Introduction

We will explain the steps needed in order to replace a LCD screen.

Slide the battery cover in the direction the arrow points.
  • Slide the battery cover in the direction the arrow points.

  • Pull the battery cover towards you.

Ajouter un commentaire

Flick the blue switch for the battery to pop out.
  • Flick the blue switch for the battery to pop out.

  • Remove the battery from the camera.

Ajouter un commentaire

  • Using the Phillips #00 Screwdriver, remove the two screws from the caution panel.

  • Remove that panel.

  • Careful for falling pieces.

Ajouter un commentaire

  • Remove the screw with a Phillips #00 Screwdriver from the right side of the camera (with '3x optical zoom' engraved on the side panel).

  • Remove that panel.

Ajouter un commentaire

  • Remove the screw using the Phillips #00 Screwdriver from the bottom the camera, closest to the back cover.

Ajouter un commentaire

  • Gently remove the back cover.

  • It may be a bit stiff, so use some force to remove it. Proceed with caution.

Ajouter un commentaire

  • Remove the screw using a Phillips #00 Screwdriver on the left side (where the "3x optical zoom" panel use to be).

Ajouter un commentaire

  • Remove the small screw using a Phillips #00 Screwdriver on the bottom of the camera attached to the front cover.

  • Gently remove the front cover.

  • Put a little force to pop off the case. Proceed with caution.

Ajouter un commentaire

  • Flip the black secure locks off. Tweezers may be necessary.

  • Detach the two orange cables.

Ajouter un commentaire

  • Gently pull the lens container out of the camera.

Ajouter un commentaire

  • Remove the black screw using a Phillips #00 Screwdriver on the motherboard.

Ajouter un commentaire

  • Remove the two orange cables on the top of the motherboard with tweezers.

  • Lift the motherboard out of its slot.

Ajouter un commentaire

  • For the AV port, detach the bottom orange cable.

  • For the LCD screen, detach the top orange cable on the right side of the motherboard.

  • For the motherboard, detach all the orange cables.

  • Careful not to damage the red, white, and black wires when lifting the board.

Ajouter un commentaire

  • Verify the orange cables from the motherboard are removed from the LCD screen.

  • Lift the LCD screen off the hinge.

Ajouter un commentaire

  • Verify that the LCD screen is attached to the chip on the back on the camera.

  • Remove the dial from the back of the camera. It pops right off very easily.

  • Remove the screw using a Phillips #00 Screwdriver from the camera.

Ajouter un commentaire

  • Remove the orange cable that is attached between the top of the camera and the chip. It should slide straight out with a little bit of force.

  • Remove the chip and the LCD screen now from the camera.

  • The chip may need a slight upward tug with a fingernail or tweezer.

Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

2 autre(s) ont terminé cette réparation.

Eddie Lo

Membre depuis le 11/10/2010

218 Réputation

4 tutoriels rédigés

Équipe

Cal Poly, Team 9-20, Regan Fall 2010 Membre de l'équipe Cal Poly, Team 9-20, Regan Fall 2010

CPSU-REGAN-F10S9G20

5 membres

9 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 2

7 derniers jours : 8

30 derniers jours : 30

Total : 12,802