Aller au contenu principal

Réparez vos affaires

Droit à la réparation

Pièces & Outils

Introduction

Consultez ce tutoriel pour remplacer la batterie de votre Nexus 7.

  1. Éteignez votre appareil. Insérez un outil d'ouverture en plastique dans la jointure sur la tranche de la tablette et parcourez-la en faisant levier de chaque côté, l'un après l'autre.
    • Éteignez votre appareil.

    • Insérez un outil d'ouverture en plastique dans la jointure sur la tranche de la tablette et parcourez-la en faisant levier de chaque côté, l'un après l'autre.

    • Ne faites pas levier à côté du port USB, en bas de l'appareil. Vous risqueriez de fissurer la coque arrière.

    I had a heck of a time doing this, spent ten or twenty minutes carefully prying, and I STILL cracked the case. At least on mine, the case was held in VERY well and required prying pretty much everywhere before it would let go. The tools I bought from iFixit really helped, but still a royal pain to open.

    pacmanmaster - Réponse

    a couple of obscure things that might help in opening:

    guitar pick. get a few; they are cheap.

    a prying device made for the sign industry: its called"lil' chizler". I have found that this to be the most helpful opening tool.

    http://www.ebay.com/itm/like/16184595677...

    also

    https://www.qualitylogoproducts.com/trad...

    you can use the broken screen unit to test.

    Len Gorsky - Réponse

    Add "remove the sim tray"...

    Iain Lennon - Réponse

    I echo the previous - a right royal pain to get the cover off! I started on the right side as seemed to be more give there… iFixit tools helped tho!

    Steven Emery - Réponse

    Just for the sake of clarity, I would add that you need to pry between the plastic bezel and the back casing. Not between the glass and bezel. Someone had already tried on the one I worked on and part of the bezel was missing in the top right corner. Made my job easier!

    The best tools for this part are definitely something like the iFixit Jimmy and their opening tool, a few guitar picks and a spudger. Not too difficult once you get the first separation.

    Cool_Breeze - Réponse

    I managed to easily crack the screen, guess I’ll have to order a new one and “try” to put it in, in addition to the original job of replacing a dead battery on Nexus 7 2013..ahhhhhh, slow learner…

    Gary Stamey - Réponse

    Opened the case for the first time. It took me a while to find any gaps, but I found that the easy way to begin was using your fingernail to get into the sides. The middle left and middle right seemed a lot easier to…slip a nail in compared to the rest of the case, especially the corners and the top and bottom. With a small opening on both sides I used the opening tool to increase the gaps while using a couple of guitar picks to prop up the device against the back case. With most of the sides exposed, I worked on the bottom (create opening, leave a guitar pick to keep that part open, use the opening tool to get the rest out), and the opening was pretty much complete.

    So far only the corners of the back case showed small cracks and my screen was pretty much unscathed.

    Nam Lam - Réponse

  2. Servez-vous de votre outil d'ouverture en plastique et de vos doigts pour détacher complètement la coque arrière de la tablette au niveau de la jointure.
    • Servez-vous de votre outil d'ouverture en plastique et de vos doigts pour détacher complètement la coque arrière de la tablette au niveau de la jointure.

    • Faites attention dans les coins. L'appareil est fragile.

  3. Insérez votre outil d'ouverture en plastique sous le côté du connecteur de la batterie et faites délicatement levier pour le débrancher.
    • Insérez votre outil d'ouverture en plastique sous le côté du connecteur de la batterie et faites délicatement levier pour le débrancher.

    THIS should be the first cable to disconnect. Always remove power first!

    dave - Réponse

    We moved this step to be fist, thanks for the edit!

    Sam Goldheart -

  4. Fix Kits pour écrans LCD d'iPhone

    L'option économique couverte par notre garantie à vie.

    Acheter des kits

    Fix Kits pour écrans LCD d'iPhone

    Réduisez les coûts de réparation et non pas la qualité.

    Acheter des kits
  5. Prenez l'extrémité plate d'une spatule ou votre ongle pour retourner le clapet de protection transparent de la prise ZIF de la nappe. Toujours avec l'extrémité plate d'une spatule ou votre ongle, soulevez la partie étroite du connecteur (du côté opposé de la nappe) pour détacher la nappe de sa prise. NE FAITES PAS LEVIER sur la prise du côté de la nappe, vous risqueriez d'arracher toute la prise de la carte mère.
    • Prenez l'extrémité plate d'une spatule ou votre ongle pour retourner le clapet de protection transparent de la prise ZIF de la nappe.

