Menu 

Vos paramètres

PlayStation Move Motherboard Replacement

Rédigé par : Destiny Jenkins (et 8 autres contributeurs)
  • Commentaires : 3
  • Favoris : 0
  • Réparations terminées : 1

Difficulté

Modérée

Étapes

16

Sections

2

Drapeaux

2

Needs Better Images

A besoin de meilleures images

De meilleures photos amélioreront ce tutoriel. Aider en proposant de nouvelles photos!

Better Introduction

Meilleure introduction

Améliorez ce tutoriel en complétant ou modifiant l'introduction.

Introduction

Use this guide to replace a faulty Playstation Move Motherboard.

  1. Using a Phillips #0 screwdriver, remove the four 10mm screws from the corners of the trigger button.

    • Using a Phillips #0 screwdriver, remove the four 10mm screws from the corners of the trigger button.

    Traduire

  2. Using a Phillips #0 screwdriver, remove the four 10mm screws located at the back of the device. Using a Phillips #0 screwdriver, remove the four 10mm screws located at the back of the device. Using a Phillips #0 screwdriver, remove the four 10mm screws located at the back of the device.

    • Using a Phillips #0 screwdriver, remove the four 10mm screws located at the back of the device.

    Traduire

  3. Insert the plastic opening tool at the indent along the front and back surfaces of the controller. Gently use a forward and backward motion to safely pop open the cover.

    • Insert the plastic opening tool at the indent along the front and back surfaces of the controller.

    • Gently use a forward and backward motion to safely pop open the cover.

    • Use your hands to further pull it apart and pop it open.

    Traduire

  4. Once the device is opened, lift the battery out of the black plastic holder. Carefully pull the battery out and ensure that it's wires are still connected to the inside.

    • Once the device is opened, lift the battery out of the black plastic holder.

    • Carefully pull the battery out and ensure that it's wires are still connected to the inside.

    Traduire

  5. Using a Phillips head screwdriver, remove the 9mm screw located to the right of the battery, which is connected to the inner plastic frame. Use the plastic opening tool to carefully take out the grey cylindrical piece (vibrator) that is also attached to a wire. Use the plastic opening tool to carefully take out the grey cylindrical piece (vibrator) that is also attached to a wire.

    • Using a Phillips head screwdriver, remove the 9mm screw located to the right of the battery, which is connected to the inner plastic frame.

    • Use the plastic opening tool to carefully take out the grey cylindrical piece (vibrator) that is also attached to a wire.

    Traduire

  6. Gently pull out the small cylindrical grey piece (vibrator). Removing this piece makes it easier to access the wire connection of the battery and remove it.

    • Gently pull out the small cylindrical grey piece (vibrator).

    • Removing this piece makes it easier to access the wire connection of the battery and remove it.

    Traduire

  8. Use tweezers to remove the small piece with a cylindrical top that is located to the left of the inner plastic frame. Use tweezers to remove the small piece with a cylindrical top that is located to the left of the inner plastic frame.

    • Use tweezers to remove the small piece with a cylindrical top that is located to the left of the inner plastic frame.

    Traduire

  9. Use one hand to hold the bottom of the device, and the other hand to squeeze the inner plastic frame. While squeezing the inner plastic frame, pull it up and then pull it towards you to detach it. While removing the frame, be extremely careful because it could damage the frame or the motherboard.

    • Use one hand to hold the bottom of the device, and the other hand to squeeze the inner plastic frame.

    • While squeezing the inner plastic frame, pull it up and then pull it towards you to detach it.

    • While removing the frame, be extremely careful because it could damage the frame or the motherboard.

    Traduire

  10. Gently pull on the end of the red and black wires which is closest to the connector to disconnect the battery. Gently pull on the end of the red and black wires which is closest to the connector to disconnect the battery.

    • Gently pull on the end of the red and black wires which is closest to the connector to disconnect the battery.

    Traduire

  11. Remove the five 1.2 mm screws from upper portion of the controller. If you are replacing the trigger button, continue to step 13. If you are replacing the trigger button, continue to step 13.

    • Remove the five 1.2 mm screws from upper portion of the controller.

    • If you are replacing the trigger button, continue to step 13.

    Traduire

  12. Remove the two 1.2mm Phillips #1 screws. Remove the two 1.2mm Phillips #1 screws.

    • Remove the two 1.2mm Phillips #1 screws.

    Traduire

  13. Cautiously remove the circular white piece at the top without removing the LED inside. Cautiously remove the circular white piece at the top without removing the LED inside. Cautiously remove the circular white piece at the top without removing the LED inside.

    • Cautiously remove the circular white piece at the top without removing the LED inside.

    Traduire

  14. Remove the blue strip that is connected to the trigger button from the motherboard Be careful to gently detach it from the motherboard. The strip may rip if too much strength is applied. Be careful to gently detach it from the motherboard. The strip may rip if too much strength is applied.

    • Remove the blue strip that is connected to the trigger button from the motherboard

    • Be careful to gently detach it from the motherboard. The strip may rip if too much strength is applied.

    Traduire

  15. Remove the trigger button from the controller. Remove the trigger button from the controller.

    • Remove the trigger button from the controller.

    Traduire

  16. Remove the LED light by removing the white strip. If you are replacing the LED light, continue to Step 17. If you are replacing the LED light, continue to Step 17.

    • Remove the LED light by removing the white strip.

    • If you are replacing the LED light, continue to Step 17.

    Traduire

  17. Remove the motherboard from the plastic case. Remove the motherboard from the plastic case.

    • Remove the motherboard from the plastic case.

    Traduire
Conclusion

To reassemble your device, follow these instructions in reverse order.

Une autre personne a terminé cette réparation.

Auteur

avec 8 autres contributeurs

Destiny Jenkins

Membre depuis le 28/09/2016

127 Réputation

1 tutoriel rédigé

Badges: 6

+ 3 badges supplémentaires

Équipe

USF Tampa, Team 3-3, Passmore Fall 2016 Membre de l'équipe USF Tampa, Team 3-3, Passmore Fall 2016

USFT-PASSMORE-F16S3G3

4 membres

4 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Ajouter un commentaire

Afficher les statistiques:

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 8

Total : 599