Modifications de Apple Watch Series 6 Battery Replacement en attente
ZH
Remarque : accepter ou refuser toute modification s’applique implicitement à toute modification précédente en attente de la même étape ou introduction.
|
|
0-black-Use a pair of [product|IF145-020|tweezers] to remove the metal shield covering the battery connector. |
| - | [* black] 用镊子去除覆盖电池连接器的金属屏蔽层。 |
|---|
| + | [* black] 用[product|IF145-020|镊子|new_window=true]去除覆盖电池连接器的金属屏蔽层。 |
|---|
|
Chose
|
Battery |
|
Titre
|
Apple Watch Series 6 Battery Replacement |
|
Introduction
|
Use this guide to replace a worn-out or dead battery in your Apple Watch Series 6.
This guide shows the procedure on the cellular/LTE version of the watch, but the GPS-only version is similar.
'''Note: The battery replacement procedure for the 40 mm Series 6 Apple Watch differs slightly from the 44 mm version.''' This guide shows how to replace the battery for both sizes.
Before you begin, make sure you have the appropriate replacement battery for your watch.
If your battery is swollen, [[What to do with a swollen battery|take appropriate precautions|new_window=true]]. For your safety, '''discharge your battery below 25%''' before disassembling your watch. This reduces the risk of a dangerous thermal event if the battery is accidentally damaged during the repair.
You’ll need replacement adhesive to reattach components when reassembling the device. |
|
Conclusion
|
If possible, turn on your device and test your repair before installing new adhesive and resealing.
[guide|113604|Secure the new battery with pre-cut adhesive|new_window=true] or double-sided adhesive tape. In order to position it correctly, apply the new adhesive into the device at the places where the old adhesive was located, not directly onto the battery. Press the new battery firmly into place.
To reassemble your Apple Watch Series 6, follow these instructions in reverse order. Apply a little bit of high isopropyl alcohol (>90%) to a Q-tip or use a cleaning pad to gently remove the leftover adhesive on the edges of the watch case and the screen before installing new adhesive.
For optimal performance, [[Battery Calibration|calibrate your newly installed battery|new_window=true]] after completing this guide.
Take your e-waste to an [[E-Waste|R2 or e-Stewards certified recycler|new_window=true]].
Repair didn’t go as planned? Try some [[Troubleshooting Problems After a Repair|basic troubleshooting|new_window=true]], or ask our [link|https://www.ifixit.com/Answers/Device/Apple%20Watch%20Series%206|Answers community] for help. |
|
Introduction |
| 使用本指南更换 Apple Watch Series 6 的衰减电池或损坏的电池。 | | | 本指南显示的是蜂窝版手表的更换步骤，但GPS 版手表的更换步骤与此类似。 | | | '''注：40 毫米 Series 6 Apple Watch 的电池更换步骤与 44 毫米版本略有不同。'''本指南说明了如何更换两种尺寸的电池。 | | | 开始之前，请确保您有适合手表的更换电池。 | | | 如果电池肿胀，[[[What to do with a swollen battery|采取适当的预防措施|new_window=true]]。为了您的安全，请在拆卸手表前将电池放电至 25% 以下。如果电池在维修过程中意外损坏，这将降低发生危险热事件的风险。 | | | 重新组装设备时，您将需要替换粘合剂来重新连接部件。 |
|
|
Conclusion |
| 如果可能，在安装新粘合剂和重新密封之前，请打开设备并测试修复效果。 | | | [guide|113604|使用预切粘合剂|new_window=true]或双面胶带固定新电池。为了正确定位，请将新粘合剂涂在旧粘合剂的位置，而不是直接涂在电池上。将新电池按紧到位。 | | 要重新组装 Apple Watch Series 6，请按照相反的顺序进行操作。在安装新粘合剂之前，用 Q 型吸头沾取少量高浓度异丙醇用棉签沾取少量高浓度异丙醇（>90%）或使用清洁垫轻轻去除表壳边缘和屏幕上残留的粘合剂。 | | | 为获得最佳性能，请在完成本指南后[[Battery Calibration|校准新安装的电池|new_window=true]]。 | | | 将您的电子垃圾送到[[E-Waste|R2 或 e-Stewards 认证的回收商|new_window=true]]。 | | | 维修没有按计划进行？请尝试一些[[Troubleshooting Problems After a Repair|基本疑难解答|new_window=true]]，或向我们的[link|https://www.ifixit.com/Answers/Device/Apple%20Watch%20Series%206|答疑社区]寻求帮助。 |
|