Réparez vos affaires Communauté Boutique

Levoit Core 300-RAC Fan Replacement

Introduction

A non-functioning fan can significantly reduce your Levoit Core 300-RAC air purifier’s performance. If your device isn’t outputting enough air or the fan isn’t spinning, it may be time to clean or replace it.

This guide demonstrates how to replace the fan. You can also use it to access the fan for cleaning with an air blower and brush. Cleaning the fan may improve performance and help avoid replacement.

Before you begin, ensure the device is turned off and unplugged.

Ce dont vous avez besoin

  1. Levoit Core 300-RAC Fan Replacement, Air Filter: étape 1, image 1 de 2 Levoit Core 300-RAC Fan Replacement, Air Filter: étape 1, image 2 de 2

    • Make sure your device is turned off and unplugged for safety.

    • Turn the Levoit Core 300-RAC over so the bottom is facing up.

    Modifier

  2. Levoit Core 300-RAC Fan Replacement: étape 2, image 1 de 3 Levoit Core 300-RAC Fan Replacement: étape 2, image 2 de 3 Levoit Core 300-RAC Fan Replacement: étape 2, image 3 de 3

    • Turn the bottom cover counterclockwise and lift it off to remove it.

    • The cover does not "snap" on or off when turned.

    Modifier

  3. Levoit Core 300-RAC Fan Replacement: étape 3, image 1 de 3 Levoit Core 300-RAC Fan Replacement: étape 3, image 2 de 3 Levoit Core 300-RAC Fan Replacement: étape 3, image 3 de 3

    • Lift the filter straight up and out of the device.

    Modifier

  4. Levoit Core 300-RAC Fan Replacement, Fan: étape 4, image 1 de 3 Levoit Core 300-RAC Fan Replacement, Fan: étape 4, image 2 de 3 Levoit Core 300-RAC Fan Replacement, Fan: étape 4, image 3 de 3

    • Use a Phillips #2 screwdriver to remove the four screws that secure the gray lid towards the base of the device.

    • Set the screws aside in a safe place.

    Modifier

  5. Levoit Core 300-RAC Fan Replacement: étape 5, image 1 de 3 Levoit Core 300-RAC Fan Replacement: étape 5, image 2 de 3 Levoit Core 300-RAC Fan Replacement: étape 5, image 3 de 3

    • Use a metal spudger or Jimmy to gently pry between the four white tabs and the white housing to release the outer housing.

    • Gently pulling up on the outer housing can prevent the clips from resetting.

    Modifier

  6. Levoit Core 300-RAC Fan Replacement: étape 6, image 1 de 2 Levoit Core 300-RAC Fan Replacement: étape 6, image 2 de 2

    • Remove the outer white housing and set it to the side.

    • The power cord is fed through a hole in the side of this housing, so it has to sit right next to the device.

    Modifier

  8. Levoit Core 300-RAC Fan Replacement: étape 7, image 1 de 3 Levoit Core 300-RAC Fan Replacement: étape 7, image 2 de 3 Levoit Core 300-RAC Fan Replacement: étape 7, image 3 de 3

    • Grab the cable channel by its base, squeeze, and pull up at the same time to remove it.

    Modifier

  9. Levoit Core 300-RAC Fan Replacement: étape 8, image 1 de 2 Levoit Core 300-RAC Fan Replacement: étape 8, image 2 de 2

    • Remove the four Phillips #2 screws securing the gray face plate.

    • Set the screws aside in a safe place.

    Modifier

  10. Levoit Core 300-RAC Fan Replacement: étape 9, image 1 de 3 Levoit Core 300-RAC Fan Replacement: étape 9, image 2 de 3 Levoit Core 300-RAC Fan Replacement: étape 9, image 3 de 3

    • Insert a Jimmy or spudger between the white tab and the gray faceplate body to release the faceplate.

    • Lift it out.