    • Toujours avec l'extrémité plate d'une spatule ou votre ongle, soulevez la partie étroite du connecteur (du côté opposé de la nappe) pour détacher la nappe de sa prise.

    • NE FAITES PAS LEVIER sur la prise du côté de la nappe, vous risqueriez d'arracher toute la prise de la carte mère.

    • Faites glisser la nappe hors de la prise ZIF.

    • Pour plus d'infos sur la façon de débrancher les connecteurs ZIF, consultez le tutoriel "Reconnaître et débrancher les connecteurs".

    Flip up on the WHITE part, facing away from the cable. I sort of struggled with this part, but fortunately didn't do any serious damage.

    yuguoxiong - Réponse

    This is the correct way to do it. Flipping up the white part is what you have to do. I tried flipping up the black part and some of it broke off.

    Ryan -

    I found that I had to flip up on the black part here. I broke a section of the white trying to flip it up.

    pattylanter - Réponse

    This comment saved me on this step. Indeed the secret is to flip up the black part of the connector, located opposite the side where the cable inserts.

    Hannah Cirimele -

    This is wrong, these comments should be deleted so as to not confuse more people.

    Jeff Andrews -

    It's possible there's more than one color variation in production on these Nexus 7 ZIF sockets. To complicate matters, it looks like the guide's original author/photographer may have simply yanked the ribbon cable out without opening the socket, so there's very little visual clue here as to which is the right section to flip up. Based on these photos, I'd say Hannah's tip is probably correct—you want to flip up the thinner portion of the socket, opposite the cable (regardless of its color scheme). If someone who has successfully completed this step could supply a better photo, that would be super helpful!

    Jeff Suovanen -

    I revised the text so there's no long any mention of the coloration of the socket.

    Jeff Suovanen -

    I believe I broke the ZIF attached to the mobo at this step; is there any other way to reconnect it during reassembly or will I require a new mobo?

    Neil Reed - Réponse

    This was my first time with this kind of ZIF socket and found these instructions/pictures ambiguous. In hindsight I see what was being described (actually used the replacement daughterboard as my guide). May I suggest this phrasing:

    The ZIF clamp hinges on the side opposite of where the cable in inserted. Using the flat end of a spudger or your fingernail, flip the thin portion of the connector up and away from the insertion side of the connector.

    charles fineman - Réponse

    Correction of Charles' Oct comment: The ZIF clamp hinges on the same side as the cable is inserted, the side towards the battery. The cable runs over the battery and into the thick connector, with contacts both on the side closest to the battery and on the side away from the battery. Beyond the contacts on the side away from the battery is the thin part to be lifted. Using the flat end of a spudger or your fingernail, flip the thin portion of the connector up and towards the insertion side of the connector. You can leverage gently against the big copper-covered area on the side away from the battery, in lifting the thin (white in the current picture) part of the connector.

    tballou - Réponse

    You can leverage gently against the big copper-covered area on the side away from the battery, in lifting the thin (white in the current picture) part of the connector, using a motion similar to the described in step 5 below for removing the orange ribbon connector.

    tballou - Réponse

    some better macro photos of the zif socket would help a lot, in closed and open states

    Iain Lennon - Réponse

    For anyone like me who has only experience with metal connectors similar to iPhones, this is a "switch-on/switch-off" connector.

    The cable doesn't pop out by itself, you have to pull it out yourself.

    Light to moderate pressure required.

    Jason - Réponse

    Please make the pictures clearer as Iain Lennon said. I too was a fool to not read the comments and broke the connector off of the motherboard.

    Yumi Blesh - Réponse

    Ha.

    So one side of the cable has a white strip connector, and the other side has a black strip connector. (both comments above are correct, depending on which side you are looking at)

    The side in the photo has a black connector strip that needs to be opened. It is the long small strip of plastic on the _opposite_ side of the connection point, to the cable.

    It clicks up into the air, like on a hinge.

    The cable then pulls out, without any resistance.

