Canon PowerShot SD1000 Motherboard Replacement

Phillip Phung et 5 autres contributeurs

Dernière mise à jour le January 28, 2014

30 minutes

Modérée

A besoin de meilleures images

Ce dont vous avez besoin

Outils

Étape 1 Back Panel

Canon PowerShot SD1000 Motherboard Replacement, Back Panel: étape 1, image 1 de 2

Canon PowerShot SD1000 Motherboard Replacement, Back Panel: étape 1, image 2 de 2

Remove the two 2.9 mm screws from the side panel closest to the camera lens.

Modifier

Étape 2

Remove the two 2.9 mm screws from the camera bottom panel.

Modifier

Étape 3

Remove the two 2.9 mm screws from the side panel farthest from the lens.

Modifier

Étape 4

Pull the back panel away from the camera body, starting at the end with the function buttons.

Modifier

Étape 5

Remove the small cover panel and the attached wrist strap mount.

Modifier

Étape 6 Front Case

Canon PowerShot SD1000 Motherboard Replacement, Front Case: étape 6, image 1 de 1

Remove the front cover by gently pulling it away from the camera body.

Modifier

Étape 7

Place the front cover, back cover, and wrist strap mount in a safe place until you are ready for reassembly.

Modifier

Étape 8 LCD Screen

Canon PowerShot SD1000 Motherboard Replacement, LCD Screen: étape 8, image 1 de 1

Remove the two 2.4 mm screws located at the top of the LCD panel.

Modifier

Étape 9

Pull up the metal frame surrounding the LCD screen starting at the side of the camera.

Modifier

Étape 10

Push the metal frame away from the metal tab using the spudger to detach the frame.
Rotate the metal frame upwards.
The metal framing should be attached by a metal tab towards the bottom of the camera, near the function buttons.

Modifier

Étape 11

Carefully lift the metal frame from the camera.
Remove the black LCD screen, leaving the thin lens pieces in place.
BE CAREFUL; both components are attached by an orange connector ribbon and cannot be removed yet.

Modifier

Étape 12

Canon PowerShot SD1000 Motherboard Replacement: étape 12, image 3 de 3

Outil utilisé dans cette étape :

Tweezers

$4.99

Ajouter au panier

Carefully pull on the orange connector ribbon to disconnect the LCD screen.
The LCD screen can be pulled out of the frame before disconnecting its connector ribbon.
Tweezers are helpful to disconnect the ribbon.

Modifier

Étape 13 Flash Unit

Canon PowerShot SD1000 Motherboard Replacement, Flash Unit: étape 13, image 1 de 2

Canon PowerShot SD1000 Motherboard Replacement, Flash Unit: étape 13, image 2 de 2

Slide the metal frame off of the camera on the side that is closest to the flash mechanism.

Modifier

Étape 14

Use a Phillips #00 screwdriver to remove the 2.4 mm screw that secures the flash assembly.

Modifier

Étape 15

Use the spudger to gently and carefully disconnect the flash assembly ribbon from the black connector lock.

Modifier

Étape 16

Pull the flash assembly forward out of the camera to remove it.
BE CAREFUL when handling the flash assembly. Touching the capacitor (the black cylinder attached to the flash assembly) could shock you.

Modifier

Étape 17 Shutter Button

Canon PowerShot SD1000 Motherboard Replacement, Shutter Button: étape 17, image 1 de 2

Canon PowerShot SD1000 Motherboard Replacement, Shutter Button: étape 17, image 2 de 2

Using the spudger, take off the shutter button by prying the small tab on the front side of the camera.

Modifier

Étape 18 Lens

Canon PowerShot SD1000 Motherboard Replacement, Lens: étape 18, image 1 de 1

Remove the 2.90mm screw from the lens, near the motherboard.

Modifier

Étape 19

Using the spudger remove the shutter button by prying the small tab on the front side of the camera.

Modifier

Étape 20

With a spudger disconnect the orange connector ribbon as shown.
Disconnect the orange connector ribbon that is located under the now removed shutter button.

Modifier

Étape 21

Remove the two 2.90 mm screws from the motherboard.

Modifier

Étape 22

Outil utilisé dans cette étape :

Tweezers

$4.99

Ajouter au panier

With Tweezers detach the bottom orange ribbon.

Modifier

Étape 23

Remove the screws shown. Start with the outside 6 (3-2.90mm & 3-2.40mm) screws on the metal frame. Then remove the 6 (2.40mm) screws on the back of the lens piece

Modifier

Étape 24

With spudger gently remove the Viewfinder Window that is directly above the lens.

Modifier

Remove screw attaching viewfinder piece to lens framing.

Adam Biesok - 3 sept. 2012 Réponse

Étape 25

Canon PowerShot SD1000 Motherboard Replacement: étape 25, image 3 de 3

Detach the mother board with lens from body of camera.
Carefully remove the lens from the motherboard. Use tweezers to remove any of the 4 connecting ribbons from the lens.
Your lens has been removed from the motherboard and bottom framing.