Aller au contenu principal

Réparez vos affaires

Droit à la réparation

Pièces & Outils

Introduction

Bumpers can become loose over time and not function properly. This guide will show you how to remove the faceplate to be able to access the bumpers.

  1. Remove battery pack cover.
    • Remove battery pack cover.

    • Remove batteries.

    • Carefully remove sticker or puncture where you feel the screw.

  2. Remove the side handles by wedging the spudger in between the front and side panels. Pry the side panel by moving the  spudger back and forth. You must do this along the entire seam to remove the side handle panel. Pry the side panel by moving the  spudger back and forth. You must do this along the entire seam to remove the side handle panel.
    • Remove the side handles by wedging the spudger in between the front and side panels.

    • Pry the side panel by moving the spudger back and forth. You must do this along the entire seam to remove the side handle panel.

  3. Essential Electronics Toolkit

    Petit kit. Grandes possibilités.

    Shop Toolkits

    Essential
    Electronics
    Toolkit

    Shop Toolkits
  4. Removing the side handles allows access to remove the faceplate. Use the TORX TR8 Size 8 Screwdriver to remove the TR9 Torx Screws Use the TORX TR8 Size 8 Screwdriver to remove the TR9 Torx Screws
    • Removing the side handles allows access to remove the faceplate.

    • Use the TORX TR8 Size 8 Screwdriver to remove the TR9 Torx Screws

  5. Now that the bumpers are easily visible make sure to clean any dirt or grime that may be around the bumpers. The bumpers are connected by a middle plastic cover that is around the Xbox button. Remove this plastic piece to fully reveal the bumpers. Be aware of the sync button loosely placed under the plastic covering. Ensure it is put back before putting back the bumper/plastic cover assembly. (pictured in picture 3)
    • Now that the bumpers are easily visible make sure to clean any dirt or grime that may be around the bumpers.

    • The bumpers are connected by a middle plastic cover that is around the Xbox button. Remove this plastic piece to fully reveal the bumpers.

    • Be aware of the sync button loosely placed under the plastic covering. Ensure it is put back before putting back the bumper/plastic cover assembly. (pictured in picture 3)

    • Remove the current bumper assembly by pulling them off the plastic cover. Put on the new bumpers and reassemble that section.

Conclusion

To reassemble your device, follow these instructions in reverse order.

32 autre(s) ont terminé cette réparation.

Ryan Burroughs

Membre depuis le 25/09/2017

891 Réputation

2 tutoriels rédigés

Équipe

USF Tampa, Team S9-G1, Remmell Fall 2017 Membre de l'équipe USF Tampa, Team S9-G1, Remmell Fall 2017

USFT-REMMELL-F17S9G1

4 membres

4 tutoriels rédigés

the bumpers take some finesse to remove, so be patient

Vincent - Réponse

You should add a security hex screwdriver to your tools list, along with the gauge that is required.

Travis Weston - Réponse

There is a fifth screw in the battery compartment that holds the faceplate on. Take an exacto knife and cut out sticker where the hole is.

Scott Williams - Réponse

Could you elaborate on the “remove the bumpers” part (last step) please, thank you.

r.d.huijsmans - Réponse

Great guide. Helped me easily fix a sticky bumper and save 60$

Bryon Crockett - Réponse

Ajouter un commentaire

Afficher les statistiques:

Dernières 24 heures : 66

7 derniers jours : 464

30 derniers jours : 2,030

Total : 27,684