    Warwick - Réponse

    Having totally destroyed the ZIF connector I can now say that the WHITE portion is hinged and the BLACK portion is not. Both parts are extremely fragile. The photographs are really useless.

    David Spitzer - Réponse

    exactly ……..

    esykas -

    This shouldn’t be the first cable to disconnect. Disconnect the battery cable first. Always remove power first!

    dave - Réponse

    Good catch @hobohax0r, we rearranged the steps to help fix that!

    Sam Goldheart -

  6. Décollez l'adhésif de protection qui recouvre le connecteur de la nappe orange en haut de la carte mère.
    • Décollez l'adhésif de protection qui recouvre le connecteur de la nappe orange en haut de la carte mère.

    • Vous devriez voir à présent tout le connecteur de la nappe et ses languettes en plastique.

  7. À l'aide d'une pincette, décollez l'adhésif de protection argenté en haut du connecteur de la nappe orange. Servez-vous d'un outil d'ouverture en plastique pour faire levier sur le connecteur de la nappe orange. Il devrait sortir facilement. Servez-vous d'un outil d'ouverture en plastique pour faire levier sur le connecteur de la nappe orange. Il devrait sortir facilement.
    • À l'aide d'une pincette, décollez l'adhésif de protection argenté en haut du connecteur de la nappe orange.

    • Servez-vous d'un outil d'ouverture en plastique pour faire levier sur le connecteur de la nappe orange. Il devrait sortir facilement.

  8. Maintenant que les deux nappes principales sont débranchées, repliez-les et maintenez-les de côté avec votre main ou bien une pincette ou un objet léger pour qu'elles ne vous dérangent pas au cours des prochaines étapes. Maintenant que les deux nappes principales sont débranchées, repliez-les et maintenez-les de côté avec votre main ou bien une pincette ou un objet léger pour qu'elles ne vous dérangent pas au cours des prochaines étapes.
    • Maintenant que les deux nappes principales sont débranchées, repliez-les et maintenez-les de côté avec votre main ou bien une pincette ou un objet léger pour qu'elles ne vous dérangent pas au cours des prochaines étapes.

    How called is the left one ? I broke it and i will buy it but cant find it..

    Timo Dohmen - Réponse

  9. Servez-vous d'un tournevis cruciforme #0 pour dévisser les quatre vis cruciformes #0 argentées de 3 mm qui entourent la batterie.
    • Servez-vous d'un tournevis cruciforme #0 pour dévisser les quatre vis cruciformes #0 argentées de 3 mm qui entourent la batterie.

    There are 6 screws on mine. One at the top and the other directly across from that on the other side of the battery at the bottom. These two screws are covered with a small adhesive sticker that says “seal". Those stickers need to be removed so the Phillips screwdriver can be inserted to remove them.

    dabair30 - Réponse

    Correcrion, there are 7. One more at the top left corner of the battery tray. The last 3 screws are slightly larger than the first 4.

    dabair30 - Réponse

    I found using a #00 Philips worked better for my removal.

    Todd - Réponse

  10. Appuyez en bas de la batterie puis soulevez-la pour l'ôter de votre appareil.
    • Appuyez en bas de la batterie puis soulevez-la pour l'ôter de votre appareil.

    If your replacement battery doesn’t have the metal battery tray included (like mine came) be aware you’ll have to CAREFULLY pry the old battery out of the metal tray. It has some pretty strong glue holding it in, but prying on it slowly and carefully should get it free without bending up the metal tray. There should be enough glue residue left in the tray to hold the new battery in, at least until you get the tablet back together.

    Tracy Nash - Réponse

    Thank you for the very helpful comment - I was facing the same issue!

    Jorge Gomes -

    You probably should add that the battery is held in the tray with some glue strips. It took a bit to carefully remove the battery from the tray without bending the tray too much. Also, the replacement battery I had was slightly smaller than the OEM battery. When putting back together make sure you place the battery in the tray so the battery is close enough to the battery connector and you can reconnect the battery without pulling on the connector wires.

    Todd - Réponse

    Having replaced the battery I find it doesn't charge. Which connector could be at fault please?

    mxclubman - Réponse

Conclusion

Pour remonter votre appareil, suivez ces instructions en sens inverse.

