Aller au contenu principal

Introduction

Utilisez ce tutoriel pour remplacer le haut-parleur droit.

Ce tutoriel est destiné au haut-parleur situé sur le côté droit de votre ordinateur portable. Pendant une bonne partie du tutoriel, il sera sur votre gauche, car l'ordinateur portable sera à l'envers.

  1. Ôtez les dix vis suivantes, qui fixent le boîtier inférieur au boîtier supérieur :
    • Ôtez les dix vis suivantes, qui fixent le boîtier inférieur au boîtier supérieur :

    • Deux vis Pentalobe P5 de 2,3 mm

    • Huit vis Pentalobe P5 de 3,0 mm

    • Tout au long de cette réparation, prenez note de l'emplacement de chaque vis, et assurez-vous qu'elle retrouvera sa place initiale pour éviter d'endommager votre appareil.

    For all the screws you use the P5 pentalobe screwdriver?

    Carlos - Réponse

    Pentalobe is only for the screws on the bottom cover. The Torx screw driver is for the remainder.

    Fredrik -

    I never, ever, ever considered using anything but the correct tool on the Pentalobe screws. Too easy to strip and void your warranty (if still in effect), as well as make it almost impossible to get inside later for another upgrade or repair. The Wiha P5 Pentalobe screwdriver fits like a glove and costs only about $11 (a fraction of your drive's price)at Amazon.com. Get it!

    marketing - Réponse

    I followed this exactly and was able to replace my broken trackpad. I did not have to replace the ribbon OR the battery. However I would suggest getting the ribbon since it’s fairly cheap, as for the batteries I was able to do it with a card only. I didn’t use any heat or the liquid but it takes some time. You really have to work the card in there to release the glue. Also you must be very careful not to bend the batteries or damage them, if you do you must replace with new. This took me about 1.5hrs and my computer works like new. Apple cost for this job was around $450, I did it for $120. Big ups to ifixit for this awesome tutorial, tool set and parts!

    On a side note, only use quality tools, the cheap ones will break or strip the screws.

    Dustin Steward - Réponse

    Note that the eight 3mm screws have a shoulder under the head, while the two 2.3mm screws are “full thread”, i.e., there is no shoulder under their heads. It’s important to put the two screws with no shoulder at the hinge of the cover.

    All ten screws require a P5 Pentalobe screwdriver, preferably with a magnetized tip to help hold and position the screw.

    All of the screws have blue “Loctite” thread locker compound on their threads. This is to help prevent the screws from working loose and falling out. Don’t attempt to clean the Loctite from the screws — leave it in place, and it will continue to help prevent the re-inserted screws from working loose.

    When replacing the bottom cover, it is a good technique to insert and BEGIN tightening all ten screws BEFORE fully tightening any one screw. After all the screws have been started, then go around and finish tightening all of them. By doing this, you make it easier to feel that each screw has been started properly, and is not “cross-threaded”.

    doubleclutch - Réponse

    This is what I found on my MBP mid-2014 13” Retina. All 10 used the same screwdriver. I didn’t see the blue “loctite” but I also got my computer refurbished.

    Evan Shulman -

    A good technique for starting to thread the screws when replacing them is to position and align the screw, and with the driver, gently turn the screw in the REMOVAL direction until you feel and hear a slight click. This click happens when the leading thread of the screw drops off of the leading edge of the thread in the hole — this is the point at which the threads are properly positioned for engagement. You can now turn the driver and screw in the TIGHTENING direction. This technique will help prevent accidental “cross-threading” of the screw, which will damage the threads permanently.

    Note that this is a useful technique when installing ANY threaded fastener.

    doubleclutch - Réponse

    Hi peeps,

    I have a wifi problem on this MBP 13” early 2015 and was pleasently surprised to find your guide to changing the airport card.

    However upon closer inspection it seems that on my MBP (purchased new or so I thought) the 3 antennae seem so have been soldered together at the point where they are clamped to the chassis. I have photos but cannot post here. Can anyone conform that where the 3 antennae wires are held to the chssis by the 2 scew metal support (just before disappearing into the screen hinge), the support is not meant to short the 3 wires together. This makes no sense for 3 seperate antennae wires.

    Any advice /close up photos is welcome here.

    dom

    colonel mustard - Réponse

    Tip: Use post-it notes to keep track of screws

    1. Pack of post it notes

    2. Stick screws to the sticky part of the post it note

    3. Write on the post it note which step and what kind of screw it is

    ibash - Réponse

    Hi, in order to drain the battery I am running:

    yes > /dev/null

    in 4 terminals, so the CPU maxes out at almost 99%.

