Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.
Ce dont vous avez besoin
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Unplug the monitor for 24-48 hours. Wait 5-7 days before swapping the filter capacitor.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the 4 screws from the monitor stand with a Philips #1 screwdriver. Remove the bottom screws first.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Sort this screw separately, as it is unique.
-
Remove 4 fine threaded screws from the back of the monitor with a Phillips #0 screwdriver. All of these screws are the same.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
On the bottom of the monitor, there are four slots to open the monitor. To release these clips, use a Jimmy or flathead screwdriver.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
With the monitor unclipped on the bottom, pull the sides of the monitor up. Do this slowly to avoid cracking the LCD.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
With the back of the monitor off, remove the 2 screws on the IEC power connector using a Phillips #0 screwdriver.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the 4 screw pins for the video cables from the monitor. Use a 5mm Nut bit/driver to remove the screw pins from the power supply shield.
-
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Disconnect the CCFL cables from the power supply board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Disconnect the flat flex cable that goes to the control board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the 2 lower screws that hold the power supply shield to the monitor with a Phillips #0 screwdriver.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
On the right side of the monitor, remove the remaining screws holding the shield in place.
-
Lift the lower plate up while removing the power supply shield to remove it from the monitor. Once this is done, you will have access to the power supply.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
This capacitor is only found on older power supplies. Replacement is advised, but not required.
-
With the power supply shield removed from the monitor, identify the power supply. Take note of the values, including the inverter cap (if present).
-
Remove the 4 screws from the power supply. Once this is done, lift up the power supply at a slight angle to clear the chassis. Do not lift too much or the connector may be damaged!
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
If you are unsure of the position of the capacitors, mark the polarity with a permanent marker. If the capacitors are incorrectly installed, they will explode when power is applied.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
To prepare the board for capacitor replacement, add flux or solder.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Move to a workspace with ventilation or use a fume extractor. Once in an appropriate workspace, desolder the old capacitors. Heat up each leg and remove it.
-
After removing the capacitors, clean up the old solder with a desoldering braid. Lift it with the iron when removing it.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Install the new capacitors. Check the polarity and bend the leads so they do not come loose during installation.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Once the polarity is verified, solder the capacitors in. After installation, cut off any excess lead.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
After verifying there are no cold solder joints, clean the board. This can be cleaned with 91%+ Isopropyl or denatured alcohol.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Put the monitor back together and test the repair.
-
Annulation : je n'ai pas terminé ce tutoriel.
12 autres ont terminé cette réparation.
28 commentaires
I did not replace the large capacitor on the Acer monitor yet. All other caps have been replaced. I may have to replace the FSPO55- ZP102A as it has a hot spot beside it. I don't know if the part number is right? Do know where I can buy it. Tom B
These older CCFL panels usually burn on the PCB by the inverter coil and main transformer (the Delta branded part, in this case). The LED monitors limit the failure points to the transformer.
It sounds like your PCB got burned from the heat by the transformer or the inverter coil. This is very common and the boards are designed to take it. However, if you are concerned you should buy a new power supply board altogether if that makes you more comfortable.
Nick -
In step 12, replacing the capacitors with ones with a different capacitance rating instead of using a capacitor rated for higher voltage makes no sense to me electrically. The capacitance rating is the important part, if you use a capacator rated for say 35 volts when the original is rated for 10 makes no difference whatsoever. the rating just means MAX voltage.