Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.
Ce dont vous avez besoin
-
-
Retirez les huit vis Phillips 4 mm par lesquelles le boîtier inférieur est fixé au MacBook.
-
-
-
Avec l'extrémité plate d'une spatule (spudger), soulevez le connecteur de la batterie de sa prise sur la carte mère.
-
-
-
Retirez les vis suivantes de la grille d'aération arrière, du côté du lecteur optique :
-
Deux vis Torx T8 10 mm
-
Deux vis Phillips 5 mm
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the single 3 mm Phillips screw securing the AirPort/Bluetooth antenna ground strap to the rear speaker.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use the tip of a spudger to pry the AirPort and Bluetooth antenna connectors (3 total) up off the AirPort/Bluetooth card.
-
De-route the long antenna from its channel in the rear speaker housing.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Grab the plastic pull tab secured to the display data cable lock and rotate it toward the DC-In side of the computer.
-
There is also a thin metal lock clip under the plastic tab that has to be released ( Use the tip of a spudger ) before you can disconnect the display data cable.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Gently pull the display data cable connector away from its socket on the logic board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Open your MacBook so the display is perpendicular to the upper case.
-
Place your opened MacBook on a table as pictured.
-
While holding the display and upper case together with your left hand, remove the remaining 7.8 mm with lock washer T8 Torx screw from the lower display bracket.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the last remaining T8 Torx screw securing the display to the upper case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Grab the upper case with your right hand and rotate it slightly toward the top of the display so the upper display bracket clears the edge of the upper case.
-
Rotate the display slightly away from the upper case.
-
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the display up and away from the upper case, minding any brackets or cables that may get caught.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Insert the flat end of a spudger between the thin rubber strip surrounding the front display bezel and the rear display bezel.
-
Use the flat end of your spudger to carefully pry the front display bezel away from the adhesive securing it to the rear display bezel.
-
Continue prying until the front display bezel is free along the right side of the display and behind the right clutch hinge.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use the flat end of a spudger to pry the front display bezel off the top edge of the display assembly.
-
Continue separating until the top edge of the front display bezel is free from the display assembly.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use your spudger to pry the left side of the front display bezel away from the display assembly.
-
Carefully pry up the area behind the left clutch hinge.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Slowly work your way across the lower edge of the front display bezel until it is free from the display assembly.
-
When you get about half way across, pry up from the other side of the front display bezel's lower edge to ease the process.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the front display bezel from the display assembly.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the two 3 mm Phillips screws securing the clutch cover to the rear display bezel.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Insert the flat end of a spudger into the open end of the clutch cover and pry up to release it from the rear display bezel.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the clutch cover from the display assembly.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove following six screws securing the LCD to the rear display bezel:
-
Four 3.4 mm Phillips.
-
Two 3 mm Phillips.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Hold the display vertically and tip it enough to grab the top edge of the LCD and rotate it slightly out of the display assembly, being careful not to break the circuitry off its lower edge.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Peel the piece of tape covering the display data cable connector away from the edge closest to the LCD.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use the tip of a spudger to flip up the thin steel retaining clip securing the display data cable to its socket on the LCD.
-
Pull the display data cable straight away from its socket on the LCD.
-
Lift the LCD out of the display assembly and set it aside.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the two small pieces of black tape securing the display data/camera cable to the rear display bezel.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use the pointed tip of a spudger to pry the camera board off the display assembly.
-
Disconnect the camera cable by pulling its connector away from the socket on the camera board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
De-route the display data/camera cable from the slot cut into the rear display bezel.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Carefully pull the display data/camera cable out from under the frame attached to the rear display bezel and remove it from the display assembly.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the two small pieces of black tape securing the antenna cables to the rear display bezel.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the four 2.3 mm Phillips screws securing the antennas to the rear display bezel.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the single 3.3 mmm Phillips screw securing the lower antenna ground to the rear display bezel.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
De-route the antenna cables from the groove cut into the rear display bezel.
-
Carefully pull the antenna cables out from under the frame attached to the rear display bezel and remove them from the display assembly.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the three Phillips screws securing the center antenna to the rear display bezel.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the center antenna from the rear display bezel.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the three 4.7 mm T6 Torx screws securing the right clutch hinge to the rear display bezel.
-
Remove the right clutch hinge.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the three 4.7 mm T6 Torx screws securing the left clutch hinge to the rear display bezel.
-
Remove the left clutch hinge.
-
Rear display bezel remains.
-
Annulation : je n'ai pas terminé ce tutoriel.
10 autres ont terminé cette réparation.
2 commentaires
Guide is 100% accurate! My friend's macbook lid was cracked and scratched...looked awful. Bought a new one for about $30 and replaced it in under 1 hour for free. Didn't have a spudger, and as I'm sure you all know, you can't buy one at any store that I've found. So, I used a plastic putty knife from lowe's that I got for $0.98, and it worked great! The one thing I have to add is as follows: If your computer is rather old, have some additional adhesive to place on the front LCD bezel. The adhesive does not reapply very well. Double sided 3M tape will work great, but it will be a bit more difficult to remove a second time. Thanks iFixIt! Couldn't have done this without your help.
Anyone know what epoxy is used to secure the metal frame to the plastic cover? It's a green epoxy, but that's all I know. The same green epoxy is also used to secure the top case plastic to the metal frame