    Modifier

  11. Levoit Core 300-RAC Fan Replacement: étape 10, image 1 de 1

    • Turn your device over so it is upright again.

    Modifier

  12. Levoit Core 300-RAC Fan Replacement: étape 11, image 1 de 3 Levoit Core 300-RAC Fan Replacement: étape 11, image 2 de 3 Levoit Core 300-RAC Fan Replacement: étape 11, image 3 de 3

    • Insert the Jimmy between the gray grille cover and the top of the device.

    • Work your way around the grille cover with the Jimmy to release the clips holding it in place.

    • Take note of the placement of the tabs, as they are keyed and need to go back in the exact way they came out.

    • Remove the grille cover gently as it is connected by a ribbon cable.

    • Be careful not to put too much strain on the ribbon cable as it may break.

    Modifier

  13. Levoit Core 300-RAC Fan Replacement: étape 12, image 1 de 3 Levoit Core 300-RAC Fan Replacement: étape 12, image 2 de 3 Levoit Core 300-RAC Fan Replacement: étape 12, image 3 de 3

    • Squeeze the tab on the connector to release the bundled cable from the control board.

    • The connector should come out fairly easily, do not force it. Pulling too hard could damage the connector.

    Modifier

  14. Levoit Core 300-RAC Fan Replacement: étape 13, image 1 de 3 Levoit Core 300-RAC Fan Replacement: étape 13, image 2 de 3 Levoit Core 300-RAC Fan Replacement: étape 13, image 3 de 3

    • Insert a spudger or Jimmy into the four tabs to release them from holding the outer white housing to the inner black core.

    • Remove the white outer housing.

    Modifier

  15. Levoit Core 300-RAC Fan Replacement: étape 14, image 1 de 1

    • Flip your device over again so the fan is facing up.

    Modifier

  16. Levoit Core 300-RAC Fan Replacement: étape 15, image 1 de 2 Levoit Core 300-RAC Fan Replacement: étape 15, image 2 de 2

    • Use a Phillips #2 screwdriver to remove the three screws on the upper portion of the black housing.

    • Set the screws aside in a safe place.

    Modifier

  17. Levoit Core 300-RAC Fan Replacement: étape 16, image 1 de 3 Levoit Core 300-RAC Fan Replacement: étape 16, image 2 de 3 Levoit Core 300-RAC Fan Replacement: étape 16, image 3 de 3

    • Remove the upper portion of the black housing.

    Modifier

  18. Levoit Core 300-RAC Fan Replacement: étape 17, image 1 de 3 Levoit Core 300-RAC Fan Replacement: étape 17, image 2 de 3 Levoit Core 300-RAC Fan Replacement: étape 17, image 3 de 3

    • Use a 13mm socket wrench with an extension to remove the nut holding the fan in place and remove all hardware from the threaded shaft.

    • There should be a nylon-insert lock nut, a flat washer, and a split ring washer. Set these aside in a safe location.

    Modifier

  19. Levoit Core 300-RAC Fan Replacement: étape 18, image 1 de 3 Levoit Core 300-RAC Fan Replacement: étape 18, image 2 de 3 Levoit Core 300-RAC Fan Replacement: étape 18, image 3 de 3

    • Lift the fan up and off of the threaded shaft.

    • There is another washer underneath the fan, leave it in place for the replacement fan.

    Modifier
Conclusion

To reassemble your device, follow these instructions in reverse order.

Auteur

avec 3 autres contributeurs

Stephen Carrozza

Membre depuis le 11/01/23

241 Réputation

1 tutoriel rédigé

Badges: 3

Équipe

UMass Dartmouth, Team 1-6, Petersen Fall 2023 Membre de l'équipe UMass Dartmouth, Team 1-6, Petersen Fall 2023

UMASSD-PETERSEN-F23S1G6

5 membres

6 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 11

7 derniers jours : 52

30 derniers jours : 181

Total : 2,176