Aller au contenu principal

Introduction

Veillez à éteindre complètement votre Moto X4 avant de sortir votre iOpener pour ouvrir le téléphone.

  1. Cette étape n’est pas traduite. Aidez à la traduire

    Before you begin, turn off your phone. Heat an iOpener and apply it to the left edge of the phone for two minutes.
    • Before you begin, turn off your phone.

    • Heat an iOpener and apply it to the left edge of the phone for two minutes.

    • You may need to reheat and reapply the iOpener several times to get the phone warm enough. Follow the iOpener instructions to avoid overheating.

    • A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the phone—the display and internal battery are both susceptible to heat damage.

    • As you wait, take note of the the following areas:

    • Display cable—be careful not to slice too deeply near the edge here, or you may damage the display cable.

    • Fingerprint sensor cable—be careful not to slice too deeply near the edge here, or you may damage the fingerprint sensor cable.

  2. Cette étape n’est pas traduite. Aidez à la traduire

    Apply a suction cup to the screen, as close to the heated edge as possible. Pull on the suction cup with strong, steady force to create a gap in the seam. Insert the point of an opening pick into the gap.
    • Apply a suction cup to the screen, as close to the heated edge as possible.

    • Pull on the suction cup with strong, steady force to create a gap in the seam.

    • Insert the point of an opening pick into the gap.

    • Depending on the age of your phone, this may be difficult. If you are having trouble, apply heat to the edge and try again.

  3. Cette étape n’est pas traduite. Aidez à la traduire

    Slide the opening pick along the edge to slice through the adhesive. Leave an opening pick in the seam to prevent the adhesive from re-sealing. Leave an opening pick in the seam to prevent the adhesive from re-sealing.
    • Slide the opening pick along the edge to slice through the adhesive.

    • Leave an opening pick in the seam to prevent the adhesive from re-sealing.

  4. Cette étape n’est pas traduite. Aidez à la traduire

    Heat the top edge of the phone with an iOpener. Carefully slice around the corner and through the top edge to separate the adhesive. Carefully slice around the corner and through the top edge to separate the adhesive.
    • Heat the top edge of the phone with an iOpener.

    • Carefully slice around the corner and through the top edge to separate the adhesive.

  5. Cette étape n’est pas traduite. Aidez à la traduire

    Heat the screen's right edge with an iOpener. Be careful not to slice too deeply near the cables to avoid damaging them. Use an opening pick to slice along the right edge to separate the adhesive.
    • Heat the screen's right edge with an iOpener.

    • Be careful not to slice too deeply near the cables to avoid damaging them.

    • Use an opening pick to slice along the right edge to separate the adhesive.

  6. Cette étape n’est pas traduite. Aidez à la traduire

    Repeat the previous steps to heat and slice the bottom edge of the phone. Repeat the previous steps to heat and slice the bottom edge of the phone.
    • Repeat the previous steps to heat and slice the bottom edge of the phone.

  7. Cette étape n’est pas traduite. Aidez à la traduire

    Do not try to remove the screen yet—it is still attached to the phone by delicate flex cables. Carefully lift up the left edge of the screen and cut away remaining adhesives with an opening pick.
    • Do not try to remove the screen yet—it is still attached to the phone by delicate flex cables.

    • Carefully lift up the left edge of the screen and cut away remaining adhesives with an opening pick.

  8. Cette étape n’est pas traduite. Aidez à la traduire

    Swing open the screen and prop it up with a small box as you work on disconnecting the flex cables.
    • Swing open the screen and prop it up with a small box as you work on disconnecting the flex cables.

    • During reassembly, this is a good time to power on your phone and test all functions before sealing it up. Be sure to power your phone back down completely before you continue working.

  9. Cette étape n’est pas traduite. Aidez à la traduire

    Slide the point of a spudger underneath the fingerprint sensor cable and gently pry up to loosen the cable from the phone. Do not pull on the cable. It is still attached to the phone by a delicate ZIF socket.
    • Slide the point of a spudger underneath the fingerprint sensor cable and gently pry up to loosen the cable from the phone.

    • Do not pull on the cable. It is still attached to the phone by a delicate ZIF socket.

  10. Cette étape n’est pas traduite. Aidez à la traduire

    Use the point of a spudger to flip up the lock bar on the fingerprint sensor's ZIF socket, near the bottom right of the phone. Use tweezers to carefully slide the fingerprint sensor cable out of the socket. Use tweezers to carefully slide the fingerprint sensor cable out of the socket.
    • Use the point of a spudger to flip up the lock bar on the fingerprint sensor's ZIF socket, near the bottom right of the phone.

    • Use tweezers to carefully slide the fingerprint sensor cable out of the socket.

  11. Cette étape n’est pas traduite. Aidez à la traduire

    Use an opening tool to flip up the wide lock bar on the display cable's ZIF socket, near the top right of the phone. Use tweezers to carefully slide the display cable out of the ZIF socket. Use tweezers to carefully slide the display cable out of the ZIF socket.
    • Use an opening tool to flip up the wide lock bar on the display cable's ZIF socket, near the top right of the phone.

