Pièces

Aucune pièce nécessaire.

  1. Lay the Dell Optiplex GX260 down on a clean flat surface with the rear towards you.
    • Lay the Dell Optiplex GX260 down on a clean flat surface with the rear towards you.

    • Push the oval shaped buttons located on the top and bottom of the PC simultaneously and lift the case straight up.

    • Note: Some force may be required to push in the oval buttons open the PC case.

    cool de faires des sites comme ca :)

    baptiste Prando - Réponse

  2. Disconnect the fan cable from the motherboard.
    • Disconnect the fan cable from the motherboard.

    Ajouter un commentaire

    • On the rear of the desktop, push the two circled black buttons straight in with a small pointed object while pulling up on the fan.

    • Once the fan is released, lift it straight up and out of the case.

    Ajouter un commentaire

    • Push out on the cream colored tabs on each side of each RAM module until it pops up and out of its slot and remove the RAM.

    salope pute bite

    Albert einstein - Réponse

    tg beaufion travail

    Heinsenberg - Réponse

    Albert reste polie

    Heinsenberg - Réponse

    jvai tenculer baltringue va

    Heinsenberg - Réponse

  3. Livraison gratuite pour les commandes de plus de 20 $
    Indiquez le code BLUEANDBLACK au moment de payer
    Livraison gratuite pour les commandes de plus de 20 $
    Indiquez le code BLUEANDBLACK
    • Disconnect the ATX power cable to the motherboard.

    • Disconnect the P4 12V(4x2) power cable from the motherboard.

    Ajouter un commentaire

    • Disconnect the front panel ribbon cable by gently pulling it straight up.

    • Disconnect the hard drive ribbon cable by gently pulling the blue tab away from the motherboard.

    • Disconnect the optical drive ribbon cable by gently pulling the orange tab away from the motherboard.

    Ajouter un commentaire

    • Disconnect the floppy drive drive ribbon cable by gently pulling the black tab away from the motherboard.

    • Disconnect the optical drive audio cable connector from the motherboard.

    • Disconnect the audio input/output cable from the motherboard.

    Ajouter un commentaire

    • Lift the metal tab near the right corner of the motherboard.

    • Pull the green tab toward the front of the PC to release the motherboard.

    • From the rear of the PC, push the ports in while lifting the motherboard up and flipping it away from you.

    Ajouter un commentaire

    • Stand the motherboard up as shown.

    • Insert the flat end of a spudger into the slot in the motherboard mounting plate and press the release tab while pushing the extension plate to the right with your thumbs until it comes off..

    Ajouter un commentaire

    • Remove the screw at the rear of the motherboard.

    • Grasp the heat sink with your left hand and the I/O port panel with your right hand and pull to separate motherboard from the metal base.

    • If you are replacing the motherboard refer to the great iFixit guide for removing the CPU.

    Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

12 autre(s) ont terminé cette réparation.

Kevin Schapansky

Membre depuis le 05/10/2010

1 166 Réputation

9 tutoriels rédigés

Équipe

Cal Poly, Team 4-48, Amido Fall 2010 Membre de l'équipe Cal Poly, Team 4-48, Amido Fall 2010

CPSU-AMIDO-F10S4G48

4 membres

18 tutoriels rédigés

Mines stuck for some reason I almost bent the frame from pushing the ports in while lifting and pulling the tray tab away

james dee - Réponse

make sure you doing it the correct side!

Robert Stokes-Barnett -

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 4

7 derniers jours : 30

30 derniers jours : 116

Total : 31,497