Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.
Ce dont vous avez besoin
-
-
Boîtier fermé, placez l'Unibody à l'envers sur une surface plane.
-
Appuyez sur le côté rainuré du loquet de déverrouillage de la trappe d'accès de manière à saisir l'extrémité libre du loquet. Soulevez le loquet de déverrouillage à la verticale.
-
-
-
Tirez sur la languette et retirez la batterie de votre MacBook.
-
Si la languette n'est pas bien positionnée, elle empêchera la batterie de sortir.
-
-
-
Retirez les huit vis suivantes par lesquelles le boîtier inférieur est fixé au châssis :
-
Une vis Phillips 5,4 mm.
-
Trois vis Phillips 14 mm.
-
Quatre vis Phillips 3,5 mm.
-
-
-
Dévissez les 5 vis suivantes, fixant la paroi interne au boîtier supérieur :
-
Trois vis cruciformes de 10,5 mm.
-
Deux vis cruciformes de 3,7 mm.
-
-
-
Retirez les six vis suivantes fixant le ventilateur droit et le ventilateur gauche à la carte mère :
-
Quatre vis cruciformes de 3,5 mm.
-
Deux vis cruciformes de 3,2 mm.
-
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove eight 8.4 mm Phillips screws securing the heat sink to the logic board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use the tip of a spudger to pry the thermal sensor connector up off the logic board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the two 5 mm Phillips screws securing the left speaker to the logic board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use the flat end of a spudger to pry the left speaker connector up off the logic board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the left speaker assembly out of the logic board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Disconnect the DC-In Board connector from the logic board by pulling it straight away from its socket.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Release the tabs on each side of the RAM chip by simultaneously pushing each tab away from the chip.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
After the RAM chip has popped up, pull it straight out of its socket.
-
Annulation : je n'ai pas terminé ce tutoriel.
58 autres ont terminé cette réparation.
11 commentaires
I have a late 2008, 2.4Ghz, core 2 duo, 15" , unibody, MB470LL/A, MacBook Pro5,1. My current board has the following ports on the left:
Mag safe
Ethernet
FireWire 800
USB (x2)
Mini display port
Mic
Headphone
I just want to verify that any of the boards (2.4, 2.53, 2.66, 2.8, 2.93), will work. I figure as long as I'm replacing the board, why not upgrade CPU and RAM capacity. Any insight would be deeply appreciated!
What did you end up installing?
c cs -
Any advice for someone who stripped a screw each on the fans. I can't get them out.
Original Deutch:
Mein MacBook Pro (MacBook Pro 15" Unibody Late 2008) funktioniert schon länger nicht mehr. Es startete nicht mehr und zeigte, bis auf die Akkuanzeige, keine Lebenszeichen. Vor kurzem habe ich mit einen Reparaturversuch gestartet. Jetzt habe ich das Logic Board vor mir und finde nichts eindeutig beschädigtes. Das einzige was ich sehe ist das die Aufgelötete Batterie kein Saft mehr hat. Ich finde zu dieser jedoch keine Informationen. Mit was tausche ich diese aus?
Google English:
My MacBook Pro (MacBook Pro 15 "Unibody Late 2008) has been running for a while, it stopped booting and showed no sign of life, except for the battery indicator I recently started a repair attempt Now I have the logic board in front of me The only thing I can see is that the soldered battery has no juice left, but I can not find any information about it, so what do I swap it with?