Aller au contenu principal

Réparez vos affaires

Droit à la réparation

Pièces & Outils

Introduction

La caméra frontale de votre iPhone n'arrive plus à prendre de photos ? Il est peut-être temps de la remplacer. Utilisez ce tutoriel pour remplacer l'ensemble capteur et caméra avant, y compris le capteur de luminosité ambiante et le microphone, dans un iPhone 7.

Vidéo d'introduction

  1. Avant de commencer, déchargez la batterie de votre iPhone au dessous de 25%. Une batterie au lithium peut prendre feu et/ou exploser si elle est accidentellement percée.
    • Avant de commencer, déchargez la batterie de votre iPhone au dessous de 25%. Une batterie au lithium peut prendre feu et/ou exploser si elle est accidentellement percée.

    • Éteignez votre iPhone avant de commencer le démontage.

    • Retirez les deux vis Pentalobe de 3,4 mm qui se situent sur le bord inférieur de l'iPhone.

    • Ouvrir l'iPhone fera perdre son étanchéité à l'appareil. Préparez des nouveaux joints d'étanchéité avant de passer à l'étape suivante ou veillez à ne pas exposer votre iPhone à des liquides si vous ne remplacez pas les joints.

    Can anyone confirm 7/7P's pentalobe screws have a ring of seal near the screw head?

    Cooper Chase - Réponse

    Confirmed, the screws have a black ring seal around the head.

    rcheing - Réponse

    Can’t get the display front

    Bernadette Pfeifer - Réponse

    From personal experience, I highly recommend before doing this procedure or any other, that you do a backup of your phone (preferably local) in case your procedure goes south.

    ballina5ny - Réponse

    I purchased the repair tools with the replacement battery from iFixit. The tools include a screw driver and three heads none were labeled 3.4 mm. I think the one that fit the pentalobe screws was labeled Y000. The guide should identify the screw driver head supplied by the kit not 3.4mm.

    Mark Lieberman - Réponse

    in the iphone 7 replacement battery kit from iFixit, the screwdriver that fits the 3.4 mm pentalobe screws is labeled P2 (and not Y000)

    Jan-Tijn Oppermann -

    the screwdriver PH000 does not work i wasted two screws and now they dont have the 4 cross mark they are now a circle, i buyed it all from Paraguay and it doesnt work, had to assembly back the parts because i got stuck like i mention with some screws, well im just going to send to a professional to install, thanks

    Martin Frutos, Nuñez - Réponse

  2. Faire chauffer la partie inférieure de l'iPhone aide à ramollir la colle qui maintient l'écran et rend plus facile d'ouvrir l'appareil.
    • Faire chauffer la partie inférieure de l'iPhone aide à ramollir la colle qui maintient l'écran et rend plus facile d'ouvrir l'appareil.

    • Utilisez un sèche-cheveux, ou bien préparez un iOpener et posez-le sur la partie inférieure de l'iPhone. Patientez environ une minute, ceci fera ramollir l'adhésif en dessous.

    ¿Cuántos segundos son los recomendados?

    joscarlos91 - Réponse

    Sesenta segundos

    Krutav Shah -

    It is a process. I heated the lower area of the phone with a hair dryer on and off (1min each) about 3-4 times before I was able to get the provided tool in.

    Dan - Réponse

    I suggest using a hairdryer. I used the iOpener for maybe 30 mins to no avail. However, when I used the hairdryer the screen came of much quicker.

    Michael - Réponse

    I totally Mr. Myagi’ed it, by rubbing my hands together until they burned, then held the phone un my hot hands. I did this 5-6 times over a couple of minutes. It was a good zen way to get started!

    Ark - Réponse

    Can a heat gun be used?

    Lee - Réponse

    Absolutely. Just don’t overdo it—the adhesive usually softens up pretty easily. If you are experienced with a heat gun, you’ll have no problem. (If you are inexperienced, it’s easy to cook the display or cause other damage.)

    Jeff Suovanen -

    If i use this process, will iphone 7 still be sealed, water/ splash resist after that?

    Marius Serban - Réponse

    Opening the iPhone's display will compromise its waterproof seals. Have replacement seals ready before you proceed past this step, or take care to avoid liquid exposure if you reassemble your iPhone without replacing the seals.

    Angel Hermida -

    Can I use a cpb heating pad to soften the adhesive ? If yes how much time and temperature ?

    davidecongiu - Réponse

    Will doing this compromise the screen protector (Zagg) that I have on my phone?

    Eric Nance - Réponse

    Hairdryer worked for me but I needed to use a razor to pry it open at the bottom then used the spudger

    Gina Torres - Réponse

    Is there a reason why you wouldn’t put the iopener over the entire length of the phone, instead of just the bottom corner?

    BPX - Réponse

    The motherboard is extremely sensitive to heat.

    Neal Reasland -

    Hello can the head damage the id touch bottom?

    After heating opening it stoped working.

    Qrizmasex @ gmail . Com

    aratovski - Réponse

    It definitely can. That happened to me.

    Steve Naylor -

    mine didnt come with a heat pack do i use a hair dryer

    Shy Rose - Réponse

  3. Posez une ventouse sur la partie basse de l'écran, juste au-dessus du bouton home. Assurez-vous de ne pas poser la ventouse sur le bouton home, ceci empêcherait la ventouse d'adhérer à la vitre.
    • Posez une ventouse sur la partie basse de l'écran, juste au-dessus du bouton home.

    • Assurez-vous de ne pas poser la ventouse sur le bouton home, ceci empêcherait la ventouse d'adhérer à la vitre.

    • Si votre écran est méchamment fissuré, le couvrir de ruban adhésif transparent pourra aider la ventouse à adhérer. Sinon, une bande à fort pouvoir adhésif peut être utilisée à la place de la ventouse. Si rien ne fonctionne, vous pouvez coller la ventouse à la superglue sur l'écran cassé.

    The glass is completely cracked and the suction cup doesn't work because it gets air in between. any tip?

    Display is glued and doesn't come off.

    support - Réponse

    A wide, single strip of packing tape, well placed, will solve this for you. :)

    Mimic44444 - Réponse

    Last comment works well. Thank you !

    Using packing tape for a cracked screen should be included in the description in Step 3.

    Cracked screen is most probably the reason you are replacing it.

