Réparez vos affaires Communauté Boutique

KitchenAid KHM512ER Eject Button Spring Replacement

Introduction

Beater Eject Button doesn't work? Follow this guide to replace it.

Ce dont vous avez besoin

  1. KitchenAid KHM512ER Eject Button Spring Replacement, Eject Button Spring: étape 1, image 1 de 2 KitchenAid KHM512ER Eject Button Spring Replacement, Eject Button Spring: étape 1, image 2 de 2

    • Insert the back of a plastic opening tool into one of the beater holes.

    • Apply force to pull the circular plastic part off.

    • If necessary, use the other side of the plastic opening tool to pry the circular plastic part off.

    Traduire

  2. KitchenAid KHM512ER Eject Button Spring Replacement: étape 2, image 1 de 3 KitchenAid KHM512ER Eject Button Spring Replacement: étape 2, image 2 de 3 KitchenAid KHM512ER Eject Button Spring Replacement: étape 2, image 3 de 3

    • Use a plastic opening tool to remove the speed knob.

    • Use a plastic opening tool to remove the long plastic piece

    • Use a plastic opening tool to remove the speed switch.

    Traduire

  4. KitchenAid KHM512ER Eject Button Spring Replacement: étape 3, image 1 de 2 KitchenAid KHM512ER Eject Button Spring Replacement: étape 3, image 2 de 2

    • Use a Phillips 2 screwdriver to remove the two 20.0mm screws holding the bottom plastic piece on.

    • Your screwdriver may not be long or narrow enough to reach the screws in these holes. If that's the case, use another screwdriver.

    • Remove the bottom plastic piece using a plastic opening tool.

    Traduire

  5. KitchenAid KHM512ER Eject Button Spring Replacement: étape 4, image 1 de 3 KitchenAid KHM512ER Eject Button Spring Replacement: étape 4, image 2 de 3 KitchenAid KHM512ER Eject Button Spring Replacement: étape 4, image 3 de 3

    • Using a Phillips 2 screwdriver, remove the three 20.0mm screws holding the motor assembly in place.

    • Use your hands to remove the motor assembly.

    • Use your hands to hold the eject button from one side while using the other hand to remove the circuit board.

    Traduire

  6. KitchenAid KHM512ER Eject Button Spring Replacement: étape 5, image 1 de 2 KitchenAid KHM512ER Eject Button Spring Replacement: étape 5, image 2 de 2

    • Remove the eject button by pulling it from the inside of the mixer.

    • Hold the eject button firmly while pulling out the spring.

    Traduire
Conclusion

To reassemble your device, follow these instructions in reverse order.

2 autres ont terminé cette réparation.

Auteur

avec 4 autres contributeurs

Yuriy Zaynulin

Membre depuis le 02/10/16

191 Réputation

1 tutoriel rédigé

Badges: 8

+ 5 badges supplémentaires

Équipe

USF Tampa, Team 2-3, Sullivan Spring 2016 Membre de l'équipe USF Tampa, Team 2-3, Sullivan Spring 2016

USFT-SULLIVAN-S16S2G3

3 membres

4 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 0

7 derniers jours : 4

30 derniers jours : 9

Total : 1,572