Introduction

Use this guide to correctly apply replacement battery adhesive strips in your iPhone 5s, 5c, or SE. Any time you remove the battery, these strips must be replaced. The strips are easily damaged if not applied correctly, so you may want to have a spare set of strips on hand if following this guide for the first time.

Before you begin, you should have removed the battery by following a guide like the ones linked below. Note: iPhone 5 and earlier models do not use any adhesive strips.

If you need to replace the battery adhesive strips in a different model iPhone, use one of the following guides:

Before installing new adhesive strips, temporarily connect your new battery and check its alignment in the iPhone.
  • Before installing new adhesive strips, temporarily connect your new battery and check its alignment in the iPhone.

  • If everything looks good, disconnect the battery and remove it.

Ajouter un commentaire

Peel off the large blue film liner and remove it from the adhesive strips completely. Take care not to accidentally touch the adhesive strips after this step. The adhesive is good for one use. If it sticks to your finger or another surface accidentally, it must be discarded and replaced. The blue film sometimes has a defect that prevents it from peeling off, and the strips have to be discarded and replaced.
  • Peel off the large blue film liner and remove it from the adhesive strips completely.

  • Take care not to accidentally touch the adhesive strips after this step. The adhesive is good for one use. If it sticks to your finger or another surface accidentally, it must be discarded and replaced.

  • The blue film sometimes has a defect that prevents it from peeling off, and the strips have to be discarded and replaced.

    • If this happens to you and you got your strips from iFixit, contact us here and we'll send you a replacement on the double.

    • In the meantime, you can temporarily reassemble your iPhone with a bit of double-sided tape to hold the battery.

Ajouter un commentaire

With the exposed adhesive facing down, fold the black tab up at a 90° angle. With the exposed adhesive facing down, fold the black tab up at a 90° angle.
  • With the exposed adhesive facing down, fold the black tab up at a 90° angle.

Ajouter un commentaire

With the exposed adhesive facing down, carefully align the strips into your iPhone's rear case, with the black tab positioned against the lower components (speaker, headphone jack, and Lightning port). Set the adhesive strips into the rear case and allow them to stick. Set the adhesive strips into the rear case and allow them to stick.
  • With the exposed adhesive facing down, carefully align the strips into your iPhone's rear case, with the black tab positioned against the lower components (speaker, headphone jack, and Lightning port).

  • Set the adhesive strips into the rear case and allow them to stick.

Should have mentioned to leave a 1/16” gap at bottom so there's room to fold adhesive removal tab back down, mine so tight no room to fold back ,Hope it goes back together again !

Wayne Camarano - Réponse

Press down on each strip to fully adhere it to the rear case, starting from the middle and working outward towards each end. Press down on each strip to fully adhere it to the rear case, starting from the middle and working outward towards each end. Press down on each strip to fully adhere it to the rear case, starting from the middle and working outward towards each end.
  • Press down on each strip to fully adhere it to the rear case, starting from the middle and working outward towards each end.

Ajouter un commentaire

Peel away the large pink film liner and remove it completely. Peel away the large pink film liner and remove it completely. Peel away the large pink film liner and remove it completely.
  • Peel away the large pink film liner and remove it completely.

Ajouter un commentaire

Without sticking the battery down, lower its connector into the iPhone and align it to its socket on the logic board. Connect the battery. Connect the battery.
  • Without sticking the battery down, lower its connector into the iPhone and align it to its socket on the logic board.

  • Connect the battery.

Ajouter un commentaire

Carefully position the battery and set it into the iPhone. Once the battery sticks, you can't reposition or remove it without destroying the adhesive strips and starting over.
  • Carefully position the battery and set it into the iPhone.

    • Once the battery sticks, you can't reposition or remove it without destroying the adhesive strips and starting over.

Be sure to set the battery closely towards to top of the phone to leave space to fold the black tap of the adhesive tape at the bottom.

Christian Jensen - Réponse

Press the battery firmly into place. Press the battery firmly into place.
  • Press the battery firmly into place.

Ajouter un commentaire

Use the flat end of your spudger or blunt tweezers to fold the black tab downward, tucking it between the lower edge of the battery and the components lining the bottom edge of the iPhone. Be extremely careful not to poke the battery with any sharp tools during this step.  Accidentally puncturing a lithium-ion battery can cause a dangerous fire. Be extremely careful not to poke the battery with any sharp tools during this step.  Accidentally puncturing a lithium-ion battery can cause a dangerous fire.
  • Use the flat end of your spudger or blunt tweezers to fold the black tab downward, tucking it between the lower edge of the battery and the components lining the bottom edge of the iPhone.

  • Be extremely careful not to poke the battery with any sharp tools during this step. Accidentally puncturing a lithium-ion battery can cause a dangerous fire.

Ajouter un commentaire

Be sure to disconnect the battery again before reassembling your iPhone.
  • Be sure to disconnect the battery again before reassembling your iPhone.

    • Working on your phone with the battery connected can destroy sensitive components.

Ajouter un commentaire

Conclusion

To reassemble your iPhone, return to the guide you used to remove the battery and follow the steps in reverse order.

15 autre(s) ont terminé cette réparation.

Jeff Suovanen

Membre depuis le 06/08/2013

160 565 Réputation

408 tutoriels rédigés

Équipe

iFixit Membre de l'équipe iFixit

Community

114 membres

5 894 tutoriels rédigés

Call me crazy, but can’t I just use a thin strip of blu-tack?

domarius - Réponse

Maybe, but the adhesive strips are designed to be very strong and very thin, and reasonably heat-resistant. This keeps the battery secure even if you shake the phone (or take it jogging), and it won’t come loose if the phone gets hot. The thin profile also means the battery has room to expand slightly without contacting or putting pressure on the display. Considering how cheap the strips are vs. the cost of the expensive phone you are repairing, I tend to err in favor of putting it back together the way it’s designed. But, your phone, your choice!

Jeff Suovanen -

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 43

7 derniers jours : 350

30 derniers jours : 1,628

Total : 2,670