    Arni Benediktsson - Réponse

    I agree that using packing tape for a cracked screen should be included in this steps description. I don’t have wide but turned mine horizontal and that worked great.

    Mary Knapp - Réponse

    Bekomme die Oberschale einfach nicht runter! Trotz mehrmaligem erwärmen durch den iOpener und seitlichen bewegen! Weiß nicht mehr weiter!

    Stephan Lienhard - Réponse

    Wouldn’t that screw up the Touch ID?

    Rexx Havok - Réponse

  4. Tirez sur la ventouse pour créer un petit espace entre l'ensemble de l'écran et le boîtier arrière. Insérez l'extrémité plate d'une spatule (spudger) dans l'espace créé. L'adhésif étanche maintenant l'écran en place est très résistant, et créer ce premier espace demande de la force. Si vous avez des difficultés à ouvrir un interstice, bougez l'écran de bas en haut pour décoller l'adhésif jusqu'à ce que vous puissiez insérer une spatule (spudger).
    • Tirez sur la ventouse pour créer un petit espace entre l'ensemble de l'écran et le boîtier arrière.

    • Insérez l'extrémité plate d'une spatule (spudger) dans l'espace créé.

    • L'adhésif étanche maintenant l'écran en place est très résistant, et créer ce premier espace demande de la force. Si vous avez des difficultés à ouvrir un interstice, bougez l'écran de bas en haut pour décoller l'adhésif jusqu'à ce que vous puissiez insérer une spatule (spudger).

    This was SO hard for me to do with the spudger. I couldn’t get a gap to insert it because my phone was so cracked (even though I used tape on the front) to get a solid seal with the suction cup. I ended up taking a VERY thin knife and inserting it straight down to make the initial break that allowed me to insert the spudger.

    jessica harlow - Réponse

    I’ve given up using a plastic spudger to try to open any of these phones. I use a metal one with a flat base and a very sharp end…close to a razor. As long as I’m careful, it won’t slip and scratch the base. It’s much easier than using these plastic spudgers.

    mcr4u2 -

    I confirm that the plastic spudger it’s not the best tool for this operation. I suggest to use a larger metal tool like a “Jimmy” or “iSesamo open tool” (I used the first one)

    Cristef -

    Im trying to get the screen off right now and my phone is not cracked and its still a pain

    Jordon Johnson - Réponse

    Using a blow dryer was extremely helpful and using the suction cup towards one of the lower edges was also helpful

    Jordon Johnson - Réponse

    This is not working for me. How long does the heat need to be applied? Still trying right now…. =/

    Chris Gallego - Réponse

    Apply hair dryer for at least 1 minute. I inserted the tip end of a thin mini screwdriver and with some force, pryed it open and inserted my plastic spudger to continue the separation process. It worked, just be patient.

    Please wear protective glasses! My iPhone glass was severely cracked, when separating the glass a corner area of broken glass exploded in my face. Apply transparent tape over the broken glass to contain the shards.

    amberron - Réponse

    I second Jessica’s January 8 comment.  I just finished a battery replacement on my iPhone 7 and this step was the most nerve-wracking part.  I ended up using a sharper (but not razor-sharp) metal object to get this done with confidence (tried the spudger and guitar pick but not thin enough).  The tool I used was the exact duplicate of what iFixIt calls “iSesamo Opening Tool” in their tool selection.  I did the heat up with a hair dryer (after attempts with an iOpener hot pad) and the secret (as Jessica also noted)  was to not use the angle of attack shown in the pictures, but to push it in more vertically along the bottom edge while pulling up on the suction cup.  From there you can easily lever the tool to the lower angle-of-attack (as shown in the picture).  I actually used the metal tool for most of the perimeter as well, just don’t go deep (you don’t need to).  Notes: my display was intact, and I was able to pull up fairly hard with a glass screen protector still on it.

    Ted - Réponse

    This is frustrating. I heated the lower edge with a hair dryer for 1 min on high about 3-4 times. In between each heat cycle, I rocked the suction cup back and forth. I was eventually able to create significant space for the provided tool. This takes a lot of patience. Once the space was created, it was very easy to remove the screen.

    Dan - Réponse

    use a fingernail, then the blue tool, then the spudger

    Therese Peffer - Réponse

    The iOpener worked just fine for me. Had to keep it on for a few minutes. I also was able to get the suction cup seal right close to the edge, over top of the home button for added leverage. Used the blue tool and transitioned to the spudger. Slow, steady pressure…and patience. ;)

    johnhall918 - Réponse

    Unable to open an iPhone 7 display assembly. Used gell pack at 150 degrees F. The phone wouldn’t budge when I used the iFixit suction cut. Part of the problem is that the cup doesn’t adhere for long before it looses suction. I suspect it would work better on unbroken glass, but that doesn’t help me now. After spending a lot of time at this, I changed heating methods to a hot air heater. I raised the temp of the bottom end of the phone to, ultimately, 175 degrees, and used a variety of tools to try to pry the glass apart enough to get a spudger (or anything) in, but it didn’t even lift enough for a double-edged razor blade to get in. I’ve been trying this for hours now, and about to give up and throw a lot more money at this to have a service perform the work. I figured that 175 was as high as I should need to go to soften the adhesive without damaging the electronics. Should I have gone higher? I see no mention of measured temps in any instructions or comments.

    ted - Réponse

    Have you tried applying tape to the broken screen? This will help a lot with keeping the suction cup on it.

    Christian Groothuis -

    It doesn’t need to get very hot; pulling up on the display is mainly what does the trick. Make sure the two pentalobe screws have been removed and then try the tricks in this step. If all else fails, superglue the suction cup to your display and let it cure, and then pull. Keep in mind you only need a tiny gap to insert a plastic pick and start cutting the adhesive. Good luck!

