daniel

@tech_ni

daniel

9 127	Réputation
666	Solutions
0	Tutoriels
Membre depuis 06/08/2017

Votes

Questions

Stuck at apple logo 19/12/2019
After lcd fpc replacement phone booted fine. Now stuck on apple logo and power supply showing 0.33 amps when button is...
Red light a beep 07/05/2019
Has anyone found a fix for ghd platinum red light and beep yet
Need schematics urgently please 03/04/2019
This laptop won't turn on after a power cut. When the charger is plugged in the power brick light goes out. I felt a...
not charging and taking along time to boot to home screen 18/01/2019
@refectio i have an issue with this iphone 6. when i got it, it wouldnt boot. on dc and charger with battery disconnected...
no power even after both power ics changed 24/08/2018
so i have an s6 edge+ no power, replaced both power ic’s. getting around 3.5v in both locations but not turning on and no...
vdd main short but no heat 14/07/2018
so i have an iphone 7 in this morning and as title says i have a vdd main short, wire soldered on and drawing 2 amps but...
dim backlight after liquid damage 24/05/2018
i have a macbook air 820-3437 which was liquid damaged, doa. corrosion was around smc and u7700, reballed smc and it...
about gsx account not phone 23/05/2018
does anyone have an apple gsx account that can help me figure out how to get an account
will only boot to safe mode 22/04/2018
i have a ps4 that wont boot when the power button is pressed just blue pulsing light, yet it will boot into safe mode and...
iPhone 6 not booting 19/04/2018
im having an issue with an iphone 6, when i got it, it was bootlooping, now i have replaced pmic, tristar and tigris. but...

Page 1 de 4

Continuer

Réponses

Réponse à : « Bricked iPhone 11. What parts should I extract? » 05/07/2021
Everything apart from the logic board and front camera, the lcd will work in another phone but will probably have a verification pop up and you might get that with the battery aswell as they are programmed for the original phone.
Réponse à : « Are display ribbons replacible? » 03/07/2021
You need to replace the screen. Ribbons can only be replaced using bonding machines.
Réponse à : « C-port replacement and PCB mounted pads » 29/06/2021
You have ripped every solder trace from the board. It might be repairable by an experienced technician but will definitely cost more now to repair than it would have done.
Réponse à : « Why is my screen black? » 26/06/2021
Shine a light on the screen, if you see the picture it could be a backlight issue or could be the screen has went bad.
Réponse à : « Phone in not charging, does this connector look normal? » 23/06/2021
Change the port, looks bad
Réponse à : « Logic board black insulation tape damage » 17/05/2021
The sticker isn’t the issue and I doubt the port is either if neither work. Could be the hydra chip has failed and needs replaced.
Réponse à : « Replacement switch fan amps » 05/05/2021
No it will be fine there’s not a lot of difference.
Réponse à : « I accidentally removed the sticker in front of the lcd, is it valid fo » 05/05/2021
If it was stuck to the screen protector I doubt it will void warranty as it’s not a location a warranty sticker should be.
Réponse à : « iPhone 6s motherboard swap question » 01/05/2021
Board and home button from the old phone and Touch ID will work. If you use a different home button you will lose Touch ID.
Réponse à : « Schematics for the tristar area - Anyone can help? » 26/04/2021
here’s a boardview of the components that pad is connected too.

Page 1 de 67

Continuer

Réputation au fil du temps

Répartition de la réputation

Évènement	Compte	Delta
La contribution a reçu un vote positif	492	5876
Réponse acceptée	122	3660
Réponse acceptée	4	40
A voté négatif pour une contribution	1	-2
La contribution a reçu un vote négatif	8	-48
Votre commentaire a été supprimé en raison de signalements	4	-400