    I hope this speeds up the battery draining process.

    And the backlight is at maximum brightness :-)

    You can see the cpu load in Activity Monitor.

    Its draining at 20% per 15 minutes.

    Any concerns about draining the battery in this way?

    Andre van der Ham - Réponse

    Something I’ve been curious about, is it possible to upgrade a late 2013 Retina model MacBook Pro, with the improved 16gb ram and i7 processor logic board from the 2015 retina model? I’d be interested to try but not ready to shell out the $500+ to be the first lol

    Chat Dawgie - Réponse

    Without rehashing what others have said, I would highly recommend reading through the steps *and* the comments for each before tackling your replacement for tips. Highlights for me were: only disconnecting what actually needed to be disconnected, rotating the spudger to release the track pad cable, a hair dryer worked perfectly fine, and the pencil outline of the battery before you remove. You got this!

    N DesRochers - Réponse

  2. Glissez vos doigts entre le boîtier inférieur et le boîtier supérieur.
    • Glissez vos doigts entre le boîtier inférieur et le boîtier supérieur.

    • Séparez avec précaution les deux boîtiers, soulevez et retirez le boîtier inférieur.

    This takes a bit more effort than you might expect. Put your fingers where shown and lift about 3inches. With enough upwards pressure the plastic holders will “pop free” and the bottom will come off easily.

    hamiltont - Réponse

    To reattach bottom case I found it helpful to line fingers up with clips under case should snap easily

    Peter Stoll - Réponse

    If your old battery has swollen, the lower case may “pop” open. Don’t lose your screws!

    Maxine Loveman - Réponse

  3. Le boîtier inférieur est attaché au boîtier supérieur par deux attaches en plastique au milieu. Lors du remontage, appuyez doucement sur le milieu du boîtier inférieur pour que les deux attaches s'enclenchent à nouveau.
    • Le boîtier inférieur est attaché au boîtier supérieur par deux attaches en plastique au milieu.

    • Lors du remontage, appuyez doucement sur le milieu du boîtier inférieur pour que les deux attaches s'enclenchent à nouveau.

    This wording I found quite confusing. They just mean when putting the lid back on that you just removed in the previous step, push here.

    Mmm ttt - Réponse

    I took my pointer and thumb (which are luckily long enough) to feel where the studs are on the back panel, and then as I put the back panel back on, I pushed in the spot I had marked with my fingers to ensure I was applying pressure only on this part.

    Evan Shulman - Réponse

  4. Si nécessaire, retirez le cache en plastique couvrant la carte de contact de la batterie.
    • Si nécessaire, retirez le cache en plastique couvrant la carte de contact de la batterie.

    A plastic foam cover also covers plug and socket and the whole battery. It is easy to remove it from the right side to the trackpad wire that the battery plug is free like shown in the picture. I kept it to use it again later.

    Daniel Brehm - Réponse

    I have done tons of these battery replacements.

    You don’t need to do anything on the list after you disconnect the battery, apart from carefully moving the speakers out of the way, and then prise up the battery modules. I just very carefully, and with little even motions, use a large slot screwdriver. Being careful to keep it flat, to not puncture the battery.

    Easy peasy. I have never had an issue after dozens of the tasks…

    davelarose - Réponse

  5. Avec l'extrémité plate d'une spatule (spudger), tirez le connecteur de la batterie tout droit hors de sa prise sur la carte mère. Assurez-vous de faire levier uniquement sur le connecteur et non pas sur sa prise, sinon vous risquez d'endommager irréversiblement la carte mère.
    • Avec l'extrémité plate d'une spatule (spudger), tirez le connecteur de la batterie tout droit hors de sa prise sur la carte mère.

    • Assurez-vous de faire levier uniquement sur le connecteur et non pas sur sa prise, sinon vous risquez d'endommager irréversiblement la carte mère.

    I have a friends MacBook Pro that has some water damage that caused the MacBook not to be able to use battery power, but still work when plugged into A/C. Upon further inspection I can see visible corrosion on a few of the 9 cables going from the battery connector to that small circuit board. Is it possible to just replace that circuit board?

    jramsey21 - Réponse

    Sometimes it can be enough to just clean the contacts without having to replace the entire board. Dosent work for complicated IC's like plcc type, where corrosion is underneath the chip. Here you will have to reheat and reapply the IC.

    andrehedegaard -

    When placing the battery connector back into the socket on the logic board, check that every part of connector is pressed down. You should hear a soft click when it's back in place.