    Jeff Suovanen -

    Just a question. After this operation the impermeability function was compromitted?

    bentek86 - Réponse

    The trick I found, was to add packing tape right across the bottom over the home button then use hairdryer on the end, then suction cup on the very bottom and it lifted enough to get a gap. No one mentioned how it would be impossible to handle the phone after the hairdryer ;)

    Andrew Lansdowne - Réponse

    Didn’t have an iOpener and 60 seconds on a hairdryer wasn’t doing it for me. Still wouldn’t budge. I had to take a very sharp razor along the seam at the bottom between the speakers. It took about 20 passes for it to separate enough to get the spudger in. Make sure you keep the razor at a 90-45˚ angle and that it goes no more than 1-2mm into the phone. The bottom of the phone is metal, but the casing for the screen is plastic. So if you cut lower than a 45˚ (flat with the phone) you risk cutting into the casing. Apply light pressure when making the passes. I would just do the razor on the flat part on the bottom.

    minimalist - Réponse

    I used a hair drier while lifting up at the same time until I could get the too inside. The seal is pretty finicky. Just take your time and you should be fine. Work the hair drier and the tool all the way around before lifting the screen up and off. There will likely be sealant stuck between the screen and phone. You can just break it with the tool.

    Ray Bieze - Réponse

    This step was impossible for me despite using a blow dryer and having no cracks on the screen. I finally took it to a local repair place and had them do battery replacements for two iPhone 7’s. The girl let me watch her do it. She used a razor blade (just until she had a small opening that she could hold open with her fingernail) and confirmed that she too would have difficulty opening it with a plastic tool and suction cup. The plastic tool was great for prying the rest of it open once a crack was there, but she said she would never try to use that as the tool to initially open it. The tools provided for initially prying open the screen are inadequate.

    Chad Twedt - Réponse

    Hopeless - no chance to get the screen off without any damage. No matter what tools, heat etc.

    Anatole Beams - Réponse

    I second what others have said, definitely use a razor blade to break the seal! Heat helps some, but too much direct heat is bad for the screen. Would have been impossible if I hadn’t read the comments, thanks everybody!

    Kit - Réponse

    Use extreme caution on this step. I was just replacing my battery and now i’m buying a new screen. The screen was very stuck, I pulled to hard and it popped off suddenly, completely destroying the screen.

    moose - Réponse

    When the right heat is reached, the easiest way is to use a metal iFlex to create the initial gap, then insert the Jimmy or iSesamo next to it so the gap gets bigger, at this point you can get in with the flat edge of a plastic spudger and slowly slide it in the borders to cut the adhesive. You will still need to force a bit the upper end to separate the screen by pulling it down while keeping up the screen, and twist to the right. I hope this is clear enough. Never apply too much strength too quickly anyway.

    Stefano Restuccia - Réponse

  5. Glissez le spudger vers la gauche le long du bord inférieur de l'iPhone. Tournez le spudger pour agrandir l'espace entre le boîtier arrière et l'écran. Tournez le spudger pour agrandir l'espace entre le boîtier arrière et l'écran.
    • Glissez le spudger vers la gauche le long du bord inférieur de l'iPhone.

    • Tournez le spudger pour agrandir l'espace entre le boîtier arrière et l'écran.

    Didn’t have an iOpener and 60 seconds on a hairdryer wasn’t doing it for me. Still wouldn’t budge. I had to take a very sharp razor along the seam at the bottom between the speakers. It took about 20 passes for it to separate enough to get the spudger in. Make sure you keep the razor at a 90-45˚ angle and that it goes no more than 1-2mm into the phone. The bottom of the phone is metal, but the casing for the screen is plastic. So if you cut lower than a 45˚ (flat with the phone) you risk cutting into the casing. Apply light pressure when making the passes. I would just do the razor on the flat part on the bottom.

    minimalist - Réponse

    I used a hairdryer and a razor

    Gina Torres - Réponse

    The photos are a con. You cannot get a spudger in unless you can lift the screen. You cannot lift the screen because of the adhesive. Using a anything metal will damage the paintwork or the glass edge.

    Anatole Beams - Réponse

    I agree, these guides are half imaginary idealism it seems. A thin metal edge pushed vertically down just a fraction of a mm will cause the adhesive to weaken better than any amount of heat, but affects the final appearance sadly.

    Jesse de Vries - Réponse

  6. Faites glisser la spatule le long du côté gauche en commençant par le bord inférieur et en travaillant vers les boutons de contrôle du volume et le commutateur du silencieux. Ne faites pas levier le long du bord supérieur de l'écran, vous risqueriez d'endommager les clips en plastique qui fixent l'écran. Ne faites pas levier le long du bord supérieur de l'écran, vous risqueriez d'endommager les clips en plastique qui fixent l'écran.
    • Faites glisser la spatule le long du côté gauche en commençant par le bord inférieur et en travaillant vers les boutons de contrôle du volume et le commutateur du silencieux.

    • Ne faites pas levier le long du bord supérieur de l'écran, vous risqueriez d'endommager les clips en plastique qui fixent l'écran.

    Be VERY careful on this next step going up the right side of the phone. There is a ribbon cable 1/3 of the way up from the bottom that is very close to the edge. Do NOT use the blue triangle!!!! Just lightly rotate the spudger to get separation on the edge.

    Timothy Varvais - Réponse

  7. Insérez l'extrémité plate d'une spatule (spudger) dans le coin inférieur droit de l'appareil. Bougez la spatule pour agrandir l'espace entre l'écran et le boîtier arrière. Faites glisser la spatule le long du bord droit du téléphone tout en défaisant l'adhésif qui maintient l'écran.
    • Insérez l'extrémité plate d'une spatule (spudger) dans le coin inférieur droit de l'appareil.

    • Bougez la spatule pour agrandir l'espace entre l'écran et le boîtier arrière.

    • Faites glisser la spatule le long du bord droit du téléphone tout en défaisant l'adhésif qui maintient l'écran.

    • Surtout, n'insérez pas la spatule plus profondément que la bande adhésive, pour éviter d'endommager les nappes très fragiles du côté droit.

  8. Tirez sur la ventouse pour soulever l'écran et ouvrir l'iPhone. Evitez de soulever l'écran à plus de 10°, des nappes relient l'écran à la carte mère le long du bord droit de l'appareil.
    • Tirez sur la ventouse pour soulever l'écran et ouvrir l'iPhone.

    • Evitez de soulever l'écran à plus de 10°, des nappes relient l'écran à la carte mère le long du bord droit de l'appareil.

    do not pull up pull sideways it will brake

    Riley Patterson - Réponse

    Made this mistake

    rachael.grime - Réponse

    Somehow my phone turned itself back on during the opening. Scared me a little, like a patient coming out of anesthesia during the operation. I was able to turn it back off. Gotta be more careful where you grab this thing.

