Aller au contenu principal

Introduction

You need a T5 screwdriver to remove the screws.

Pièces

Aucune pièce spécifiée.

  1. In order to remove the back cover, you must press the indicated button.
    • In order to remove the back cover, you must press the indicated button.

  2. With the button pressed, apply light pressure and slide the back cover off. This will allow you to access the battery
    • With the button pressed, apply light pressure and slide the back cover off.

    • This will allow you to access the battery

  3. In order to remove the battery, pull it out from the same side that the rubber button is on.
    • In order to remove the battery, pull it out from the same side that the rubber button is on.

  4. Using a plastic opening tool, separate the back cover from the phone. Using a plastic opening tool, separate the back cover from the phone. Using a plastic opening tool, separate the back cover from the phone.
    • Using a plastic opening tool, separate the back cover from the phone.

  5. Continue along the edge with the plastic opening tool. Continue along the edge with the plastic opening tool.
    • Continue along the edge with the plastic opening tool.

  6. Fix Kits pour Android

    A new screen or battery is one kit away.

    Acheter maintenant

    Fix Kits pour Android

    A new screen or battery is one kit away.

    Acheter maintenant
  7. Gently, remove the back cover. Gently, remove the back cover. Gently, remove the back cover.
    • Gently, remove the back cover.

  8. Unscrew the indicated screws using the T5 screwdriver. Unscrew the indicated screws using the T5 screwdriver. Unscrew the indicated screws using the T5 screwdriver.
    • Unscrew the indicated screws using the T5 screwdriver.

  9. Open the phone up and use the plastic opening tool to remove the cover to the keyboard. Be careful not to break the plastic during this step; do your best not to force anything.
    • Open the phone up and use the plastic opening tool to remove the cover to the keyboard.

    • Be careful not to break the plastic during this step; do your best not to force anything.

  10. The button board will be loose once the cover is removed. Lift it up to reveal the sensor board.
    • The button board will be loose once the cover is removed.

    • Lift it up to reveal the sensor board.

  11. With the T5 Screwdriver, remove the marked screws. With the T5 Screwdriver, remove the marked screws.
    • With the T5 Screwdriver, remove the marked screws.

  12. With the screws removed, the sensor board should be free to flip up. With the screws removed, the sensor board should be free to flip up.
    • With the screws removed, the sensor board should be free to flip up.

  13. Disconnect the wire with the plastic opening tool. Disconnect the wire with the plastic opening tool.
    • Disconnect the wire with the plastic opening tool.

  14. Remove the screws marked. The Screw on the left is located underneath the cable. With those screws removed, the circuit board and sensor board will be detached from the rest of the phone.
    • Remove the screws marked.

    • The Screw on the left is located underneath the cable.

    • With those screws removed, the circuit board and sensor board will be detached from the rest of the phone.

Conclusion

To reassemble your device, follow these instructions in reverse order.

4 autre(s) ont terminé cette réparation.

Cameron Weinberg

Membre depuis le 12/04/2011

498 Réputation

6 tutoriels rédigés

Équipe

Cal Poly, Team 18-21, Garner Spring 2011 Membre de l'équipe Cal Poly, Team 18-21, Garner Spring 2011

CPSU-GARNER-S11S18G21

3 membres

7 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 2

30 derniers jours : 12

Total : 5,571