Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.
Ce dont vous avez besoin
-
-
Si la vitre de votre écran est fissurée, évitez qu'elle se brise davantage et empêchez toute blessure pendant la réparation en la recouvrant de bande adhésive. Cela permet également d'obtenir une surface lisse permettant à la ventouse de mieux tenir.
-
Posez la ventouse aussi près du bord avec le bouton de volume du téléphone que possible, tout en évitant le bord incurvé.
-
-
-
-
Posez un iOpener chauffé près du capteur de proximité sur le bord supérieur du châssis central pendant deux minutes, afin de ramollir son adhésif.
-
-
Outil utilisé dans cette étape :Magnetic Project Mat$19.95
-
Décollez le morceau de bande adhésive qui couvre la vis en-dessous du haut-parleur interne. Décollez aussi toute bande adhésive qui recouvre d'autres vis.
-
Retirez les vis suivantes qui fixent le châssis central :
-
Onze vis cruciformes de 3,7 mm
-
Une vis Torx T5 de 4 mm
-
-
-
Soulevez le châssis central en commençant par le bord inférieur.
-
Lorsque le châssis central est à un angle d'environ 45° par rapport au reste du téléphone, soulevez-le tout droit vers le haut hors du téléphone.
-
Quand vous soulevez le châssis central, faites passer le capteur de proximité soigneusement à travers la petite fente dans le châssis central.
-
-
-
Utilisez l'extrémité plate d'une spatule pour déconnecter le connecteur de la batterie.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use the flat end of a spudger to disconnect the charging assembly connector.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use the point of a spudger to pry the white antenna cable connector straight up and disconnect it from the charging assembly board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use tweezers to pull the white antenna cable straight up and out of the metal clips on the board and out of the channel on the loudspeaker.
-
Move the cable to the left of the phone to keep it out of the way of the loudspeaker.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use the tip of a spudger pry the black antenna cable connector straight up and disconnect it.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use tweezers to lift the black antenna cable out of its channel on the loudspeaker.
-
Move the cable toward the top of the phone to keep it out of the way of the loudspeaker.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use the tip of a spudger to gently push the speaker cable connector out of its socket horizontally, alternating pushing either side of the connector out a little bit at a time.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use an opening tool to pry the loudspeaker assembly up slightly from its recess in the phone.
-
Hold the silver charging assembly cable out of the way while you're working, but be careful not to bend it too far or apply too much strain where it connects to the charging assembly.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Rotate the top right corner of the loudspeaker toward the top of the phone while sliding the whole assembly to the right.
-
Remove the loudspeaker.
-
Annulation : je n'ai pas terminé ce tutoriel.
7 autres ont terminé cette réparation.