Réparez vos affaires Communauté Boutique

Canon Powershot SX10 IS LCD Screen Replacement

Introduction

The LCD screen is a monitor for the camera. It will display the photos before, during, and after capturing a picture. It also is used for changing settings easily. It does not operate in all camera modes. This guide will go through the steps needed to change the LCD screen if it is broken.

Ce dont vous avez besoin

  1. Canon Powershot SX10 IS LCD Screen Replacement, Lithium Ion Battery: étape 1, image 1 de 1

    • Open the door. Release the catch by sliding it towards the side of the camera.

    • Then slide the door towards the front of the camera.

    Traduire

  2. Canon Powershot SX10 IS LCD Screen Replacement: étape 2, image 1 de 3 Canon Powershot SX10 IS LCD Screen Replacement: étape 2, image 2 de 3 Canon Powershot SX10 IS LCD Screen Replacement: étape 2, image 3 de 3

    • Remove AA batteries.

    • Using a fingernail or iFixit opening tools to pry up the battery cradle.

    • Remove CR1220 battery from the cradle.

    Traduire

  4. Canon Powershot SX10 IS LCD Screen Replacement, LCD Screen: étape 3, image 1 de 2 Canon Powershot SX10 IS LCD Screen Replacement, LCD Screen: étape 3, image 2 de 2

    • Remove all four screws on the corners of the screen cover.

    • Gently pry open the cover with a fingernail or iFixit opening tool.

    Traduire

  5. Canon Powershot SX10 IS LCD Screen Replacement: étape 4, image 1 de 3 Canon Powershot SX10 IS LCD Screen Replacement: étape 4, image 2 de 3 Canon Powershot SX10 IS LCD Screen Replacement: étape 4, image 3 de 3

    • Remove two screws holding on the cover plate on the pivot.

    • Remove the cover plate using an iFixit opening tool.

    • You may need to loosen the bottom first, then pry on the top of the cover plate.

    • Remove the two screws on top of the swivel arm. These two screws will be separated by the pivot point.

    Traduire

  6. Canon Powershot SX10 IS LCD Screen Replacement: étape 5, image 1 de 3 Canon Powershot SX10 IS LCD Screen Replacement: étape 5, image 2 de 3 Canon Powershot SX10 IS LCD Screen Replacement: étape 5, image 3 de 3

    • Remove grounding wire, then continue to remove the screws holding the screen and front cover plate on.

    • The screen and plate will drop after removing the last screw.

    Traduire

  7. Canon Powershot SX10 IS LCD Screen Replacement: étape 6, image 1 de 2 Canon Powershot SX10 IS LCD Screen Replacement: étape 6, image 2 de 2

    • Unlatch the ribbon strip and power wires from the circuit board.

    Traduire
Conclusion

To reassemble your device, follow these instructions in reverse order.

Une autre personne a terminé cette réparation.

Auteur

avec 3 autres contributeurs

garrett knox

Membre depuis le 04/05/19

339 Réputation

2 tutoriels rédigés

Badges: 8

+ 5 badges supplémentaires

Équipe

Oregon Institute of Technology, Team S2-G6, Lancaster Spring 2019 Membre de l'équipe Oregon Institute of Technology, Team S2-G6, Lancaster Spring 2019

OIT-LANCASTER-S19S2G6

3 membres

5 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 1

7 derniers jours : 6

30 derniers jours : 32

Total : 1,279