Utilisez ce guide pour remplacer l'ensemble écran Retina, vitre et caméra iSight.

Ôtez les dix vis suivantes, fixant le boîtier inférieur au boîtier supérieur :
  • Ôtez les dix vis suivantes, fixant le boîtier inférieur au boîtier supérieur :

    • Deux vis Pentalobe de 2,3 mm

    • Huit vis Pentalobe de 3,0 mm

For all the screws you use the P5 pentalobe screwdriver?

Carlos - Réponse

Pentalobe is only for the screws on the bottom cover. The Torx screw driver is for the remainder.

Fredrik -

Is the Pentalobe screwdriver mentioned in the tools list? I did not have one so I used a filed down flat blade screwdriver. Not a fantastic idea, but it works.

Alex Birkett - Réponse

Yes, it's mentioned on the top of this page. P5 Pentalobe to be precise. I didn't have one either, so I bought one from iFixit and that works fantastic. An absolutely precise fit, which is important especially when you might open your MacBook a couple of times during the years you own it. Not using the correct tool might do more harm to the screws than you want! I once had this with a Lenovo Yoga 3 Pro, which has Torx screws (T4 I think) and I used cheap Chinese quality tools, with the result that both the tool and one of the screws are damaged.

addvariety -

the macbook in the picture is 2012. does it has the same structure as 2013?

Edison - Réponse

I never, ever, ever considered using anything but the correct tool on the Pentalobe screws. Too easy to strip and void your warranty (if still in effect), as well as make it almost impossible to get inside later for another upgrade or repair. The Wiha P5 Pentalobe screwdriver fits like a glove and costs only about $11 (a fraction of your drive's price)at Get it!

marketing - Réponse

is P5 supposed to be for all 10 screws? it works on the 2x 2.3mm at the top, but not for the 8x others for me. what size screwdriver for the 3mm? thanks

monsieurescargot - Réponse

Yes, the p5 works for all 10 pentalobe screw heads for bottom cover. The the different size mm reference only refers to the difference in length of the screws, but again both heads are p5.

Antoine Thornton - Réponse

Mettez vos doigts entre le boîtier inférieur et le boîtier supérieur.
  • Mettez vos doigts entre le boîtier inférieur et le boîtier supérieur.

  • Séparez avec précaution les deux boîtiers et retirez le boîtier inférieur.

Ajouter un commentaire

  • Le boîtier inférieur est connecté au boîtier supérieur par deux attaches en plastique au milieu.

  • Lors du remontage, appuyez doucement sur le milieu du boîtier inférieur pour que les deux attaches s'enclenchent à nouveau.

There are two screws that are shorter-they go to the back near the vent.

wrbandllm - Réponse

This was already mentioned at the start, it says 2x 2.3mm screws and those are coloured red instead of orange for the other ones in iFixit's image.

addvariety - Réponse

What is the black vinyl-y sticker on the inside of the case (some sort of shield?). I was forced to slightly puncture it in order to replace the feet on my laptop. Thanks in advance.

Tommy Huang - Réponse

  • Si nécessaire, retirez le cache en plastique couvrant la carte de contact de la batterie.

Do you know where I can purchase this plastic cover? Mine is missing and no one will work on my computer without it.

jodieabc - Réponse

  • Avec l'extrémité plate d'une spatule (spudger), tirez le connecteur de la batterie tout droit hors de sa prise sur la carte mère.

  • Assurez-vous de faire levier uniquement sur le connecteur et non pas sur sa prise, sinon vous risquez d'endommager irréversiblement la carte mère.

I have a friends MacBook Pro that has some water damage that caused the MacBook not to be able to use battery power, but still work when plugged into A/C. Upon further inspection I can see visible corrosion on a few of the 9 cables going from the battery connector to that small circuit board. Is it possible to just replace that circuit board?

jramsey21 - Réponse

I have the some problem. I was thinking to replace the whole battery but I am not it will solve the problem. Any suggestions?

salvatorebarbera -

Sometimes it can be enough to just clean the contacts without having to replace the entire board. Dosent work for complicated IC's like plcc type, where corrosion is underneath the chip. Here you will have to reheat and reapply the IC.

andrehedegaard -

Have either of you replaced the battery and/or circuit board to fix the MacBooks with the water damage ? I have the same problem with the MacBook working fine when connected to power but dying immediately when the power cord is removed.

Steve - Réponse

Hi, Steve. I had the same problem: Macbook Pro 15 retina with coffee damage. And it worked fine when connected to power. I made it working after replacing the whole battery. It seems that circuit connected to the battery becomes disabled to prevent short circuit.

Vadim Gribanov -

When placing the battery connector back into the socket on the logic board, check that every part of connector is pressed down. You should hear a soft click when it's back in place.

