Introduction

This guide will show how the speaker of the UE Boom 2 is removed. This is an extensive and intrusive process which removes most components of the speaker.

Remove the D-ring located at the bottom of the device, opposite end of the power button.
  • Remove the D-ring located at the bottom of the device, opposite end of the power button.

  • Remove by twisting in a counter-clockwise motion.

  • Removing the D-ring will allow you to be able to remove the rubber port cover revealing the headphone jack and charging port.

Ajouter un commentaire

Remove the rubber stripping using a metal spudger.
  • Remove the rubber stripping using a metal spudger.

  • Work around the edge of the rubber stripping slowly prying up the edge.

Ajouter un commentaire

  • Continue removing the rubber stripping down the side.

Ajouter un commentaire

  • On the bottom, unscrew the four 15mm Phillips Head #2 screws, using the Phillips Head #2 screwdriver.

  • Pry up at the location marked, and remove the plastic end cap.

  • Repeat these steps on the top of the speaker.

Ajouter un commentaire

  • Carefully un-loop the cable and unplug from motherboard.

  • Pull out the battery, and handle with care.

Ajouter un commentaire

  • Using the metal spudger, pry up the plastic tab on the inside.

  • Pry up around the entire inside circumference.

  • Repeat on the other end.

Ajouter un commentaire

  • Using the metal spudger tool, pry up the inside edge of the mesh lining.

  • Working down the strip on both sides. Careful as to not rip the mesh.

Ajouter un commentaire

  • Unscrew the two 5mm Phillips Head #1 screws, using a Phillips Head #1 screwdriver.

  • Using the metal spudger, pry open the edge of the cover.

Ajouter un commentaire

  • Using the metal spudger, pry the plastic casing up.

  • Repeat on the other side of the speaker.

Ajouter un commentaire

  • Pull each cover off.

Ajouter un commentaire

  • Using the metal spudger, specifically the pointy end, find the gap between the speaker and billow (the large speaker-like object next to the speaker).

  • Pry the metal wire up and out at exactly this gap, then slide down wire towards one end to pop it out completely.

  • Once one end is out, use fingers to gently pull off completely, so as not to bend the wire to aggressively.

Ajouter un commentaire

  • Repeat previous process for other side of the speaker and billow.

Ajouter un commentaire

  • Using the metal spudger, work it under the billow (circled).

  • Work the billow up around all edges, and pull out of casing.

Ajouter un commentaire

  • With the billow removed, pry up the pink rubber seal with the metal spudger, and remove.

  • Do not use excessive force with the metal spudger, doing so may damage the seal.

Ajouter un commentaire

  • Now, begin to use the same technique for the speaker.

  • Be sure to remove the speaker slowly, as there is a cable attaching the speaker to the motherboard.

Ajouter un commentaire

  • Once speaker is detached from casing, remove cable from motherboard.

  • Connect new speaker by attaching the cable to the same place where the old speaker was just taken out of.

  • If both speakers are blown out, repeat steps 14-16 on the other side.

Where can I found a speaker?

to change it

Zaher - Réponse

Conclusion

To reassemble your device, follow these instructions in reverse order.

2 autre(s) ont terminé cette réparation.

Keegan Divine

Membre depuis le 18/01/2018

325 Réputation

2 tutoriels rédigés

Équipe

Cal Poly, Team S12-G5, Banghart Winter 2018 Membre de l'équipe Cal Poly, Team S12-G5, Banghart Winter 2018

CPSU-BANGHART-W18S12G5

3 membres

13 tutoriels rédigés

Hi, very good tutorial, you got your 30 points ! ;)

But the main question remains to me : where to get a new speaker as UE doen’t sell spare parts and I don’t find any replacement on internet … any help more than welcome …

Cheers!

Francois ORSERO - Réponse

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 7

7 derniers jours : 34

30 derniers jours : 179

Total : 756