Introduction

Use this guide to replace the broken buttons to get back full functionality of your printer.

Remove the following two Phillips screws:
  • Remove the following two Phillips screws:

    • Two 7.85 mm Phillips #1 screws

Ajouter un commentaire

Pull the back cover off by lifting up on the cover.
  • Pull the back cover off by lifting up on the cover.

    • You may need to pull firmly as it requires quite a bit of force.

Ajouter un commentaire

  • Open the front tray.

Ajouter un commentaire

  • Lift the scanner compartment.

Ajouter un commentaire

  • After opening up the scanner compartment, make sure the blue lever locks into place, keeping the compartment open.

Ajouter un commentaire

  • Push the blue lever back while twisting it clockwise in order to remove the lever from its slot.

  • After removing the lever, close the scanner compartment and the scanner cover.

Ajouter un commentaire

  • Use the plastic opening tool to pry open the side cover.

Ajouter un commentaire

  • Flip the printer so that you are facing the underside.

  • Use the plastic opening tool to remove the corner of the side panel from the pin.

    • Plastic pin.

Ajouter un commentaire

  • Using the plastic opening tool, remove the side panel by loosening it from the bottom of the printer.

Ajouter un commentaire

  • Using the plastic opening tool, pry off the top cover of the LCD assembly (within the red box in the first picture).

    • Pry around the front and side edges for the easiest removal.

Ajouter un commentaire

  • After removing the top cover of the LCD assembly, remove the LCD using the plastic opening tool.

Ajouter un commentaire

  • Completely remove the LCD by disconnecting the ribbon cable from the LCD with a gentle pull.

Ajouter un commentaire

  • Locate the buttons on the printer.

Ajouter un commentaire

  • Using the plastic opening tool, gently pry around the button cover to remove it from its fixture.

Ajouter un commentaire

  • Remove the following five Philips screws:

    • Five 7.65 mm Philips #1 screws

Ajouter un commentaire

  • Using the plastic opening tool, gently pry around the cover behind the LCD Screen to remove it from its fixture.

Ajouter un commentaire

  • Remove the two screws using the Phillips #1 screwdriver.

    • Two 7.8 mm Phillips #1 screws

Ajouter un commentaire

  • Gently pull the LCD screen up to remove it from its fixture.

Ajouter un commentaire

  • Use the plastic opening tool to pry off the plastic button assembly.

Ajouter un commentaire

  • Gently pull the plastic button assembly up to remove it.

    • The plastic button assembly has a ribbon cable connected on the bottom, so make sure to be careful pulling it.

Ajouter un commentaire

  • Remove the ribbon cable connected to the backside of the plastic button assembly.

Ajouter un commentaire

  • Remove the seven screws using the Phillips #1 screwdriver.

    • Seven 8.7 mm Phillips #1 screws

Ajouter un commentaire

  • Locate the spring that holds the PCB in place on the bottom left of the plastic button assembly.

  • Gently lift the spring and pull the board out of its plastic button assembly.

Ajouter un commentaire

  • Remove the buttons from the plastic button assembly.

    • Buttons

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

Khutug Dorjsuren

Membre depuis le 14/01/2013

99 Réputation

2 tutoriels rédigés

Équipe

Cal Poly, Team 19-41, Regan Winter 2013 Membre de l'équipe Cal Poly, Team 19-41, Regan Winter 2013

CPSU-REGAN-W13S19G41

4 membres

6 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 4

Total : 1,135