    Bryant Larsen - Réponse

  9. Tirez sur la petite bosse afin de séparer la ventouse du panneau frontal.
    • Tirez sur la petite bosse afin de séparer la ventouse du panneau frontal.

  10. Faites glisser un médiator le long du bord supérieur de l'iPhone, entre le boîtier arrière et le panneau frontal pour briser l'adhésif restant qui maintient l'écran en place. Veillez à ne pas endommager les clips en plastique sur le bord supérieur du téléphone.
    • Faites glisser un médiator le long du bord supérieur de l'iPhone, entre le boîtier arrière et le panneau frontal pour briser l'adhésif restant qui maintient l'écran en place.

    • Veillez à ne pas endommager les clips en plastique sur le bord supérieur du téléphone.

    The plastic clips mentioned are on the top of the screen being replaced… so not sure why it matters not to break them. Trick here was to pull the screen downwards to open a gap at the top and then insert as shown and raise to break the seal.

    Andrew Lansdowne - Réponse

    This is relevant for other guides than the display replacement guide.

    jvalaamo -

  11. Kits pour Nintendo Switch

    Une solution rapide pour reprendre le jeu

    Acheter un kit pour Switch

    Kits pour Nintendo Switch

    Une solution rapide pour reprendre le jeu

    Acheter un kit pour Switch
  12. Eloignez légèrement l'écran complet du bord supérieur du téléphone pour dégager les clips le maintenant au boîtier arrière. Ouvrez l'iPhone en pivotant l'écran vers le haut en partant du côté gauche comme la couverture d'un livre. N'essayez pas encore de séparer l'écran complètement, car il y restent plusieurs nappes fragiles qui le relient à la carte mère de l'iPhone.
    • Eloignez légèrement l'écran complet du bord supérieur du téléphone pour dégager les clips le maintenant au boîtier arrière.

    • Ouvrez l'iPhone en pivotant l'écran vers le haut en partant du côté gauche comme la couverture d'un livre.

    • N'essayez pas encore de séparer l'écran complètement, car il y restent plusieurs nappes fragiles qui le relient à la carte mère de l'iPhone.

    I just broke the cable to the battery!

    No Bama - Réponse

    same dude im such a freak lol omg haha

    Aiden Polaski - Réponse

    Are there replacements ribbons?

    Blax Bently - Réponse

    Has anyone else noticed very small squares of rubber with a circle cut through it (I think they fall off into the phone when dismantling)?

    I just replaced my screen and worked out that these are actually a wee pocket that slips over the pentalobe screw holes on the replacement screen. I’m not sure if it’s an additional water resisting mechanism or if it’s to add additional traction for the screws

    richarddillon - Réponse

    Thanks, I was wondering where those were from!

    Albert -

    Same, I only had one fall out and I had no idea if important, and didn’t re-add - because I wasn’t sure where it fell from - but it was definitely from the home screen button….watch it be important. -__-

    Nicole Crome -

    I just broke cable connecting camera and earpiece speaker to logic board. Be careful with it.

    Natan Haładyn - Réponse

    This section is missing a critical step - to lay some Post-It notes or something below the right half of the phone when you swing it open, so the ribbon cables don’t get sliced by the sharp edge of the phone case. I broke the Home Button ribbon cable because there was no strain relief when I laid it open.

    neila - Réponse

    I also broke the home button cable and now I have to use assistive touch.

    Laurencio Gonzalez - Réponse

    Keep the suction cup on the display to keep it propped up while you disconnect the ribbon cables.

    minimalist - Réponse

    I broke the short ribbon cable that attaches underneath the lower connector bracket. Be SURE when you lift the display, you do it from left to right. I thought I had the phone oriented correctly in my hand, but I was mistaken.

    John Murray - Réponse

    Put the suction cup on the right side of the middle of the screen when you rotate it up and out. It serves as a nice stand to take the pressure off the connectors.

    Ray Bieze - Réponse

    no mention of what you do once u open the book. are the ribbons long enough to lie flat  or do we have to keep screen raised while removing screws,, like when we hold screen up 45 degrees while removing 5 screw plat when at top of phone. I only realised how fragile the ribbons are and how important it is to use suction  cup to rest screen on an angle so ribbons don't stretch or cut on frame.

    thanks for the above comments and probably the most important section. I just hope I closed t before I fdid any damage. its lke the fragility of iPhone 3’s all over again.

    scallyteacher - Réponse

    I just broke one of the cables… yeah, it is not nice… I’m lucky in the sense the screen is still working, but the button is not.

    Trying a cheap screen on Ebay (that contains the cable) do 20$, after that, it’s a new cellphone…

    Vincent Poirier - Réponse

    • Enlevez du support du connecteur inférieur les quatre vis tri-point Y000 aux longueurs suivantes :

    • Trois vis de 1,2 mm

    • Une vis de 2,4 mm

    • Tout au long de la réparation, gardez la trace de chaque vis et assurez-vous de la revisser exactement là où elle était pour éviter d'endommager votre iPhone.

    Ahhh shoot! accidentally ordered tri-wing vs tri-point (must have just looked for y000).. It seems they only did this to annoy repair folks because not everything is tri-point on the phone...

    Steve - Réponse

    These screws just spin for me. They don't back out, but the heads aren't stripped either. I've tried applying backpressure to help lift the screws, but no luck

    Jeff Hurst - Réponse

    The Y000 took out one of the screws but not the other 3. I even tried the PH000 as suggested but nothing.

    dbright - Réponse

    What driver do I need to remove these screws i’m stuck

    Nasser Nader - Réponse

    i cant use, the Y000 it isnt working.

    joscarlos91 - Réponse

    What if I stripped a screw what do I do??

    Jacob Ramos - Réponse

    Yep, only the 2.4mm came out, other 3 won’t budge, and worried I’ve stripped the heads. Anyone got any ideas?

    Stephen Babbage - Réponse

    It’s the screwdriver bit that is the problem. I had the same issue with 2 Y000 bits not grabbing the screw properly. I fixed it by using a small 3 sided file to slightly grind the groves in the Y000 bit just a bit deeper. Then the bit worked like a charm on these screws.