62 autre(s) ont terminé cette réparation.

Merci à ces traducteurs :

100%

Claire Rapp nous aide à réparer le monde ! Vous voulez contribuer ?
Commencez à traduire ›

Heather

Membre depuis le 22/01/2015

1 317 Réputation

2 tutoriels rédigés

Équipe

Cal Poly, Team 20-16, Maness Winter 2015 Membre de l'équipe Cal Poly, Team 20-16, Maness Winter 2015

CPSU-MANESS-W15S20G16

4 membres

24 tutoriels rédigés

18 commentaires

Don't be a goof like me and spend seven minutes trying to pry in the gap between the screen glass and the plastic. I thought that the plastic cover wrapped around the whole of the side and met the unit just under the glass. Nope...find the seam near the halfway point of the case side, between plastic and plastic. (The first photo here is not sufficiently clear to make this obvious.)

ceristaggbusiness - Réponse

This is such a valuable comment. The photos are VERY misleading. Thank you for pointing this out!

q3cq3c - Réponse

1 If you look closely, you'll see that at the edge of the glossy, black screen there is a glossy, black, 1mm hard plastic band going all the way around the screen. This provides the beveling on the edge of the screen. Around that is the dull, black plastic case. Insert your spunger or fingernail between these two plastic bands. It is easiest to do near the middle both of the long sides. Gently slide up toward the corners popping each little snap. When you get near the corner, keep one fingernail/spunger in the gap you've created on the side, near the corner, then use another nail/spunger to go around the corner. Be careful here. This is the easiest place to damage.

Once the corners have popped, the end/short top edge is easy. The bottom edge is different since the micro-USB port is also there. I did not pry it open but lifted the other three sides and just slid the screen out from that end. I inserted the USB end first also when reassembling, snapping the other edges then corners in afterward.

Greg Conquest - Réponse

2 I did crack that hard plastic band in two spots on the top left corner of my Nexus 7 (opposite the camera). On spot a tiny piece broke out, but the band is still continuous at the glass edge. Around the corner, the band actually appears to have broken in two. If I rub my finger there, I can begin to peel it up. I hope my case will keep it protected.

Greg Conquest - Réponse

I had trouble with the stupid ribbon cable zif socket. Everything went well until the very end when I was reassembling and I had to stick that sucker in. It was really difficult, and the plastic tab came off. Then the end I pulled out at the beginning wasn't going back in. After trying to glue the plastic pulling-flap back on (hint: don't do that) I gave up, but then I had an idea. I pulled out the entire ribbon from both ends and just flipped them. Put in the troubled end in the bottom socket (it was easier than wrestling with it), and the better end in near the top of the tablet next to that orange ribbon, and it worked! I'm so relieved...! Now my tablet is back to working condition!

Hanna - Réponse

Step 1: if you have the LTE version, REMOVE THE SIM CARD TRAY. It's silly brittle as-is.

Step 2: It's the seam between plastic and plastic, NOT next to the glass! After so many comments, I don't know how this hasn't been mentioned in the tutorial.

alex - Réponse

WTF. I cannot begin to pry off the cover, the way the picture shows -- even with my official Fixit pry tools, which are now pretty much shot. But I did manage to break a few pieces off of the slim plastic protecting the edge of the screen. BTW, I did pry between the two plastic sections, not next to the glass.

Be warned that these instructions do not accurately show how hard this is and how dangerous to the cosmetics of your tablet. Glad I didn't order the battery yet, because my Nexus is likely done for. Thanks guys.

Upwith Privacy - Réponse

UPDATE: I finally got the cover off by carefully using a small knife. The cover edges are scarred and a small clip broke off at the first corner. It was brutal and the FIXIT plastic tools were worse than useless.

Upwith Privacy - Réponse

I just did this, and appreciate the comments above. I couldn't get the old battery out because it is glued in. There is another tutorial on YouTube that suggests first taking the battery tray out (four screws) which made it much easier to pry the battery out.

Bob Gates - Réponse

I had to disconnect the battery to get my device out of a crash at the first "Google" screen. This guide was what I needed to get in. Do add "remove the sim tray" at the start though...

