Poly, Team 18-2, Maness Fall 2009


3 membres

10 tutoriels rédigés

Utilize the information on this website to determine what Xbox version you have so you know what replacement parts to look for.

Navy Vet 2015 - Réponse

What about the key lock between the HDD and original motherboard? Wouldn't you get an error message installing a new motherboard?

chris - Réponse

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 3

7 derniers jours : 31

30 derniers jours : 180

Total : 31,700