    Jim Staples - Réponse

    Use Y000 on all 4. U have to be very sensitive on the 1.2mm screws. Put the bit in the screw, put the left pointing finger on top of the screwdriver and turn the driver carefully to the right until you feel a “bump”, thats the trick :-), then you are able to screw the screw out.

    Magne Eivindson - Réponse

    For me the key here was a LOT of downward pressure to ensure the Y000 bit caught in the screw. Not sure i can describe how much exactly, but is was significant. Otherwise the bit would not catch.

    Erik Fredriksen - Réponse

    What do I do if I Stripped one of them?

    Adam Corral - Réponse

    Can’t get them removed what to do ?

    cowling_luke - Réponse

    Managed to get the central one out. The upper one won't move, the lower one I've popped out with some force. This allows you to rotate the cover enough to unplug the various bits. Not ideal, but works. I've tried applying a lot of pressure, using the tighten/ loosen method, but the heads have just got mashed… no wonder Samsung are now No1, sigh…

    jimpoolio - Réponse

    You need to be careful when just rotating the cover as you can accidentally slice through the two black antennas! You only need to nip them…As you can tell I have done this in the past :/

    Kyle Webb -

    The first, longer screw came out fine, but the other three wouldn’t budge, regardless of more/less pressure or a slight angle or anything. I finally filed down the tip of the Y000 bit ever so slightly, and then it worked. Hope this helps someone.

    Harmony Vine - Réponse

    Filing down the bit worked for me. The tip about putting an index finger on the end of the screwdriver handles and then turning gently until it clicks into place was very helpful! Using these 2 tips I didn't need much downward pressure. Screws are out in a few turns.

    Chris Bennett - Réponse

    If you can’t get the bit to grip the screw properly, you can use a little bit of the water-proof sealing between the bit and the screw. That worked for me. Hope this helps anyone.

    jvalaamo - Réponse

    Mine came out easily. I placed the screws in the area where the bit goes in my kit so I can keep track.

    Gina Torres - Réponse

    I used a bunch of medicine cups to track my screws. You need like 12 if you want them all in cups. I ran out. There are so many different sizes that literally vary by 1mm. The tolerances on these things are tight.

    Ray Bieze - Réponse

    I use a 28 day pill box and keep every screw separate and reburn to exact slot because they all vary in length, width and can really damage u phone if too long and nt secure if to small.  use a magnetised screwdriver,  or make the cheap freebees magnetic for a short period by rubbing it up an a magnet. lol

    scallyteacher - Réponse

    Absolutely ridiculous had to go get a different one just stupid

    mark golling - Réponse

    I couldn’t get the lowest one out and just turned the metal bracket out of the way and replaced battery.

    qwerty77x - Réponse

  13. Retirez le support du connecteur inférieur.
    • Retirez le support du connecteur inférieur.

    my battery cable connector was stuck to the bottom of this metal bracket plate so be careful when you lift it off

    Josh Martin - Réponse

    This may have been intentionally done by Apple to make sure the battery gets disconnected before any other connector is disconnected. So always make sure to disconnect the battery before disconnecting and reconnecting the connectors for the display.

    Oscar Moreno - Réponse

    So…I forgot to put this bracket back on when reassembling. Now I’ve adhered the display to the case and don’t have another adhesive strip…so I’m wondering: what purpose does this bracket serve? The phone is powering on and seems to work okay.

    Am I going to run into trouble with this bracket missing?

    Ian Fritz - Réponse

    Well, that didn’t last long. The phone shuts down without warning. So I guess that plate is important…

    Ian Fritz -

  14. Utilisez la pointe d'une spatule (spudger) pour soulever le connecteur de la batterie de sa prise sur la carte mère. Pliez légèrement la nappe du connecteur vers le haut pour éviter un contact avec la prise ce qui risquerait d'alimenter le téléphone. Pliez légèrement la nappe du connecteur vers le haut pour éviter un contact avec la prise ce qui risquerait d'alimenter le téléphone.
    • Utilisez la pointe d'une spatule (spudger) pour soulever le connecteur de la batterie de sa prise sur la carte mère.

    • Pliez légèrement la nappe du connecteur vers le haut pour éviter un contact avec la prise ce qui risquerait d'alimenter le téléphone.

    Was kann passieren wenn man diesses Kabel vergessen hat zu entfernen `?

    Julian Eltrich - Réponse

    Reconnecting the battery poorly can cause the iPhone to appear to be properly powered and functional, but then suffer a reboot loop.

    I had difficulty after a screen replacement, and the Console app on my Mac showed that the ‘thermalmonitord’ process was throwing lots of errors from not getting any sensor readings from the battery. It would never charge past 1% and just kept rebooting.

    The contacts on this conector looked fine so even though I had reseated this connector several times already, I reconnected it very firmly using my thumb and a spudger to really press all the corners and middle and really gave it a good massage and then finally it showed the normal dead battery screen and started properly charging and eventually booted back up to normal functionality.

    It seems the battery has to be able to transmit data to the phone to say it’s not overheating or iOS will not allow any current into the battery to recharge it, and the kernel will panic from the null readings and just reboot over and over again.

    jason - Réponse

  15. Assurez-vous que la batterie est déconnectée avant de déconnecter ou reconnecter les nappes de cette étape. Utilisez l'extrémité plate d'un spudger ou un ongle pour débrancher les deux connecteurs inférieurs de l'écran en les tirant tout droit hors de leur prise sur la carte mère. Pour reconnecter ces nappes, appuyez sur une extrémité jusqu'à ce qu'elle s'enclenche, puis répétez avec l'autre extrémité. Ne pas appuyer sur le milieu. Si le connecteur est même légèrement en désalignement, le connecteur peut se plier, causant des dommages permanents.
    • Assurez-vous que la batterie est déconnectée avant de déconnecter ou reconnecter les nappes de cette étape.

    • Utilisez l'extrémité plate d'un spudger ou un ongle pour débrancher les deux connecteurs inférieurs de l'écran en les tirant tout droit hors de leur prise sur la carte mère.

    • Pour reconnecter ces nappes, appuyez sur une extrémité jusqu'à ce qu'elle s'enclenche, puis répétez avec l'autre extrémité. Ne pas appuyer sur le milieu. Si le connecteur est même légèrement en désalignement, le connecteur peut se plier, causant des dommages permanents.

