Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.
Ce dont vous avez besoin
-
Cette étape n’est pas traduite. Aidez à la traduire
-
To aid in visualization, the two clips boxed in red are located closest to the headphone jack.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Insert the large iPod opening tool into the seam between the front case and rear panel of the iPod, above the dock connector. The tool's edge should point toward the rear panel to prevent any accidental scratching of the anodized aluminum front case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Insert a small iPod opening tool into the seam on the headphone jack side of the Nano, with the edge of the tool pointing toward the rear panel.
-
Gently enlarge the existing gap by pressing/wiggling the small iPod opening tool into the gap near each of the the two tabs attached to the rear case, pushing the clips toward the center of the Nano until both have been freed.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Repeat the same procedure listed in the previous step to free the three clips along the hold switch side of the Nano.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Insert an iPod opening tool into the gap near the top left corner of the Nano and work to free the three clips along the top edge of the rear panel.
-
After ensuring all tabs are free, separate the two halves of the iPod.
-
The rear panel is now free from the iPod.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
With the rear case removed, the back side of your Nano should now look like this.
-
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the following six screws:
-
One 1.8 mm Phillips.
-
Three 1.9 mm Phillips.
-
One 2.4 mm Phillips.
-
One 2.6 mm Phillips.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Using a spudger, flip up the brown click wheel ribbon cable retaining clip.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use the tip of a spudger to slide the click wheel ribbon cable out of its socket.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the logic board assembly out of the front case from the click wheel connector side (the cable you just disconnected). Rotate the logic board assembly about the display ribbon cable and lay it next to the front case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use a spudger to flip up the display ribbon cable retaining clip.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Slide the display ribbon cable out of its socket.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Before proceeding, remove the metal EMI finger shown by pulling it away from the adhesive on the logic board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Before de-soldering the battery cables, you must remove a small amount of black rubbery adhesive securing them to the logic board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Push the tip of a spudger beneath the rubber adhesive and toward the battery to free it from the surface of the logic board.
-
Start freeing the adhesive from around one of the outer leads, then free it from the two gaps between leads, and finally push the spudger along the back side of the leads to completely remove it from the logic board/battery leads.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
The battery leads, now free of adhesive, should look like this.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Begin by heating the exposed end of the white battery lead with the tip of a soldering iron while simultaneously pulling the lead away from the connection, using tweezers to grasp the lead by the insulation.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
De-solder the remaining leads, following the procedure illustrated in the previous step.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
All leads should now be de-soldered and disconnected from the logic board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Using a spudger, pry the battery up from the adhesive holding it to the battery shield.
-
Start prying at the upper right corner of the battery and work your way around the perimeter until the battery has lifted enough to grab it with your fingers.
-
Remove the battery from the battery shield.
-