Réparez vos affaires Communauté Boutique

Palm Treo 650 LCD Screen Replacement

Rédigé par : cgood (et 9 autres contributeurs)
  • Commentaires : 0
  • Favoris : 3
  • Réparations terminées : 3

Difficulté

Modérée

Étapes

11

Temps nécessaire

15 minutes

Sections

4

Drapeaux

3

Inconsistent Images

Images incohérentes

Actualiser les images pour les adapter aux conditions préalables augmenterait la qualité de ce tutoriel.

Incorrect Tools

Outils incorrects

Participez à l'amélioration de ce tutoriel en utilisant les outils adaptés dans les photos et/ou le texte.

Better Introduction

Meilleure introduction

Améliorez ce tutoriel en complétant ou modifiant l'introduction.

Introduction

This is a repair guide to access and replace the LCD screen.

  1. Position the phone so the screen faces down.

    • Position the phone so the screen faces down.

    • Remove the stylus found on the back of the phone.

    Modifier

  2. To remove the battery cover, hold down the button in the middle of the phone's back.

    • To remove the battery cover, hold down the button in the middle of the phone's back.

    • Slide the cover down to remove it, and set the cover aside.

    Modifier

  3. Lift the edge of the battery, separating contact points, and pull out as pictured. Lift the edge of the battery, separating contact points, and pull out as pictured.

    • Lift the edge of the battery, separating contact points, and pull out as pictured.

    Modifier

  4. Remove the round rubber cover on the back of the phone located immediately below the antenna.

    • Remove the round rubber cover on the back of the phone located immediately below the antenna.

    • This will uncover a screw that will be removed in the next step.

    Modifier

  6. Remove the six 6.9 mm screws as pictured with a T5 Torx screwdriver. Remove the single 9.8 mm screw next to the antenna on the back plate using a Phillips #00 screwdriver.

    • Remove the six 6.9 mm screws as pictured with a T5 Torx screwdriver.

    • Remove the single 9.8 mm screw next to the antenna on the back plate using a Phillips #00 screwdriver.

    Modifier

  7. Remove the antenna.

    • Remove the antenna.

    Modifier

  8. Pry the back cover off using an iFixIt opening tool. The back cover is attached by several small clips on the inside.

    • Pry the back cover off using an iFixIt opening tool.

    • The back cover is attached by several small clips on the inside.

    Modifier

  9. Disconnect the ribbon cable before removing the motherboard. Unclip the gray tab. Pull out the orange ribbon cable.

    • Disconnect the ribbon cable before removing the motherboard.

    • Unclip the gray tab.

    • Pull out the orange ribbon cable.

    Modifier

  10. Pull off the motherboard. Pull off the motherboard.

    • Pull off the motherboard.

    Modifier

  11. Lift up the LCD screen so that the ribbon strip connecting it to the motherboard can be accessed. Only lift the screen high enough to access the ribbon cable. Only lift the screen high enough to access the ribbon cable.

    • Lift up the LCD screen so that the ribbon strip connecting it to the motherboard can be accessed.

    • Only lift the screen high enough to access the ribbon cable.

    Modifier

  12. Unclip the gray tab. Pull out the orange ribbon strip.

    • Unclip the gray tab.

    • Pull out the orange ribbon strip.

    • Remove the LCD screen.

    Modifier
Conclusion

To reassemble your device, follow these instructions in reverse order.

3 autres ont terminé cette réparation.

Auteur

avec 9 autres contributeurs

cgood

Membre depuis le 28/10/2009

122 Réputation

7 tutoriels rédigés

Badges: 10

+ 7 badges supplémentaires

Équipe

Cal Poly, Team 19-3, Maness Fall 2009 Membre de l'équipe Cal Poly, Team 19-3, Maness Fall 2009

CPSU-MANESS-F09S19G3

4 membres

18 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 0

7 derniers jours : 1

30 derniers jours : 1

Total : 4,996