    • Si l'écran reste vierge, des lignes blanches apparaissent ou que le retour tactile manque complètement ou partiellement après que vous ayez remonté votre téléphone, essayez de déconnecter et reconnecter ces deux nappes, puis vérifiez qu'elles sont bien enclenchées.

    To be honest you don’t really need to disconnect the display cables in step 15 or 16 to get the battery out. Just keep the suction cup on the screen to keep it propped up and to give the cables some slack. The only reason to take these cables off is that it’s a pain to apply the replacement display adhesive with those cables in the way. If you’re not re-waterproofing your phone just leave these attached.

    Remplacement des bandes adhésives fixant l'écran d'un iPhone

    minimalist - Réponse

    MAKE SURE you hold the top screen when dislodging the cable connections. I let the screen lie flat down and ended up tearing one of the cable connections, now my touch ID does not work at all! I’m going to have to order a whole new screen.

    Arjun Nagarajan - Réponse

    Don’t miss that SECOND CONNECTOR like I did. It will break very easily if not disconnected :(

    garrett peek - Réponse

  16. Retirez les deux vis cruciformes de 1,3 mm fixant le support sur le connecteur de l'ensemble capteur du panneau avant. Retirez le support. Retirez le support.
    • Retirez les deux vis cruciformes de 1,3 mm fixant le support sur le connecteur de l'ensemble capteur du panneau avant.

    • Retirez le support.

    Has anyone had trouble getting these two screws off? I’ve been working on these for about 10 minutes and the LEFT screw wont spin. It seems like the little PH000 screwdriver bit won’t even grip it. (The one of the right comes off, no problem)

    It looks like I’ll have to pick this project up again with a screwdriver that will actually take off this piece.

    Makana Sylva - Réponse

    The right screw kept spinning, tried different levels of force but didn’t work. I left the screw on and bent the shield to get to the cable.

    s h - Réponse

    I used a #1 flat head tip to loosen.

    Peter Pearson - Réponse

    I couldn’t get the two screws out either—used the correct screw tip and everything. Stripped the screw. Will now attempt to just keep the cable attached…..

    Therese Peffer - Réponse

    Use the PH000 and apply a little more force before spinning, should come right out!

    Sierra Scolaro - Réponse

    ^To anyone having trouble, this is the correct answer. Put the phone on a firm surface, align your driver carefully, press down hard, and twist. As long as your driver is approximately the right size, it’ll come out.

    Jeff Suovanen -

    the two screw i have are stripped and i have n way of getting either screws off whats my next bet

    Alexis Marie Colon - Réponse

    The PH000 bit is to large. I can’t get the screws out either which really sucks…now I have to put everything back together, find another bit that will work and try this again another day. Not impressed with IFIXIT’s attention to detail so far :-(

    Ryan Welborn - Réponse

    Using iFixit’s driver kit, I prefer a PH00 for this, which is larger than the PH000. If you think the PH000 is too big, something is wrong.

    Jeff Suovanen -

    I think part of the issue with the iFixit PH000 is that it is slightly too pointy. The PH00 fits better because the splines engage the slots of the screw before the point bottoms out. The PH000 tip bottoms out in the screw’s center point and the splines don’t engage as well. I have other PH000 tips that are more blunt nose and they work better than the iFixit bit.

    rcarswell - Réponse

    Use the J00 bit. Worked perfectly

    efazio588 - Réponse

    PH000 screwdriver didn’t work for any of these screws, or the barometric vent, or the taptic engine. It was too big. I had to use a different screwdriver from another kit I had.

    minimalist - Réponse

    I’d do this step before removing the ribbon cables by the battery connector. That way you can disconnect all of them at the same time.

    Ray Bieze - Réponse

    i used the little +-shape 30 mm screwdriver (not the Y…but the + shape).

    mason - Réponse

    the cable tore. is that it i need a new phone?

    patricia loving - Réponse

    You don’t need a new phone, but your selfie camera and phone speaker will not work. You can get replacements for that about $10.

    jack jones - Réponse

    Reconnecting this cable and coverplate took a good 20 minutes. O_O

    Nicole Crome - Réponse

    What can I do to remove the screw (I stripped it)

    Alex Vu - Réponse

    I also had issues to loosen up the screws, in two parts the right side up and the left side down, i think the PH000 is to pointy or something or its too hard for the srews of the iphone, i cannot take it off and know im regreting i bought i order all the way from Paraguay in south america and know so angry it doesnt work

    Martin Frutos, Nuñez - Réponse

  17. Débranchez le connecteur de l'ensemble capteur du panneau avant, de sa prise sur la carte mère. Ce connecteur à pression devrait également être reconnecté une extrémité à la fois pour minimiser le risque de flexion.
    • Débranchez le connecteur de l'ensemble capteur du panneau avant, de sa prise sur la carte mère.

    • Ce connecteur à pression devrait également être reconnecté une extrémité à la fois pour minimiser le risque de flexion.

    Das ist sehr mutig, das Kabel dort so zu strapazieren.

    Mich würde das Display daneben stellen und mit irgendetwas stützen, dass es nicht umkippen kann um Beschädigungen an dem Kabel zu vermeiden. Das reißt sehr schnell ein.

    Detlef Menninger - Réponse

    Is this the connector for the earpiece, as well? I did the screen replacement and everything worked, except now I can’t use my earpiece… I’m afraid I didn’t fully connect this particular portion.

    Victor Bui - Réponse

    @victorbui714 Correct, this is also the connector for the earpiece speaker. Check the flex cable carefully and make sure it wasn’t pinched or torn. Make sure the connector socket is clean (give it a blast with some compressed air if needed) and try reseating it. If that doesn’t help, you may want to remove the earpiece speaker and inspect the four springs on the back, and check that they’re intact and making good contact with the four circular pads on the flex cable. Give the pads a wipe with some IPA and try not to leave any skin oils on them. If none of that works, try replacing the entire flex cable/sensor assembly. Good luck!

    Jeff Suovanen -

  18. Retirez l'écran complet.

    When removing the screen, be aware of the two tiny square black rubber grommets on the Penelope screw brackets that secure the screen. They can fall off very easily and be lost without even knowing it (it happened to me, but was lucky enough to find them).