I'd suggest getting someone to take macro photos of the zif socket in closed and opened states though. It is not clear how to open it up from the text, despite a description to try and help. And, as it needs a little force in the right place (and because the socket opens counterintuitively) I think it could help other people to do this bit safely. I would have if I wasn't swearing at the socket at the time, and didn't think to do so...

Iain Lennon - Réponse

Instructions could be better overall. Better pictures needed as well. Also the battery is taped into the tray and difficult to remove. This is not noted here.

Nick Barber - Réponse

You can buy the replacement with or without the tray. Mine came without so I had to detach the old one from the tray - it's suprisingly flexible, so I worked my way slowly whilst mentaly preparing for a sudden fire :/ Anyway it's worth noting here. Also +1 to the tray remark. I figured that one out, but only before forcing it a bit. Good luck :)

Konrad Skrzypek -

Here are my comments in the hopes they will help someone else. Although I DID finish it, and it is showing that it IS charging...it remains to be seen yet whether my tablet works. :-(

Well....I did it! The three issues I had were: 1) The d**n battery was GLUED to the casing! so I ended up bending the very SOFT metal to get it out; I figured I could force it flat again once screwed in 2) Replacing the "ribbon cable ZIF socket" afterwards was almost impossible but I figured it was due to the metal battery case being bent and not flat; I struggled to get this one in and out several times; Same with re-attaching the orange ribbon connector was dicey because it also was not fitting tight onto the match; I had to stretch it and push real hard then try to retape . 3) Don't-REPEAT: DON'T even TRY this without the exact size tiny Phillips screwdriver...that was a big part of my frustration.

I hope these comments help someone else, because I was extremely grateful for this site!

sharon - Réponse

The battery was very hard to get out of the tray. I gently warmed it with a dryer on low and a little plastic pry tool slowly releasing it. I inserted the pry tool under the side with the plug for the battery and worked my way down. Once that side was free it was easier to release the other, though I bent the tray slightly. It is held by 2 pieces of double stick tape on either side of the battery. All-in-all it was a tedious task. I would say not for a beginner.

cindy Okinczyc - Réponse

Just finished, and it powered on at least. I’ve had an intermittent issue where the battery just drops out completely and shuts down. Figured a loose connection or bad battery and decided to try and replace, as it is going on 5 years old.

Removing the cover was tricky, luckily the left side plastic bezel had a small chip in it that made it easy to start. Cracked the bezel in the bottom left corner, and accidently cracked between the edge and volume down.

Had a stuck screw, moved to a PH000 and wiggled it back and forth until it got a grip and came loose. I saw blue stripes, so glue or thread locker is likely on them.

Worst part was getting the battery off the tray, which is held down by two strips of double side tape on the left and right edges. Eventually got it off, and good thing I had the new battery because I didn’t do the best job of getting the old one out.

Hopefully this fixes the issue.

Chance Waterman - Réponse

Last step: Pry the old battery out the the enclosing aluminum frame. Use some gentle heat on the back if it’s stuck. Insert the new battery into the frame using the same orientation and reinstall it into the tablet using the four philips screws.

Nick Vee - Réponse

Definitely not 10 minutes, getting the back off was insane. Poked and pried for an hour or so before I finally got it to come free in one spot, then worked a guitar pick tool around from there to finally get it completely open. Once open, it was pretty easy to get the battery tray out, but the only replacement battery I could find didn’t come with a tray, so I spent another large chunk of time wedging the flat end of a spudger between the tape and the old battery and rotating it back and forth to peel a bit of battery off the tape at a time (the old battery had inflated pretty good, and fortunately I didn’t pop it). Went back together trivially, seems to work, and is charging now. The screen is flat again, not bulged in the middle.

Thomas Horsley - Réponse

Done. No damage to the screen itself, couple of scratches of the bezel (ill attempt at opening the top with a stanley), small cracks at a few corners of the back case. Most troublesome part was the first step, but I finally got an opening after slipping a nail in the middle of the sides (either side is easy). Repair was straightforward from then on.

Thanks ifixit. Your tools and your guide really helped this beginner. Now I don’t have to drop 500 on a tablet.

Nam Lam - Réponse

Ajouter un commentaire

Afficher les statistiques:

Dernières 24 heures : 13

7 derniers jours : 87

30 derniers jours : 335

Total : 31,827