Réparez vos affaires

Droit à la réparation

Boutique

the Nokia 6230b Camera Replacement

Rédigé par : Job Jao (et 4 autres contributeurs)
  • Commentaires : 0
  • Favoris : 1
  • Réparations terminées : 2

Difficulté

Modérée

Étapes

16

Temps nécessaire

5 minutes

Sections

4

Drapeaux

1

Missing Prerequisites

Conditions préalables manquantes

Ce tutoriel ne donne pas d'informations sur le début de la procédure. Créez un tutoriel prérequis !

Introduction

The camera is attached to the motherboard in your phone. A T6 screwdriver is needed to access the camera.

Outils

Acheter ces outils

Pièces

Aucune pièce spécifiée.

  1. Press down the button on the back panel.

    • Press down the button on the back panel.

    Traduire

  2. Push the back cover upwards. Push the back cover upwards.

    • Push the back cover upwards.

    Traduire

  3. Remove the back cover from the phone. Remove the back cover from the phone.

    • Remove the back cover from the phone.

    Traduire

  4. Press the silver button on the top of the phone.

    • Press the silver button on the top of the phone.

    Traduire

  5. Slide your thumbnail down the case seam to separate the rest of the case.

    • Slide your thumbnail down the case seam to separate the rest of the case.

    Traduire

  6. Gently, remove the case.

    • Gently, remove the case.

    • Careful! Do not bend the plastic tabs.

    Traduire

  8. Using a T6 Torx Screwdriver, unscrew and remove the six screws shown in the picture. Using a T6 Torx Screwdriver, unscrew and remove the six screws shown in the picture.

    • Using a T6 Torx Screwdriver, unscrew and remove the six screws shown in the picture.

    Traduire

  9. Remove the panel that covers the motherboard. If replacing the speaker, stop at this step and skip forward to the first step of the speaker guide.

    • Remove the panel that covers the motherboard.

    • If replacing the speaker, stop at this step and skip forward to the first step of the speaker guide.

    Traduire

  10. Remove the LCD screen frame.

    • Remove the LCD screen frame.

    Traduire

  11. Remove the motherboard.

    • Remove the motherboard.

    Traduire

  12. Locate the camera on the circuit board.

    • Locate the camera on the circuit board.

    Traduire

  13. Place the circuit board on a firm, static free surface (no cloth/carpet).

    • Place the circuit board on a firm, static free surface (no cloth/carpet).

    • NOTE: The circled alignment notch points to the left.

    Traduire

  14. Pull the left holding tabs to the left.

    • Pull the left holding tabs to the left.

    Traduire

  15. Lift out the left side of the camera.

    • Lift out the left side of the camera.

    Traduire

  16. Pull the right holding tabs to the right.

    • Pull the right holding tabs to the right.

    Traduire

  17. Pull camera off of board.

    • Pull camera off of board.

    Traduire
Conclusion

To reassemble your device, follow these instructions in reverse order.

2 autre(s) ont terminé cette réparation.

Auteur

avec 4 autres contributeurs

Job Jao

Membre depuis le 08/10/2010

37 Réputation

2 tutoriels rédigés

Badges: 6

+ 3 badges supplémentaires

Équipe

Cal Poly, Team 3-27, Regan Fall 2010 Membre de l'équipe Cal Poly, Team 3-27, Regan Fall 2010

CPSU-REGAN-F10S3G27

4 membres

9 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Ajouter un commentaire

Afficher les statistiques:

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 2

Total : 1,795