    Guy Cooley - Réponse

    Sorry, I’m so unclear about when to replace the Adhesive tape. Should I put the iPhone 7 Display Assembly Adhesive at this step, or after I’ve replaced the battery?

    Victor Bui - Réponse

    @victorbui714 Battery first, then adhesive during reassembly, as it says in the instructions. ;)

    Jeff Suovanen -

    This is the 3rd screen iv put in my phone and everyone them bust at the top by the camera every time iv bought one of these screen idk if it’s the manufactures fault or what?

    trent bost - Réponse

    @trentb28922 Ouch! That’s not normal. Is your phone’s frame bent? Are you having to use a lot of force when you install the display?

    Jeff Suovanen -

  19. Retirez les trois vis cruciformes maintenant la fixation du haut-parleur interne au panneau avant :
    • Retirez les trois vis cruciformes maintenant la fixation du haut-parleur interne au panneau avant :

    • Deux vis de 2,6 mm

    • Une vis de 1,7 mm

    I am measuring the screws; my digital caliper measures both the top at 1.88mm not 2.6

    Marco Cueva - Réponse

    I just checked the screw measurements and they match what’s shown in the guide. Are you sure you’re looking at the right screws?Are you sure your caliper is accurate? Was your iPhone serviced in the past and reassembled incorrectly? Something isn’t right. The measurements here are the screw lengths, by the way—just in case you were measuring something else.

    Jeff Suovanen -

  20. Retirez la fixation du haut-parleur interne.
    • Retirez la fixation du haut-parleur interne.

  21. Soulevez la caméra frontale pour accéder au haut-parleur interne. Soulevez la caméra frontale pour accéder au haut-parleur interne.
    • Soulevez la caméra frontale pour accéder au haut-parleur interne.

  22. Retirez les deux vis cruciformes suivantes, fixant le haut-parleur interne au panneau frontal :
    • Retirez les deux vis cruciformes suivantes, fixant le haut-parleur interne au panneau frontal :

    • Une vis de 1,9 mm

    • Une vis de 2,5 mm

    Hi!What size is the third screw?

    Лёха Н - Réponse

  23. Retirez le haut-parleur interne.
    • Retirez le haut-parleur interne.

  24. Refaites chauffer votre iOpener et appliquez-le sur le bord supérieur de l'écran pour ramollir l'adhésif maintenant l'ensemble caméra frontale et capteur en place.
    • Refaites chauffer votre iOpener et appliquez-le sur le bord supérieur de l'écran pour ramollir l'adhésif maintenant l'ensemble caméra frontale et capteur en place.

    • Attendez environ deux minutes que l'adhésif soit bien ramolli avant de passer à l'étape suivante.

  25. Utilisez un spudger pour retirer délicatement le capteur de luminosité ambiante de son emplacement sur le panneau frontal. Essayez d'insérer entièrement votre outil sous le capteur pour l'éloigner de la pièce en plastique transparent juste en dessous. Si vous faites levier uniquement sur la nappe, le capteur risque de se détacher de la nappe et devra être remplacé. Si vous remplacez de toute façon l'ensemble capteur/nappe, cela n'a pas d'importance.
    • Utilisez un spudger pour retirer délicatement le capteur de luminosité ambiante de son emplacement sur le panneau frontal.

    • Essayez d'insérer entièrement votre outil sous le capteur pour l'éloigner de la pièce en plastique transparent juste en dessous. Si vous faites levier uniquement sur la nappe, le capteur risque de se détacher de la nappe et devra être remplacé. Si vous remplacez de toute façon l'ensemble capteur/nappe, cela n'a pas d'importance.

    I’m sorry to comment but this step is wrong. The proximity sensor is sticked to the display. I was following this instruction and the sensor was unvelded from the flex cable. Now it’s workless. It’s a fortune that the only problem with the iPhone is that while calling and holding the phone to the ear, the display doesn’t turn off.

    I recommend to gently pushing against the transparent plastic enclosure near the sensor and once it’s unsticked, keep pushing against the sensor’s body. In this way the sensor welding doesn’t bear/support any extra load on it.

    At least, my iPhone 7G had the sensor sticked to the display. Maybe some day I will replace it (around 20€ - 25€ on ebay)

    I won't claim to iFixit nor stop using this website. Whenever I higly recommend to iFixt technitians to revise such kind of “errors”. At least for expensive devices like Apple products.

    Miguel Cretu - Réponse

    I editted this guide and added these two comments. I already know about this “trick”. It’s your own decision to follow my suggestion or not.

    Miguel Cretu - Réponse

    I have fixed 2 screens now on iPhone 7. The 1st time I didn’t have this problem, 2nd time I did. I would agree with Miguel Cretu and save yourself the hassle and remove the sensor and it’s surround altogether.

    Wayne Lyell - Réponse

    In the second picture, there is the splugger that’s on it’s right is near a little window square, white inside. I’ve checked my replacement display and it don’t have inside in WHITE in this little window . Anyone know why have this color (it is not a sticker) and what is the reason? Thanks

    fakirox - Réponse

    I also had to pop out the clear plastic surround of the front camera to put into my new screen. It’s just glued in, so heat and pop it out with a spudger. Best to do this step last so you don’t accidentally tear any ribbons.

    Grant Barker - Réponse

    I actually found that removing the assembly from the other side (like the step 35) is a bit easier. Also, heat is really useful! I took an hair dryer, and for at least 3 minutes I heated by interval the piece, and at the end, the glue was so soft, it was really easy to remove!

    Vincent Poirier - Réponse

  26. Faites glisser le médiator vers le boîtier de la caméra frontale, en décollant l'adhésif qui fixe la nappe au panneau frontal. Arrêtez juste avant les vis. Faites glisser le médiator vers le boîtier de la caméra frontale, en décollant l'adhésif qui fixe la nappe au panneau frontal. Arrêtez juste avant les vis. Faites glisser le médiator vers le boîtier de la caméra frontale, en décollant l'adhésif qui fixe la nappe au panneau frontal. Arrêtez juste avant les vis.
    • Faites glisser le médiator vers le boîtier de la caméra frontale, en décollant l'adhésif qui fixe la nappe au panneau frontal. Arrêtez juste avant les vis.