Ethan Tarquin - Réponse

Thanks for the comment. My MBP isn’t powering on after I walked through these steps, and I assume it is because the battery connector isn’t fully connected. (I can’t check yet since I borrowed the pentalobe screwdriver)

Caleb Steinborn -


I thought I made sure it was connected but when running the computer it only detected the battery but couldn’t power it. I had to run with power adapter. Also it didn’t charge. I guess some pins were connected but not all. To verify that all were connected I removed the plastic cover, placed it carefully completely flat, and then reattached the plastic cover. After that it worked!

Jonas Ehrs -

If I only want to replace the trackpad cable, then which steps should I skip? This step seems unnecessary

Parth Gudhka - Réponse

  • Pliez le connecteur de la batterie vers le haut afin d'éviter tout contact accidentel avec la prise pendant la réparation.

If you miss or let this step for later like I did, the power left in the battery even though the computer is completely shut down, will screw up the I/O board cable like I did. I noticed this after I put all the pieces back, turn the computer on and surprise, no wifi hardware is detected. -.-

sebasgaes - Réponse

I put a small piece of blue painters tape on the battery connector contacts to prevent it from accidentally making a connection and shorting. This helped keep things a bit more protected.

LaymanLab - Réponse

That’s a great idea!

David Lilliebridge - Réponse

I used a small piece of paper to prevent the connector from connecting, no need to wrestle with even low-stick adhesive.

dbrick - Réponse

  • Retirez délicatement la protection en caoutchouc du bord du dissipateur de chaleur.

  • La protection s'enroulle autour du dissipateur thermique et s'insère dans les fentes du conduit de ventilateur. Lors du remontage, assurez-vous d'insérer les languettes dans les encoches du conduit.

Ajouter un commentaire

  • Insérez la pointe d'un spudger sous chacun des câbles d'antenne près de leur connecteur et soulevez-les pour les débrancher de la carte AirPort.

  • Les trois câbles correspondent à des manchons noirs de différentes longueurs. Lors du remontage :

    • Connectez le câble au manchon long à la prise centrale.

    • Le câble au manchon court se connecte à côté de la vis.

    • Le câble restant n'a pas de manchon et se connecte à la dernière prise vide, à côté du ventilateur.

I struggled with reconnecting these, and in the process accidentally ripped the connector away from the wire. Is there anything I can do to reattached it?

Vanessa schroll - Réponse

This is most difficult and time consuming portion of this entire procedure. Make sure to lift the connectors straight up - not to damage them. The reconnection of the contacts may take several tries. USE CARE AND BE PATIENT! You will eventually get them to connect.

Darius - Réponse

does anyone have advice on what is the best tool to use for reconnecting? this is definitely the hardest step to reassembly

M N - Réponse

When reassembling, I used tweezers to line them up and the spudger to push them down.

Joshua Johnson - Réponse

thank you Joshua, this helped me get them. they do take a bit of patience but it’s worth taking your time.

Kevin Lynch -

everything else was easy... I still haven't managed to figure this step out... good luck in your repair

M N - Réponse

I got it! line the wire up; push the top part of the metal and give it firm pressure; they should snap in and connect

M N - Réponse

You'll get 'em in. Work gently. Make sure they're exactly over top the bottom pins. Press down with a flat smudger. It took me a lot of gentle work to get them in.

Kent - Réponse

I saw the sleeves on these.. and when looking at the replacement display saw they matched exactly and took the chance it was intentional. The only thing that got me.. was the bottom panel screws.. didn't know there were 3 types.. (should have known though, I mean right?! LOL Apple (rolls eyes) They could do like Samsung and use one screw for everything.. but oh no.. there is some OCD engineer that just likes SCREWING with people!

Tim - Réponse

Pro Tip: When reassembling, do not screw on the metal tab attached to these connectors (part of step 15) until after you have all 3 connected. This gives you uninhibited range of motion for the 3 wires. Go slow as other commenters have said. Start with the shortest wire first. Once all 3 are connected, screw on the metal tab with those 2 screws. Finally double check that all 3 are still connected.

D B - Réponse

  • Utilisez la pointe d'un spudger pour appuyer de chaque côté du connecteur de la nappe de la caméra iSight, pour la faire sortir de sa prise sur la carte mère.

Ajouter un commentaire

  • Décollez la nappe de la caméra iSight du boîtier du ventilateur.

Ajouter un commentaire

  • Prenez la languette en plastique noir pour ouvrir le connecteur de la nappe de l'écran et tirez-le tout droit hors de sa prise sur la carte mère.

  • Pendant la réinstallation, assurez-vous de remettre correctement la languette du connecteur de la nappe de l'écran.