    Ethan Tarquin - Réponse

    +1

    I thought I made sure it was connected but when running the computer it only detected the battery but couldn’t power it. I had to run with power adapter. Also it didn’t charge. I guess some pins were connected but not all. To verify that all were connected I removed the plastic cover, placed it carefully completely flat, and then reattached the plastic cover. After that it worked!

    Jonas Ehrs -

    Removing the battery connector took a bit of finagling. It wasn’t as easy as one would think. Be very careful when doing this as they warn to not damage it. Otherwise great instructions!!!!

    Peppon - Réponse

    Lift from the long, flat side, not the shorter side. In this picture, you should lift from the NORTH part of the connector, not the WEST side like they are doing. This is because you can spread the pressure from lifting the connector across more area, as compared to the side. I accidentally broke off part of my battery connector lifting it up the way shown, but was able to do it the way I described without problem. Make sure to lift from the wide part so you don’t have my same trouble!

    Jaden Salama - Réponse

    The connector is no more than 1mm thick… the socket is 3-to-4mm deep so make sure you’re trying to remove the connector itself, and not pulling at the socket.

    Richie Egg - Réponse

  6. Pliez le connecteur de la batterie vers le haut afin d'éviter tout contact accidentel avec la prise pendant la réparation.
    • Pliez le connecteur de la batterie vers le haut afin d'éviter tout contact accidentel avec la prise pendant la réparation.

    If you miss or let this step for later like I did, the power left in the battery even though the computer is completely shut down, will screw up the I/O board cable like I did. I noticed this after I put all the pieces back, turn the computer on and surprise, no wifi hardware is detected. -.-

    sebasgaes - Réponse

    I put a small piece of blue painters tape on the battery connector contacts to prevent it from accidentally making a connection and shorting. This helped keep things a bit more protected.

    LaymanLab - Réponse

  7. Dévissez les deux vis Torx T5 de 2,1 mm fixant le support de la nappe de la carte E/S du côté de la carte mère. Retirez le support de la nappe de la carte E/S.
    • Dévissez les deux vis Torx T5 de 2,1 mm fixant le support de la nappe de la carte E/S du côté de la carte mère.

    • Retirez le support de la nappe de la carte E/S.

    Do you know where I can purchase the i/o board cable bracket?

    jodieabc - Réponse

    On my Mac they are p6 screws, not T5?!

    tyler.aman - Réponse

  8. Avec l'extrémité plate d'une spatule (spudger), faites sortir le connecteur de la carte E/S tout droit hors de sa prise sur la carte mère. Veillez à faire seulement levier sur la nappe de la carte E/S et non sur la prise elle-même, vous risqueriez d'endommager la carte mère.
    • Avec l'extrémité plate d'une spatule (spudger), faites sortir le connecteur de la carte E/S tout droit hors de sa prise sur la carte mère.

    • Veillez à faire seulement levier sur la nappe de la carte E/S et non sur la prise elle-même, vous risqueriez d'endommager la carte mère.

    Since I did not remove speakers I skipped this step and went directly to step 17

    Peter Stoll - Réponse

    I don’t understand why the instructions would tell you to remove the speakers if it wasn’t necessary. Can the battery be replaced WITHOUT removing the speakers?

    iwm4 - Réponse

    If you are only replacing an old battery with a new battery, then this step (Step 8) is not required, nor are any of the other steps that involve removing the left and right speakers. It is possible to remove the old battery and install a new battery without removing the speakers.

    Luke Schoen - Réponse

    I couldn’t skip steps 12 & 15 because the speaker assemblies are holding down parts of the battery.

    Dave Olsen - Réponse

    the speaker are better to be unscrewed but not disconnected. You can just turn them away from the battery while replacing and proceed to step 17.

    Igor Kapitanker - Réponse

    I did this as suggested and it was much easier than disconnecting entirely

    N DesRochers -

    This video shows battery replacement without removing speakers.

    https://youtu.be/Lue6lVWhh4o

    jerrylaufer -

  9. Saisissez la nappe de la carte E/S par son extrémité du côté de la carte mère et soulevez-la pour qu'elle ne vous dérange pas au cours des étapes suivantes. Pour éviter d'endommager la nappe, pliez-la seulement au niveau du coude à l'extrémité de la nappe la plus proche de la carte E/S.
    • Saisissez la nappe de la carte E/S par son extrémité du côté de la carte mère et soulevez-la pour qu'elle ne vous dérange pas au cours des étapes suivantes.

