Réparez vos affaires

Droit à la réparation

Pièces & Outils

Canon PowerShot SD1000 LCD Screen Replacement

Rédigé par : Phillip Phung (et 7 autres contributeurs)
  • Commentaires : 1
  • Favoris : 0
  • Réparations terminées : 2

Difficulté

Modérer

Étapes

12

Sections

3

Drapeaux

2

Grammar Police

Police de grammaire

Réveillez le prof qui sommeille en vous et aidez-nous à améliorer l'orthographe de ce tutoriel !

Needs Better Images

A besoin de meilleures images

De meilleures photos amélioreront ce tutoriel. Aider en proposant de nouvelles photos!

Outils

Acheter ces outils

Pièces

Aucune pièce spécifiée.

  1. Remove the two screws from the side panel closest to the camera lens. Note: These screws are 2.9 mm long.

    • Remove the two screws from the side panel closest to the camera lens.

    • Note: These screws are 2.9 mm long.

    Traduire

  2. Remove the two screws from the camera bottom panel.

    • Remove the two screws from the camera bottom panel.

    • Note: These screws are 2.9 mm long.

    Traduire

  3. Remove the 2 screws from the side panel farthest from the lens.

    • Remove the 2 screws from the side panel farthest from the lens.

    • Note: These screws are 2.9 mm long.

    Traduire

  4. Pull the back panel away from the camera body, starting at the end with the function buttons.

    • Pull the back panel away from the camera body, starting at the end with the function buttons.

    Traduire

  5. Manta Precision Bit Set

    112 embouts pour toute réparation.

    Upgrade Your Toolbox

    Manta Precision Bit Set

    Upgrade Your Toolbox

  6. Remove the small cover panel and attached wrist strap mount.

    • Remove the small cover panel and attached wrist strap mount.

    Traduire

  7. Remove the front cover by gently pulling it away from the camera body.

    • Remove the front cover by gently pulling it away from the camera body.

    Traduire

  8. Place the front cover, back cover, and wrist strap mount in a safe place until you are ready for reassembly.

    • Place the front cover, back cover, and wrist strap mount in a safe place until you are ready for reassembly.

    Traduire

  9. Remove the 2 screws located at the top of the LCD panel.

    • Remove the 2 screws located at the top of the LCD panel.

    • Note: These screws are 2.4 mm long.

    Traduire

  10. Pull up the metal frame surrounding LCD screen starting at the side of the camera. Pull up the metal frame surrounding LCD screen starting at the side of the camera.

    • Pull up the metal frame surrounding LCD screen starting at the side of the camera.

    Traduire

  11. Push the metal frame away from the metal tab using the spudger, to detach the frame.

    • Push the metal frame away from the metal tab using the spudger, to detach the frame.

    • Rotate the metal frame upwards.

    • Note: The metal framing should be attached by a metal tab towards the bottom of the camera, near the function buttons.

    Traduire

  12. Carefully lift the metal frame from the camera. Remove the black LCD screen, leaving the thin lens pieces in place.

    • Carefully lift the metal frame from the camera.

    • Remove the black LCD screen, leaving the thin lens pieces in place.

    • Note: BE CAREFUL, both components are attached by an orange connector ribbon and cannot be removed yet!

    Traduire

  13. Carefully pull on the orange connector ribbon to disconnect the LCD screen. The LCD screen can be pulled out of the frame before disconnecting its connector ribbon. Note: Tweezers are helpful to disconnect the ribbon

    • Carefully pull on the orange connector ribbon to disconnect the LCD screen.

    • The LCD screen can be pulled out of the frame before disconnecting its connector ribbon.

    • Note: Tweezers are helpful to disconnect the ribbon

    Traduire
Conclusion

To reassemble your device, follow these instructions in reverse order.

2 autre(s) ont terminé cette réparation.

Auteur

avec 7 autres contributeurs

Phillip Phung

Membre depuis le 19/01/2012

486 Réputation

9 tutoriels rédigés

Badges: 10

+ 7 badges supplémentaires

Équipe

Cal Poly, Team 8-18, Maness Winter 2012 Membre de l'équipe Cal Poly, Team 8-18, Maness Winter 2012

CPSU-MANESS-W12S8G18

4 membres

10 tutoriels rédigés

Un commentaire

Ajouter un commentaire

Very helpful. These units still sell for a lot more than the cost of the replacement LCD

George Francis - Réponse

Ajouter un commentaire

Afficher les statistiques:

Dernières 24 heures : 1

7 derniers jours : 1

30 derniers jours : 4

Total : 2,711