This is pulled straight out to the side of the Macbook, not up.

nmackaron - Réponse

Thanks for adding this comment !

jrbhome - Réponse

Please use a nylon black stick to lift the lock bar up and push the connection apart reason being is the lock bar should not be pulled on and by pulling on it like shown may cause damage to the MLB/DISPLAY connection and then you’re into not just a display repair but a MLB on top of it!!!

Dutchie - Réponse

hello, im trying to do this because im experiencing a blackscreen problem. Id like to do this but my macbook looks so different than this one. Could anyone help me?

Karla Díaz - Réponse

If it doesn’t look like this, you’re looking at the wrong guide.

maccentric -

  • Retirez les caches de charnière en caoutchouc des charnières à droite et à gauche de l'écran.

Ajouter un commentaire

  • Retirez les deux vis Torx T5 de 4,2 mm fixant les supports de charnière en aluminium de chaque côté du Macbook.

I found these to be very tight and wasnt able to move them with the ifixt screwdriver kit, i had to get a t-handle torx 9 bit to move them

harveyhalfpint - Réponse

Yes they were tight but I managed to shift them with the iFixit screwdriver set

Steven Fillingham - Réponse

This is 1 screw on each side (not 2 on each side). They are circled in red.

nmackaron - Réponse

The T5 in the set I bought from was too big and started to strip these screws. Got an Ace Hardware brand one instead and it worked great.

Brian Hultin - Réponse

  • Utilisez une paire de pincette pour retirer les supports de charnière en aluminium des charnières à droite et à gauche de l'écran.

  • Lors du remontage, la partie verticale du support et le rail en aluminium au centre du Macbook doivent être alignés.

Ajouter un commentaire

  • Retirez les quatre vis Torx extérieures T8 de 5,3 mm (deux de chaque côté) fixant l'écran au boîtier supérieur.

    • Certains modèles peuvent avoir des vis Torx T9 au lieu de T8.

Does these three screws are the same size? Can i mix use these screws during the installing process?

Michael Kwok - Réponse

On my model, there was a thin piece of translucent plastic covering the left-side outer screws. It peeled off easily. It must be replaced upon reassembly. When removing these two (left-side) screws, a metal assembly securing the antenna wires was released below the screws. It must be replaced before reassembling these two screws.

Ralph Begleiter - Réponse

  • Ouvrez le MacBook Pro d'un peu plus de 90 degrés et posez-le debout sur la table, comme illustré.

  • Tout en maintenant l'écran de votre main gauche, retirez la vis T8 Torx restante du support supérieur de l'écran.

  • Assurez-vous que l'écran et le boîtier supérieur sont stables et ne risquent pas de tomber, ce qui pourrait endommager chaque composant.

  • Retirez la dernière vis Torx T8 restante fixant l'écran au boîtier supérieur.

Ajouter un commentaire

  • Saisissez le boîtier supérieur de votre main droite et tournez-le légèrement dans le sens des aiguilles d'une montre, vers le haut de l'écran de façon à séparer les supports de l'écran du bord du boîtier supérieur.

  • Faites pivoter légèrement l'écran pour l'écarter du boîtier supérieur.

  • Éloignez l'écran du boîtier supérieur, en faisant attention aux dispositifs de fixation et aux nappes, qui pourraient rester accrochés.

When replacing the display assembly with a new one, the new hinges may be very hard to move into the 90 degree position. We found it helpful to loop a paperclip into the screw hole of the hinge to facilitate pulling open the hinge.

Eric - Réponse

Yes also found the hinges to be extremely tight, could not move them with from their initial position with fingers, ended up using a pair of pliers to rotate them enough to get fingers under them

Steven Fillingham - Réponse

Are there any cheaper replacement screens? If so I need to know. My parents still haven't found out and I don't make a ton of money...

Haley Hildreth - Réponse

The paper clip is a great tip. I also used the spudger flat end under the hinge and the metal side of the case as leverage to push it up.

D B - Réponse


Pour réassembler votre appareil, suivez ces instructions dans l'ordre inverse.

97 autre(s) ont terminé cette réparation.

Merci à ces traducteurs :


Ces traducteurs nous aident réparer le monde ! Vous voulez contribuer ?
Commencez à traduire ›

Andrew Optimus Goldberg

Membre depuis le 17/10/2009

379 671 Réputation

1 308 tutoriels rédigés


iFixit Membre de l'équipe iFixit


109 membres

6 232 tutoriels rédigés

25 commentaires

Just did this for my wife. Awesome! Thank you!

Josh Way - Réponse

Just complete this over lunch and it was cake - no pun. Follow the instructions and you'll be back to new in about 30 minutes. The toughest part is getting all those little screws out, so be patient and just know it's worth the squeeze. Take care, AZ

Advisor King - Réponse

Is display assembly for Late 2013/Mid 2014 compatible with this model?

