/
DE
Deutsch
ES
Español
IT
Italiano
PT
Português
TR
Türkçe
JP
日本語
EN
English
FR
Français
NL
Nederlands
RU
Pусский
ZH
中文
KO
한국어
S'inscrire
Connexion
Rejoignez la plus grande communauté de réparation au monde
Pièces
TutorielsRéponses
Modifier
Razer DeathAdder Chroma USB Cable Replacement

Razer DeathAdder Chroma USB Cable Replacement

Henry Shi

Henry Shi et 2 autres contributeurs

Dernière mise à jour le May 17, 2017

6 minutes
Facile

Introduction

Passez à l'étape 1

The Razer DeathAdder Chroma may experience critical issues related to the device not being registered by the computer via a fault in the USB cable.

Ce dont vous avez besoin

Outils

  • Phillips #0 Screwdriver
    Phillips #0 Screwdriver
  • Phillips #000 Screwdriver
    Phillips #000 Screwdriver
  • Spudger
    Spudger

Afficher plus…

  1. Razer DeathAdder Chroma USB Cable Replacement, Outer Casing: étape 1, image 1 de 1

    • Opening the mouse casing will void any warranty that exists for the mouse.

    • Turn the mouse over so the bottom is facing up.

    Modifier

  2. Razer DeathAdder Chroma USB Cable Replacement: étape 2, image 1 de 2 Razer DeathAdder Chroma USB Cable Replacement: étape 2, image 2 de 2

    • Use the blunt end of the spudger to pry the adhesive rubber pads from the top left and right edges.

    Modifier

  3. Razer DeathAdder Chroma USB Cable Replacement: étape 3, image 1 de 2 Razer DeathAdder Chroma USB Cable Replacement: étape 3, image 2 de 2

    • Use a Phillips #0 screwdriver to remove two 6.7 mm screws.

    Modifier

  4. Razer DeathAdder Chroma USB Cable Replacement: étape 4, image 1 de 1

    • Use your fingers to identify the location of the screw under the bottom label.

    Modifier

  5. Razer DeathAdder Chroma USB Cable Replacement: étape 5, image 1 de 1

    • Use a Phillips #0 screwdriver to remove one 6.7 mm screw.

    • Clear the label away from around the screw for easier removal.

    Modifier

  7. Razer DeathAdder Chroma USB Cable Replacement: étape 6, image 1 de 3 Razer DeathAdder Chroma USB Cable Replacement: étape 6, image 2 de 3 Razer DeathAdder Chroma USB Cable Replacement: étape 6, image 3 de 3

    • Turn the mouse over so the bottom is facing down.

    • Separate the top casing from the bottom base by pulling the top casing upwards.

    • Separating the casing too quickly could damage the ribbon connector between the motherboard and the LED lights.

    Modifier

  8. Razer DeathAdder Chroma USB Cable Replacement: étape 7, image 1 de 2 Razer DeathAdder Chroma USB Cable Replacement: étape 7, image 2 de 2

    • Disconnect the ribbon connector between the motherboard and the LED lights by pulling upward.

    • Pulling too hard could damage the wire connections.

    Modifier

  9. Razer DeathAdder Chroma USB Cable Replacement, Motherboard: étape 8, image 1 de 2 Razer DeathAdder Chroma USB Cable Replacement, Motherboard: étape 8, image 2 de 2

    • Disconnect the ribbon connector between the motherboard and the USB cable by pulling upward.

    Modifier

    There are 2 tiny locking pins at the back you may need to spudge the connector casing a bit on each side to release these , I did.

    John bayley - Réponse

  10. Razer DeathAdder Chroma USB Cable Replacement: étape 9, image 1 de 1

    • Use a Phillips #0 screwdriver to remove three 5.5 mm screws.

    Modifier

  11. Razer DeathAdder Chroma USB Cable Replacement: étape 10, image 1 de 2 Razer DeathAdder Chroma USB Cable Replacement: étape 10, image 2 de 2

    • Use a Phillips #0 screwdriver to remove two 11.5 mm screws on the side buttons.

    Modifier

  12. Razer DeathAdder Chroma USB Cable Replacement: étape 11, image 1 de 1

    • Use a Phillips #000 screwdriver to remove one 5.0 mm screw.

    Modifier

    Does anyone know what the circuitry this screw holds in place does, I completely missed this tiny screw and accidently snapped the 2 soldered components off named D2 & D3… But the mouse still works fine ?? however i do not use razer synapse anymore so i dont know if its 100% working

    woolstarr - Réponse

    Never mind it just came to my attention there is a set of LEDs in the mouse wheel which is what that tiny board is, soo …. RIP Mouse Wheel LEDs

    woolstarr - Réponse

  13. Razer DeathAdder Chroma USB Cable Replacement: étape 12, image 1 de 2 Razer DeathAdder Chroma USB Cable Replacement: étape 12, image 2 de 2

    • Disconnect the ribbon connector between the motherboard and the optical sensor.

    Modifier

  14. Razer DeathAdder Chroma USB Cable Replacement: étape 13, image 1 de 2 Razer DeathAdder Chroma USB Cable Replacement: étape 13, image 2 de 2

    • Remove the motherboard by grasping the sides and gently pulling upward.

    Modifier

  15. Razer DeathAdder Chroma USB Cable Replacement, USB Cable: étape 14, image 1 de 1

    • Locate the USB cable.

    Modifier

  16. Razer DeathAdder Chroma USB Cable Replacement: étape 15, image 1 de 2 Razer DeathAdder Chroma USB Cable Replacement: étape 15, image 2 de 2

    • Remove the USB cable by pulling it up and out.

    Modifier
Conclusion

To reassemble your device, follow these instructions in reverse order.

8 autres ont terminé cette réparation.

Auteur

avec 2 autres contributeurs

Henry Shi

Membre depuis le 03/26/17

236 Réputation

1 tutoriel rédigé

Badges: 7

+ 4 badges supplémentaires

Équipe

Baylor, Team S5-G2, Williams Spring 2017 Membre de l'équipe Baylor, Team S5-G2, Williams Spring 2017

BU-WILLIAMS-S17S5G2

3 membres

6 tutoriels rédigés

5 commentaires de tutoriel

Thank you! It realy worked. Btw: The cable for the Deathadder 2013 is working for the Chroma and Elite as well. I Just tried it :)

Pokefreeks - Réponse

Thanks for the advice

João Costa Santos -

Great and easy guide thanx alot, saved me a new mouse :)

jesperkb - Réponse

Is there a reliable website where I can get a replacement cable with low delivery time?

Bubbles EXE - Réponse

where can i get the cable from?

Mourya Singham - Réponse

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 1

7 derniers jours : 4

30 derniers jours : 25

Total : 14,738