Pièces

Aucune pièce nécessaire.

  1. Unlatch the battery by pushing outward on both latches.
    • Unlatch the battery by pushing outward on both latches.

    Ajouter un commentaire

  2. Slide battery out.
    • Slide battery out.

    Ajouter un commentaire

    • Remove the five "F2" screws with a Phillips #0 screwdriver.

    Ajouter un commentaire

    • Insert the plastic opening tool above the F1 key.

    • Apply upward pressure until the black plastic strip snaps off. The entire strip will easily come off from left to right.

    Ajouter un commentaire

    • Find the screws above the F1 and INS keys.

    • Unscrew both screws with a Phillips #0 screwdriver.

    Ajouter un commentaire

    • Slowly lift the top edge of the keyboard out with your fingers.

    • The ribbon cable located on the back of the keyboard will become accessible.

    Ajouter un commentaire

    • Locate the black ribbon cable flap.

    • Detach flap with plastic opening tool. The ribbon cable will become free.

    Ajouter un commentaire

    • Your keyboard has now been successfully removed.

    Ajouter un commentaire

    • Remove the back panel by removing the three labeled screws with a Phillips #0 screwdriver.

    Ajouter un commentaire

    • Locate and remove the circled screw with a Phillips #0 screwdriver.

    Ajouter un commentaire

    • Use the plastic opening tool to pry the CD/DVD drive out of the frame.

    Ajouter un commentaire

    • Gently remove the CD/DVD drive from the laptop body.

    Ajouter un commentaire

    • Remove the circled screws with Phillips #0 screwdriver.

    Ajouter un commentaire

    • Remove these screws from the underside of the laptop with Phillips #0 screwdriver.

    Ajouter un commentaire

    • Disconnect the three circled antennas by lightly pulling upward with your fingers. They should detach easily.

    • Note: Yours may only have two (2) antennas. Pay attention to the Orientation of the Aluminum bracket with the pads for reinstallation.

    Ajouter un commentaire

    • Remove the circled screw with a Phillips #0 screwdriver.

    Ajouter un commentaire

    • Detach the 3 marked cables by pulling them out with you fingers as shown.

    • This may require some force. They do not come out easily.

    Ajouter un commentaire

    • Detach the four blue ribbon cables carefully with tweezers. Some of the ribbons may require a flap to be raised because it secures the ribbon in.

    Ajouter un commentaire

    • Remove the top plastic cover by lifting upward from the bottom left-hand corner as shown. The cover will come off easily.

    Ajouter un commentaire

    • Remove the circled motherboard screws with a Phillips #0 Scewdriver.

    • Disconnect this ribbon cable.

    Ajouter un commentaire

    • Remove these screws with a Phillips #0 screwdriver.

    Ajouter un commentaire

    • Detach the display cable by gently pulling it out with your fingers.

    Ajouter un commentaire

    • Remove the motherboard from the left side by gently lifting the left side upward.

    • The boxed volume control may snag on the laptop frame when pulling the motherboard out.

    Ajouter un commentaire

    • The motherboard has now been removed from laptop.

    Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

3 autre(s) ont terminé cette réparation.

Michael Jensen

Membre depuis le 18/04/2011

417 Réputation

6 tutoriels rédigés

Équipe

Cal Poly, Team 4-3, Regan Spring 2011 Membre de l'équipe Cal Poly, Team 4-3, Regan Spring 2011

CPSU-REGAN-S11S4G3

5 membres

6 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 1

30 derniers jours : 5

Total : 11,259