Payton James - Réponse

Hi, I have same question, and I think its not fully compatible, I tried to put 2014 display on 2015 and its have issue with backlight at startup, for example if you press "ALT" at startup to chose startup disk, screen remains all the time dark only with flash light you can see its working and if you chose disk and only after some 5 seconds backlight will turn on, if I put old original broken display but with working backlight it will turn on backlight straight with the "chime" and yes with new 2014 display its not lighting up straight after chime only after some 5 seconds or so, but after that works fine.

artc -

Hi, last night i was watching a movie in my MBP E2015, and out of nothing, gave me "the gift" of a black screen... i tried everything i found in forums, reset SMC PRAM/NRAM, safe mode, force reboot, well, you name it, i tried it with no luck... i opened the MB and re-connected the display cable to what see if something happens, and nothing... i can only see the contents of the screen when using HDMI on a tv (i also can see stuff in the screen when pointing a flashlight in the dark screen, that makes me think its fixable) should i start thinking of replacing the whole display? any suggestion would be appreciated, thanks!


Daniel Dugarte - Réponse

Hi Daniel,

I am having the same problem, did you find a solution yet?


Jaymes Milner -

That usually means that the backlight on your display has broken, so the 'screen' part is still receiving an input from the computer, but the light behind it that makes the screen bright enough for you to see it, has broken. So, either it is a loose connection for the backlight, or the whole backlight is dead. If the latter is true, the whole display component must be replaced.

Dominic Rogers -

Hi Daniel, what did you do to fix it? Any help would be appreciated thanks! :)

Srujana -

How skilled do you have to be to do this repair?

Anay Bhakat - Réponse

It does say moderate difficulty, however in all honesty it's pretty easy if you know how to go slow, keep track of screws, and not force anything. Of course, helps to have experience inside the MacBook to know your way around, too, but I'd say that's probably not necessary :)

Nathanael Bunge -

Is the screen or displays connection to the graphics the same as the 2015 13" Macbook Air?

Nate - Réponse

I think the answer is a firm NO but is it possible to replace a cracked early 2015 MBP retina screen with a late 2011 non-retina screen? Thanks!

Jacob Kaucher - Réponse

I had two machines, one that wouldn't power on but the screen was fine, and one that had a cracked screen but booted up fine. Tried swapping the displays and couldn't get the good unit to power on at all. Tried swapping back to the broken display, and still can't get the unit to power on. Now I've got two machines that won't power on. Anyone need a couple paperweights? ;-)

Nathan Beranger - Réponse

Just used these instructions to replace my screen and it went perfect. Couldn't be happier.

Derik Hammes - Réponse

Perfect! Replacing the display was such a breeze, just saved a ton on money.

Kartavya Sharma - Réponse


Spilled a small amount of wine on my keyboard a while back and did the usual, turn it off and upsidedown etc and it was fine.

A couple of weeks later it bagan to flikker from time to time. Oddly enough the flicker speed would change in conjunction with the keyboard backlight streangth so i assumed there was a short somwhere on the logicboard due to some sugar gunk somwhere. I opened it and cleaned all the gunk i could find but it didnt help. Looks pristene again now (to the eye obv.).

A couple of days ago a new behaviour: Now if i leave it off or closed for a long time the screen comes on and works for about 25 mins. If i close it and reopen it works for a period of time related to how long it was closed. I'm totally baffeled, maybe something to do with a capasitor charging? Above my paygrade.

The last thing i can think to do myself is change the LVDS cable, but from this it looks like its embedded in the monitor. Is there a way to do it without buying a new screen?

Sorry for life story. Thanx!

james Trickey - Réponse

the Apple cracked and when I went to open my MacBook the screen it’s self is fond however the imaging is lined out. When I plug a monitor in I can see the what I am doing. Because the screen isn’t cracked does this mean I have to get an new screen and assembly?

Kay Sachs - Réponse

Can any body tell me that parts assembly unit includes ?

such as camera, wifi etc ??

Shahid Amin - Réponse

i handed over my machine to istore for replacement of display unit. so i want to know what i need to check when they will return my machine to me ?

Shahid Amin - Réponse

Wi-Fi, camera (and camera light ofc) and display (that the screen works)

Edvard Schreiner Sjøblom -

Thank you so much for this. I was quoted 400 euro to get a replacement screen fitted. I located one online and assembled it myself with help from your guide. Thank you for the help.

Kevin Lynch - Réponse

I just did this! It was terrifying but not too difficult. For sections that I struggled on, reading the individual comments for each step helped. New display is beautiful!

Lauren Mata - Réponse

Just replaced my display using your guide. It was a breeze! Thanks soooo much!

RASTAGURL1 - Réponse

Worked for me, thanks!

Isaac Ellmen - Réponse

Excellent Guide!

Rudolph Wood - Réponse

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 74

7 derniers jours : 511

30 derniers jours : 2,478

Total : 69,089