Aller au contenu principal

Réparez vos affaires

Droit à la réparation

Boutique

Introduction

This is a step-by-step guide on the PlayStation 2 Slimline SCPH-7500x Clock Battery Replacement, which keeps track of the time within the Playstation 2 when off.

The clock battery is a minor fix for the Playstation and will continue to work without it. It only job is to continue the use of the internal clock once the playstation is off, so when it turns on again, the time will remain accurate.

The process on replacing is a simple 2 step process that will require a Phillips screwdriver, tweezers, and a spudger and requires removing the Outer Shell before staring the guide. Make sure to power off the device and disconnect from any external power source before beginning.

    • Turn off the PlayStation 2 and carefully unplug it from the power source. Also, it is important to eject the CD from the console before flipping the it upside down.

  1. Locate the six feet on the bottom of the PS2.
    • Locate the six feet on the bottom of the PS2.

    • Five of these feet are in plain sight while the last foot is located under the black void sticker on the back of the device.

    • Some versions of the console, such as the PAL Version, may not have this sticker. In this case, the foot or the screw should be in plain sight.

  2. Remove the five visible feet from the bottom of the device using a spudger. Remove the five visible feet from the bottom of the device using a spudger. Remove the five visible feet from the bottom of the device using a spudger.
    • Remove the five visible feet from the bottom of the device using a spudger.

  3. Remove the sticker and then remove the 6th foot. Remove the sticker and then remove the 6th foot.
    • Remove the sticker and then remove the 6th foot.

  4. After all of the feet have been removed,  Use a Phillips #1 screwdriver to remove the six 4.0mm screws from the base of the PS2. After all of the feet have been removed,  Use a Phillips #1 screwdriver to remove the six 4.0mm screws from the base of the PS2. After all of the feet have been removed,  Use a Phillips #1 screwdriver to remove the six 4.0mm screws from the base of the PS2.
    • After all of the feet have been removed, Use a Phillips #1 screwdriver to remove the six 4.0mm screws from the base of the PS2.

  5. Once all of the screws have been removed, pry apart the plastic covers. Start by lifting the side containing the power cable and Ethernet port. Then, lift the opposite side to fully separate the two sides. You may need to apply some gentle force to detach the covers. Be careful not to break the plastic screw pins. You may need to apply some gentle force to detach the covers. Be careful not to break the plastic screw pins.
    • Once all of the screws have been removed, pry apart the plastic covers. Start by lifting the side containing the power cable and Ethernet port. Then, lift the opposite side to fully separate the two sides.

    • You may need to apply some gentle force to detach the covers. Be careful not to break the plastic screw pins.

    It took force to open it, but i broke a plastic pin where the screws enter

    Vasco Mateus - Réponse

    You can use a pick to get the thin edge up without breaking anything.

    Mira Mogzec - Réponse

  6. If done correctly, you should have a fully detached plastic backing, revealing the electronic components of the PlayStation 2.
    • If done correctly, you should have a fully detached plastic backing, revealing the electronic components of the PlayStation 2.

  7. Identify the clock battery, then use tweezers to disconnect the connector from the motherboard. Identify the clock battery, then use tweezers to disconnect the connector from the motherboard. Identify the clock battery, then use tweezers to disconnect the connector from the motherboard.
    • Identify the clock battery, then use tweezers to disconnect the connector from the motherboard.

  8. Gently lift the battery up from the battery compartment using a spudger. Gently lift the battery up from the battery compartment using a spudger.
    • Gently lift the battery up from the battery compartment using a spudger.

Conclusion

To reassemble your device, follow these instructions in reverse order.

3 autre(s) ont terminé cette réparation.

Jared Hirata

Membre depuis le 09/04/2013

600 Réputation

7 tutoriels rédigés

Équipe

Cal Poly, Team 17-4, Regan Spring 2013 Membre de l'équipe Cal Poly, Team 17-4, Regan Spring 2013

CPSU-REGAN-S13S17G4

3 membres

14 tutoriels rédigés

These instructions take for granted how the battery itself should be replaced. I imagine you reconnect the contact with the red wire to the positive side of the CR2032 battery and the contact for the black wire to the negative and wrap electrical tape around the entire thing BEFORE reconnecting it and then following these instructions in reverse order.

Patrick Lewis - Réponse

Ajouter un commentaire

Afficher les statistiques:

Dernières 24 heures : 0

7 derniers jours : 7

30 derniers jours : 30

Total : 2,779