    • Use tweezers to carefully slide the display cable out of the ZIF socket.

  12. Cette étape n’est pas traduite. Aidez à la traduire

    Remove the screen. During reassembly, follow this guide to clean the existing adhesive off and install custom-cut adhesives for your phone.
    • Remove the screen.

    • During reassembly, follow this guide to clean the existing adhesive off and install custom-cut adhesives for your phone.

  13. Cette étape n’est pas traduite. Aidez à la traduire

    Apply a heated iOpener to the fingerprint sensor for one minute to soften the adhesive gasket.
    • Apply a heated iOpener to the fingerprint sensor for one minute to soften the adhesive gasket.

  14. Cette étape n’est pas traduite. Aidez à la traduire

    Slide the point of a spudger under the fingerprint sensor cable and gently pry to loosen the cable from the screen. Slide the point of a spudger under the fingerprint sensor cable and gently pry to loosen the cable from the screen.
    • Slide the point of a spudger under the fingerprint sensor cable and gently pry to loosen the cable from the screen.

  15. Cette étape n’est pas traduite. Aidez à la traduire

    Use an opening tool to pry up and loosen the fingerprint sensor from the screen. Use an opening tool to pry up and loosen the fingerprint sensor from the screen.
    • Use an opening tool to pry up and loosen the fingerprint sensor from the screen.

  16. Cette étape n’est pas traduite. Aidez à la traduire

    Remove the fingerprint sensor.
    • Remove the fingerprint sensor.

    • To reattach the fingerprint sensor, use a precut gasket, or apply some thin strips of Tesa adhesive to the perimeter of the sensor.

  17. Cette étape n’est pas traduite. Aidez à la traduire

    If your replacement screen did not come with an earpiece speaker grille, you will have to transfer it from your original screen. The earpiece speaker grille consists of two small mesh pieces. Be careful not to lose them as you transfer them over. Use the flat edge of a spudger to push the grille from the front side of the screen to loosen it from its recess.
    • If your replacement screen did not come with an earpiece speaker grille, you will have to transfer it from your original screen.

    • The earpiece speaker grille consists of two small mesh pieces. Be careful not to lose them as you transfer them over.

    • Use the flat edge of a spudger to push the grille from the front side of the screen to loosen it from its recess.

    • Remove the grille.

    • Use some thin strips of Tesa tape to affix the grille to the replacement screen.

  18. Cette étape n’est pas traduite. Aidez à la traduire

    If your replacement part did not come with a lower microphone gasket, use tweezers to carefully peel it from your old screen and transfer it to your replacement part.
    • If your replacement part did not come with a lower microphone gasket, use tweezers to carefully peel it from your old screen and transfer it to your replacement part.

    • Compare your new replacement screen to the original part. You may need to transfer remaining components or remove adhesive backings from the new part before installing.

Conclusion

Pour remonter votre appareil, suivez ces instructions en sens inverse.

19 autres ont terminé cette réparation.

Merci à ces traducteurs :

en fr

0%

Claire Miesch nous aide à réparer le monde ! Vous voulez contribuer ?
Commencez à traduire ›

Arthur Shi

Membre depuis le 03/01/2018

177 945 Réputation

429 tutoriels rédigés

Équipe

iFixit Membre de l'équipe iFixit

Community

139 membres

15 645 tutoriels rédigés

6 commentaires

This guide really only covers screen removal, and should detail replacing the screen as advertised. Here are a few more steps that should be added:

1. Transferring old hardware to the new screen (seals, filters, fingerprint sensor, & the grey carbon mat.

2. Cleaning up old adhesive.

3. Applying new adhesive, whether it’s the one-piece that ifixit carries (recommended), or Tesa tape.

4. Installing the new display assembly

Andrew Parker - Réponse

Is it possible to remove and replace only the glass? Can I do that without removing the whole LCD screen and avoid disconnecting/reconnecting wires?

Drew S - Réponse

Hi Drew,

I haven’t tried, but I think it is possible to do a glass-only repair for this LCD screen, as long as you have the necessary tools and bonding adhesives. You would still have to deal with the fingerprint sensor, which is sealed onto the glass.

Arthur Shi -

I noticed the fingerprint sensor not being quite as low on the right edge after this. Also, I think it has a bit of “give” now when I press on it with a thumbnail. If the tips of my thumbs weren't so dry right now I might not have noticed, though.

Chris Young - Réponse

I just finished following your guide and mostly satisfied. Somehow my fingerprint sensor doesn’t work but <shrugs> If I loose that convenience for a time, then I still payed less and got experience. Now, for the constructive criticism. YOU NEED a re-assembly guide. We’re not all at the level you guys are and it took a lot more work for me to put things back together as I had to flip things around and watch a few other videos to see steps I missed. You need a guide because you some of the items you’re supposed to use are not mentioned here because they’re not used until you re-assemble it. Please add it to this guide (for future people) unless you’re going to stop selling this kit, then just add it to the other kits. It would be a great help.

Ben - Réponse

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 5

7 derniers jours : 35

30 derniers jours : 137

Total : 14,104