    • Pour éviter d'endommager la nappe, pliez-la seulement au niveau du coude à l'extrémité de la nappe la plus proche de la carte E/S.

    If you are only replacing an old battery with a new battery, then this step is not required. See my comments in Step 8.

    Luke Schoen - Réponse

  10. Insérez délicatement l'extrémité pointue de la spatule sous la nappe du haut-parleur droit à proximité du connecteur. Ensuite soulevez-la afin de la déconnecter de sa prise sur la carte mère. Insérez délicatement l'extrémité pointue de la spatule sous la nappe du haut-parleur droit à proximité du connecteur. Ensuite soulevez-la afin de la déconnecter de sa prise sur la carte mère.
    • Insérez délicatement l'extrémité pointue de la spatule sous la nappe du haut-parleur droit à proximité du connecteur. Ensuite soulevez-la afin de la déconnecter de sa prise sur la carte mère.

    I have performed battery swap without disconnecting the speakers!

    Aleš Smokvina - Réponse

    Did that mean that you left the speakers attached to the case? If so, did that make removing the end sections of the battery very difficult? Thanks.

    iwm4 - Réponse

    If you are only replacing an old battery with a new battery, then this step is not required. See my comments in Step 8.

    Luke Schoen - Réponse

    On mine the cable connector pulls out to the left, not upwards

    John Harland - Réponse

  11. Soulevez délicatement la nappe du haut-parleur droit pour la dégager du boîtier supérieur. Soulevez délicatement la nappe du haut-parleur droit pour la dégager du boîtier supérieur. Soulevez délicatement la nappe du haut-parleur droit pour la dégager du boîtier supérieur.
    • Soulevez délicatement la nappe du haut-parleur droit pour la dégager du boîtier supérieur.

    I have successfully replaced battery without removing the speaker cables, as proposed by the comments in the next steps.

    Furthermore, in the steps after 22, where the battery is removed from the upper case, I have easily performed with a credit card and a drop of rubbing alcohol on it and finished in several minutes. Try it!

    kem - Réponse

    Kem, please could you explain how you got the end battery sections out of the case with the speakers still attached. Still very puzzled by this!

    iwm4 - Réponse

  12. Enlevez les vis suivantes, fixant le haut-parleur droit au boîtier supérieur :
    • Enlevez les vis suivantes, fixant le haut-parleur droit au boîtier supérieur :

    • Une vis Torx T5 de 5,7 mm

    • Une vis Torx T5 de 6,5 mm

    • Une vis Torx T5 de 3,8 mm

    Make sure you replace these screws exactly where they came from, same with the other speak.

    Dustin Steward - Réponse

  13. Soulevez le haut-parleur droit à l'endroit où se situe la nappe et enlevez-le du boîtier. Soulevez le haut-parleur droit à l'endroit où se situe la nappe et enlevez-le du boîtier. Soulevez le haut-parleur droit à l'endroit où se situe la nappe et enlevez-le du boîtier.
    • Soulevez le haut-parleur droit à l'endroit où se situe la nappe et enlevez-le du boîtier.

    When replacing with the new speaker, the new piece could have some blue strips on the cable. Remove them to let the adhesive do its job and attach the cable to the surroundings to avoid having it loose.

    Victor Alcantar - Réponse

    I was wondering where I can buy a good replacement. Some users comply about the bad quality of sound after replacing the speakers. Can you suggest a link where to buy good replacement parts (possibly Italy / EU ) ?!

    Alberto Mennella - Réponse

Conclusion

Pour remonter votre appareil, suivez ces instructions en sens inverse.

48 autres ont terminé cette réparation.

Merci à ces traducteurs :

en fr

100%

Ces traducteurs nous aident réparer le monde ! Vous voulez contribuer ?
Commencez à traduire ›

Andrew Optimus Goldheart

Membre depuis le 17/10/2009

475 228 Réputation

410 tutoriels rédigés

Équipe

iFixit Membre de l'équipe iFixit

Community

136 membres

16 675 tutoriels rédigés

2 commentaires

my Speaker tone … can i stitch it ?

Mr Jay - Réponse

Il ne faut surement pas plier la nappe de la carte E/S mais dévisser son support afin de ne pas l’endommager. Une fois pliée, elle ne reviendra jamais parfaitement droite. Il y a deux petites vis qui maintiennent le support qu’il faut dévisser, à moins qu’il y ait encore quelque chose de caché !

Yves Cirotteau - Réponse

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 14

7 derniers jours : 175

30 derniers jours : 940

Total : 43,892