Réparez vos affaires Communauté Boutique

Ce tutoriel a des changements plus récents. Passer à la dernière version non vérifiée.

Shure SM58 XLR Connector Replacement

Introduction

The XLR connector is the place where the XLR cable connects to the microphone. If the connector is pulled out, the internal wiring of the microphone can be damaged.

Ce dont vous avez besoin

  1. Shure SM58 XLR Connector Replacement, Connector: étape 1, image 1 de 3 Shure SM58 XLR Connector Replacement, Connector: étape 1, image 2 de 3 Shure SM58 XLR Connector Replacement, Connector: étape 1, image 3 de 3

    • While holding the microphone connector in one hand, and the XLR cable in the other hand, slowly pull them apart.

    • Make sure you are not holding the microphone connector by the wires.

    • Check to make sure all of the internal wires are connected. If you see a disconnected wire, take a look at the connector soldering guide.

    Traduire

  2. Shure SM58 XLR Connector Replacement: étape 2, image 1 de 2 Shure SM58 XLR Connector Replacement: étape 2, image 2 de 2

    • Hold the microphone connector in one hand and the microphone base in the other.

    • Line up the screw in the connector with the hole in the middle of the microphone.

    • Also, align the ridge on the microphone connector (located near the top of the connector) with the slot in the base of the microphone.

    Traduire

  4. Shure SM58 XLR Connector Replacement: étape 3, image 1 de 2 Shure SM58 XLR Connector Replacement: étape 3, image 2 de 2

    • With those parts aligned, push the connector back into the microphone until the screw lines up with hole in the side of the microphone.

    • Do not push the microphone past this point or the connector may become stuck.

    Traduire

  5. Shure SM58 XLR Connector Replacement: étape 4, image 1 de 1

    • Using a small flat head screw driver, turn the screw in the side of the microphone clockwise until it is tight.

    Traduire

    Hi looks simple but I can't undo screw turns so far and locks up. Can you help. Kind regards.

    Tony White - Réponse

    Are you trying to disassemble or reassemble the microphone?

    Daniel Berger - Réponse

    In my case, i try to disassemble.. But it wont come off. Anticlockwise the screw… infinite turns… TheThe connector is not stuck, it wabbe a bit, but the screw maybe wont recess enough.

    nunoandrade - Réponse

    How do I replace the screw? Lost it, and need to replace it.

    Katrina - Réponse

Conclusion

Following these steps should reinstall the XLR connector back into the microphone.

2 autres ont terminé cette réparation.

Auteur

avec 6 autres contributeurs

nat coll

Membre depuis le 09/27/12

642 Réputation

14 tutoriels rédigés

Badges: 12

+ 9 badges supplémentaires

Équipe

Cal Poly, Team 7-53, Forte Fall 2012 Membre de l'équipe Cal Poly, Team 7-53, Forte Fall 2012

CPSU-FORTE-F12S7G53

5 membres

20 tutoriels rédigés

2 commentaires

simple clear and precise. Small problem fixed in no time, thank you very much!

Kimmo Pekari - Réponse

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 3

7 derniers jours : 13

30 derniers jours : 86

Total : 17,348