Introduction

This guide shows how to replace a broken or cracked display assembly for the Moto Z. The display assembly includes the front glass and the AMOLED display.

The display assembly is extremely fragile and has no reinforcement. Work slowly and methodically when handling the display assembly.

If your display glass is cracked, keep further breakage contained and prevent bodily harm during your repair by taping over the glass.

Heat an iOpener and apply it to the left edge of the phone for at least 90 seconds.
  • Heat an iOpener and apply it to the left edge of the phone for at least 90 seconds.

  • A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the phone—the OLED display and internal battery are both susceptible to heat damage.

  • As you're waiting for the adhesive to soften, move on and read the following step to get an idea of where to pry.

Ajouter un commentaire

In the following steps you will be cutting through the adhesive around the edge of the display assembly.
  • In the following steps you will be cutting through the adhesive around the edge of the display assembly.

  • To avoid damage, do not cut in the following areas:

    • The OLED panel

    • The home button

    • The flash unit

Ajouter un commentaire

  • Apply a suction cup as close to the heated edge as possible.

  • Lift on the suction cup and insert the tip of an opening pick into the gap.

  • Do not insert the pick more than 1/16" (1.5 mm). Doing so may damage the OLED panel.

Ajouter un commentaire

  • Carefully slide the tip of the opening pick down and up the side of the phone, making sure not to cut deeper than 1/16" (1.5 mm).

  • As you run the pick along the side, you will feel the tip of the pick press against the edge of the OLED panel. That is as far as the pick should go without damaging the panel.

  • Once you have separated the adhesive, leave an opening pick in the side to keep the adhesive from resealing.

Ajouter un commentaire

  • Repeat the heating, lifting, and cutting steps for the remaining long edge of the phone.

Ajouter un commentaire

Ajouter un commentaire

  • Insert an opening pick into the flash side corner of the phone and carefully slice around the flash unit.

  • Do not insert the pick more than 1/16" (1.5 mm) into the edge.

  • Once you are done cutting, leave the pick in the corner to prevent the adhesive from resealing.

Ajouter un commentaire

  • Insert an opening pick into the remaining top corner of the phone.

  • Carefully slice through the adhesive across the top of the phone.

    • Do not insert the pick beyond 1/2" (12.5 mm).

Ajouter un commentaire

  • Apply a heated iOpener to the bottom edge of the phone for at least 90 seconds.

Ajouter un commentaire

  • Insert an opening pick into a bottom corner and slice towards the home button, stopping before you reach it.

  • Once you're done with the corner, leave a pick in place to prevent the adhesive from sealing.

  • Repeat the process for the other bottom corner.

Ajouter un commentaire

  • Carefully twist the first opening pick slightly to help release the edge adhesive.

  • Repeat the same process for each remaining pick, moving them as necessary and twisting slightly to release the adhesive.

Ajouter un commentaire

  • Lift the home button end of the display up to provide access to the display cables.

  • Do not swing the display beyond 90 degrees, and always support the display panel.

Ajouter un commentaire

  • Use the point of a spudger to pry the display cable shield up.

  • Remove the display cable shield.

Ajouter un commentaire

  • Use the point of the spudger to lift and disconnect the display cable connector from its socket.

Ajouter un commentaire

  • Remove the display assembly.

  • Before you reinstall the display assembly, thoroughly remove any remaining adhesive and glass from the frame.

    • After removing all traces of glue and glass from the frame, clean the adhesion areas with 90% (or higher) isopropyl alcohol and a lint-free cloth or coffee filter.

  • Be sure to turn on your phone and test your repair before installing new adhesive and resealing the phone.

  • To reseal your phone, use high-bond double-sided tape, such as Tesa 61395.

Ajouter un commentaire

  • Use tweezers to peel off the yellow tape securing the home button connector.

Ajouter un commentaire

  • Use tweezers to peel off the yellow tape securing the home button to the display assembly.

Ajouter un commentaire

  • Use the point of a spudger to flip up the home button connector's lock.

Ajouter un commentaire

  • Use tweezers to carefully pull the home button cable straight out of the socket.

Ajouter un commentaire

  • Remove the home button.

Ajouter un commentaire

Conclusion

Compare your new replacement part to the original part. You may need to transfer remaining components or remove adhesive backings from the new part before installing.

To reassemble your device, follow these instructions in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Check out our Motorola Moto Z Answers community for troubleshooting help.

4 autre(s) ont terminé cette réparation.

Arthur Shi

Membre depuis le 03/01/2018

18 148 Réputation

164 tutoriels rédigés

Équipe

iFixit Membre de l'équipe iFixit

Community

109 membres

6 204 tutoriels rédigés

Do you ship to India?

gsriram72 - Réponse

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 6

7 derniers jours : 70

30 derniers jours : 299

Total : 1,351