  27. Utilisez le médiator pour dégager la nappe de la caméra des deux dispositifs en plastique sur le panneau frontal et pour la décoller du dernier adhésif. Utilisez le médiator pour dégager la nappe de la caméra des deux dispositifs en plastique sur le panneau frontal et pour la décoller du dernier adhésif. Utilisez le médiator pour dégager la nappe de la caméra des deux dispositifs en plastique sur le panneau frontal et pour la décoller du dernier adhésif.
    • Utilisez le médiator pour dégager la nappe de la caméra des deux dispositifs en plastique sur le panneau frontal et pour la décoller du dernier adhésif.

    на рисунке №2 винт 3 отсутствует, на рисунке № 3 винт 3 присутствует. нет описание где он был вывинчен. последний винт с правой стороны, около камеры

    Vitaly Savin - Réponse

  28. Retirez la caméra frontale et la nappe de capteur.
    • Retirez la caméra frontale et la nappe de capteur.

    Look at the camera assembly closely. There are two cables soldered together. Do not separate the pieces by mistake . Get the pick all the way below both ,and they will come off together.

    turboduck2 - Réponse

    Good statement I made that mistake on my first iPhone 7 Plus !

    Jaye - Réponse

    Its not mentioned here but there is a small philips screw at the top left that you may have to transfer to your new lcd panel

    Steve - Réponse

    Hi Steve, what is the main work of this little strip with 2 small contact? Antenna? Shield?

    Thanks

    fakirox -

    I’ve separated the sensor and front facing camera, can I just press them back together or will I need a complete replacement

    Dominic Sore - Réponse

    About Steve comment, anyone know what is this small screw with two contact? It is an antenna ?? Shield??? Thanks

    fakirox - Réponse

    I’m also looking for info on the screw on the immediate left of the top left corner of the speaker. Did you find the info out?

    Cheers!

    Mike Grandbois - Réponse

Conclusion

Pour réassembler votre appareil, suivez ces instructions dans l'ordre inverse.

102 autre(s) ont terminé cette réparation.

Merci à ces traducteurs :

100%

Ces traducteurs nous aident réparer le monde ! Vous voulez contribuer ?
Commencez à traduire ›

Evan Noronha

Membre depuis le 05/02/2015

193 056 Réputation

178 tutoriels rédigés

Équipe

iFixit Membre de l'équipe iFixit

Community

124 membres

11 798 tutoriels rédigés

18 commentaires

Question ..... I have a clear square plastic piece (open in the center) with a tab on one side. What is that for?

Mike McCleery - Réponse

Holds the lens in place.

Edward L Johnson III -

No that is for the ambient light sensor. LCD replacements come with it already installed on em’, so you can toss it if you see it on the replacement already. The larger, circular plastic piece is for the lens.

Brandon Neves -

Does the iPhone 7 plus Front Camera and Sensor Cable Replacement has to do anything with the earpieces speaker? i have replace my iphone 7 plus screen and front camera and sensor cable replacement and speaker and it still doesn’t work. what could really be wrong with my iphone 7 plus?

Saleka Chang - Réponse

Awesome tutorial, thank you! I couldn’t have replaced my camera without this! Well I could have but not the right way!!

Cynthia Hollingsworth - Réponse

Hi so i was replacing my screen when this ribbon ripped. Until I can get the part in the mail is there anything else that having this ribbon ripped will do or effect?

herron.tara4 - Réponse

Hiya, I do not believe so. I damaged the ribbon, no obvious signs but must of as worked when the new one was plugged in and it did not appear to have any affect on anything else. Hope this helps.

Charleigh B -

I ripped the cable in half and was able to use my phone fine for two weeks until I had the part in hand and time to make the replacement. Calls had to be on speaker or in headphones, and I needed to manually adjust my screen brightness throughout the day. You also won't have a selfie cam.

rJ Jarecki -

I replaced my friends screen after he smashed it, must of damaged the cable as once put together the phone was on Apple logo and could not get it to turn on. Had a feeling it was the sensor and it was. Ordered a new one from Amazon and turned on straight away.

The phone would not turn on with the old one plugged in or not so couldn't be 100% but it worked and now have a happy friend. Luckily I didn't restore the phone too!

Charleigh B - Réponse

I bought the replacement from iFixit, and afterwards, the selfie camera didn’t work. and the reason for the replacement was to fix the speaker problem, because I count really understand anymore the phone calls and it also didn’t change the problem. Also the speaker was replaced with an ifixit part. and now the Touch ID is also not working.

Michael Blechinger - Réponse

the flex of iphone 7 plus are compatible with the iphone 7?

Rolando Queral - Réponse

I am looking at doing this replacement because I am having trouble with siri hearing me. I believe the earpiece microphone is in this cable but it is not listed on the part description. Can anyone verify this?

Nick P - Réponse

In this image, the microphone is the gold rectangle with the foam pad on top. You can see it being separated from the screen in Step 27.

Jeff Suovanen -

Replaced the camera, but now my microphone does not work. I can listen to voicemails from both the top and loud speaker, as well as sound over the lightning and Bluetooth connection. A pair of headphones (external mic?) Will not enable phone calls or voice recorder, but will let me listen to music.

Any thoughts on resolving this issue?

rJ Jarecki - Réponse

Double-check the connectors and re-seat them; check for damage to the cables; remove the part and make sure the microphone isn’t blocked by adhesive or other debris. If all else fails, try installing the old part (or replacing it a second time) in case you received a defective microphone. Good luck!

Jeff Suovanen -

Ho sostituito la fotocamera frontale del mio IPhone 7 Plus ma adesso se faccio una foto o un video dal app fotocamera funziona perfettamente mentre se provo a fare una video chiamata con whatsapp, messenger o altre app non funziona, come mai?

PakyScat - Réponse

I replaced the front camera of my IPhone 7 Plus but now if I take a photo or video from the camera app it works perfectly while if I try to make a video call with whatsapp, messenger or other apps it does not work, can you help?

PakyScat - Réponse

Is it possible to repurpose an iPhone 6 or iPhone 6s front camera, to install it in an iPhone7

Kwame S - Réponse

Ajouter un commentaire

Afficher les statistiques:

Dernières 24 heures : 91

7 derniers jours : 501

30 derniers jours : 2,503

Total : 98,312