Aller au contenu principal

Réparez vos affaires

Droit à la réparation

Boutique

Introduction

Use this guide to replace the bottom module in your Fairphone 3.

  1. Power off your phone before beginning disassembly. Insert a thumbnail, or a prying tool like a spudger, into the notch at the bottom right of the back cover.
    • Power off your phone before beginning disassembly.

    • Insert a thumbnail, or a prying tool like a spudger, into the notch at the bottom right of the back cover.

    • Pry the back cover up to start separating its plastic clips.

  2. Slide around the bottom right corner of the back cover to loosen the lower plastic clips. Lift the back cover to release the rest of the plastic clips and remove it. To reinstall the back cover press it firmly into place until you hear a snap from the plastic clips to form a seamless connection with the rear side of the phone.
    • Slide around the bottom right corner of the back cover to loosen the lower plastic clips.

    • Lift the back cover to release the rest of the plastic clips and remove it.

    • To reinstall the back cover press it firmly into place until you hear a snap from the plastic clips to form a seamless connection with the rear side of the phone.

  3. Use a fingernail or a prying tool at the marked notch to lever the battery out of its recess. Lever the battery up until you can get a good grip.
    • Use a fingernail or a prying tool at the marked notch to lever the battery out of its recess.

    • Lever the battery up until you can get a good grip.

  4. Lift the battery out of its recess and remove it. Lift the battery out of its recess and remove it.
    • Lift the battery out of its recess and remove it.

  5. Whenever a Phillips #00 screw is mentioned you can also unfasten it with a size #0 bit/screwdriver.
    • Whenever a Phillips #00 screw is mentioned you can also unfasten it with a size #0 bit/screwdriver.

    • Remove the thirteen Phillips #00 screws (4 mm length).

  6. Insert an opening pick between the midframe and the display module on the right edge of the phone. Slide the opening pick down to the bottom right corner to pry open the plastic clamps of the display module. Slide the opening pick down to the bottom right corner to pry open the plastic clamps of the display module.
    • Insert an opening pick between the midframe and the display module on the right edge of the phone.

    • Slide the opening pick down to the bottom right corner to pry open the plastic clamps of the display module.

  7. Slide the opening pick around the bottom right corner and use it to disengage the plastic clamps at the bottom of the display module. Slide the opening pick around the bottom right corner and use it to disengage the plastic clamps at the bottom of the display module.
    • Slide the opening pick around the bottom right corner and use it to disengage the plastic clamps at the bottom of the display module.

  8. Slide the opening pick along the left side to pry the display module up. The display module should pop out of the midframe during this process. In case it doesn’t, check for remaining clamps you might have missed.
    • Slide the opening pick along the left side to pry the display module up.

    • The display module should pop out of the midframe during this process. In case it doesn’t, check for remaining clamps you might have missed.

  9. Remove the display assembly. To reinstall the display-module press it into place on all sides until you can hear a snap from the plastic clamps to make sure it sits flush with the frame.
    • Remove the display assembly.

    • To reinstall the display-module press it into place on all sides until you can hear a snap from the plastic clamps to make sure it sits flush with the frame.

  10. Remove the four 4.1mm-longPhillips #00 screws.
    • Remove the four 4.1mm-longPhillips #00 screws.

  11. Use a spudger to pry up and disconnect the bottom module connecting cable. Use a spudger to pry up and disconnect the bottom module connecting cable.
    • Use a spudger to pry up and disconnect the bottom module connecting cable.

  12. Use your fingers to remove the bottom module. Use your fingers to remove the bottom module.
    • Use your fingers to remove the bottom module.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Information on what to do with the old module can be found on the FairPhone support page and in the FairPhone forum.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Answers community for help.

4 autre(s) ont terminé cette réparation.

Adriana Zwink

Membre depuis le 18/12/2019

7 948 Réputation

40 tutoriels rédigés

Équipe

iFixit Membre de l'équipe iFixit

Community

135 membres

13 858 tutoriels rédigés

Ajouter un commentaire

Afficher les statistiques:

Dernières 24 heures : 2

7 derniers jours : 17

30 derniers jours : 119

Total : 540