Réparez vos affaires Communauté Boutique

Google Pixel 5 Screen Replacement

En vedette

Rédigé par : Robert Boyd (et 5 autres contributeurs)
  • Commentaires : 16
  • Favoris : 2
  • Réparations terminées : 12

Tutoriel vedette

Difficulté

Modérée

Étapes

12

Temps nécessaire

30 minutes - 1 heure

Sections

1

Drapeaux

1

Featured Guide

Tutoriel vedette

L'équipe iFixit trouve ce tutoriel particulièrement réussi.

Introduction

Follow this guide to replace a broken or cracked screen on a Google Pixel 5.

Unlike previous Google Pixels models, the Pixel 5’s screen is reinforced with a metal frame. The earpiece speaker is also glued onto the back side of the screen.

  1. Heat an iOpener and apply it to the bottom edge of the screen for one minute.

    • Heat an iOpener and apply it to the bottom edge of the screen for one minute.

    • A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the phone—the display and internal battery are both susceptible to heat damage.

    Traduire

  2. Apply a suction cup to the screen, as close to the heated edge as possible. If your screen is badly cracked, follow this guide to tape over the cracked screen. If all else fails, you can superglue the suction cup to the broken screen. Pull up on the suction cup with strong, steady force to create a gap.

    • Apply a suction cup to the screen, as close to the heated edge as possible.

    • If your screen is badly cracked, follow this guide to tape over the cracked screen. If all else fails, you can superglue the suction cup to the broken screen.

    • Pull up on the suction cup with strong, steady force to create a gap.

    • Depending on the age of your device, this may be difficult. If you have trouble, apply more heat and try again.

    • Insert the opening pick into the gap.

    Traduire

  3. Slide the opening pick back and forth along the bottom of the screen to slice the adhesive. Leave the pick inserted in the bottom right corner to prevent the adhesive from re-sealing. Leave the pick inserted in the bottom right corner to prevent the adhesive from re-sealing.

    • Slide the opening pick back and forth along the bottom of the screen to slice the adhesive.

    • Leave the pick inserted in the bottom right corner to prevent the adhesive from re-sealing.

    Traduire

  4. Apply a heated iOpener to the left edge of the screen for one minute.

    • Apply a heated iOpener to the left edge of the screen for one minute.

    Traduire

  6. Insert another opening pick into the bottom left corner of the screen. Slide the opening pick around the left corner. Do not insert the pick more than 1/4 inch (6 mm) or you may damage the screen's flex cable located in the middle of the left edge.

    • Insert another opening pick into the bottom left corner of the screen.

    • Slide the opening pick around the left corner.

    • Do not insert the pick more than 1/4 inch (6 mm) or you may damage the screen's flex cable located in the middle of the left edge.

    • Continue to slide the pick up towards the front camera to slice the adhesive on the left edge of the screen.

    • Leave the pick inserted to prevent the adhesive from re-sealing.

    Traduire

  7. Insert another opening pick into the top left corner of the screen. Slide the pick around the front camera and across the top edge of the phone. If the adhesive is difficult to slice, apply heat to the area for one minute and try again.

    • Insert another opening pick into the top left corner of the screen.

    • Slide the pick around the front camera and across the top edge of the phone.

    • If the adhesive is difficult to slice, apply heat to the area for one minute and try again.

    • Slide the pick to the top right corner of the phone and leave the pick inserted.

    Traduire

  8. Insert an opening pick into the bottom right corner of the screen. Slide the pick up to the top right corner to slice the last edge of adhesive. You may need to run an opening pick around the edges again to ensure all the adhesive is cut. It is applied the thickest on the four corners.

    • Insert an opening pick into the bottom right corner of the screen.

    • Slide the pick up to the top right corner to slice the last edge of adhesive.

    • You may need to run an opening pick around the edges again to ensure all the adhesive is cut. It is applied the thickest on the four corners.

    Traduire

  9. Use the opening pick from the top left corner to lift up the left edge of the screen a few millimeters. This will keep the clips from snapping back down into the case. Lift up on the right side of the screen and open up the phone like a book.

    • Use the opening pick from the top left corner to lift up the left edge of the screen a few millimeters. This will keep the clips from snapping back down into the case.

    • Lift up on the right side of the screen and open up the phone like a book.

    • Do not open the screen more than 90 degrees to prevent damaging the screen flex cable.

    Traduire

  10. Use tweezers to grip the screen connector cover securing the screen flex cable. Push the clip in towards the connector to unlatch it.

    • Use tweezers to grip the screen connector cover securing the screen flex cable.

    • Push the clip in towards the connector to unlatch it.

    Traduire

  11. Remove the screen connector cover. Remove the screen connector cover.

    • Remove the screen connector cover.

    Traduire

  12. Use the tip of the spudger to pry up and disconnect the screen flex cable. To re-attach press connectors like this one, carefully align and press down on one side until it clicks into place, then repeat on the other side. Do not press down on the middle. If the connector is misaligned, the pins can bend, causing permanent damage

    • Use the tip of the spudger to pry up and disconnect the screen flex cable.

    • To re-attach press connectors like this one, carefully align and press down on one side until it clicks into place, then repeat on the other side. Do not press down on the middle. If the connector is misaligned, the pins can bend, causing permanent damage

    Traduire

  13. Remove the screen. Use tweezers to pick off the remaining adhesive on the case.

    • Remove the screen.

    • Use tweezers to pick off the remaining adhesive on the case.

    • Be sure to test your repairs before you affix the screen with new adhesive.

    • If you are using a custom-cut adhesive, follow this guide for instructions on how to apply adhesive to the replacement screen.

    • If you are using Tesa tape to reattach the screen, follow this guide.

    Traduire

    Where from we can buy the screen. Thanks

    Ajay Sharma - Réponse

Conclusion

Compare your new replacement part to the original part—you may need to transfer remaining components or remove adhesive backings from the new part before installing.

To reassemble your device, follow the above steps in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Answers community for help.

12 autres ont terminé cette réparation.

Auteur

avec 5 autres contributeurs

Robert Boyd

Membre depuis le 01/02/2021

14 738 Réputation

87 tutoriels rédigés

Badges: 19

+ 16 badges supplémentaires

Équipe

iFixit Membre de l'équipe iFixit

Community

145 membres

17 086 tutoriels rédigés

15 commentaires

if i want only screen (lcd display) of pixel 5 from where can i get the screen. sudhri@gmail.com my mail address

Digvijay Engineers - Réponse

Hello! This tutorial is well explained and seems ok to realize, but the problem i’m facing is to find the right spare part… Once contacted, google assistance said the only option is to send it back to them for 138€ and 7-10 days… Can you recommand a trustworsthy website for that?

Aurelien Malot - Réponse

Usually i look on amazon (sent by amazon) to get the warranty if i got any problem.

Daniele Carminati -

Check out the iFixit store. We stock some parts for the Pixel 5, including the screen and battery.

Zac Hall -

The screen that I ordered has a cable that runs the wrong way. It would need to be twisted to make it fit my Pixel 5. Any suggestions?

Gordon Stephenson - Réponse

Get a refund and send it back and order a different display.

Josh Cook -

Do order the replacement with or without frame?

Marc H - Réponse

unless you’re a super pro, better with frame, It is not easy to glue up to the frame, and if that frame is damaged or gets damaged during tear down, can be a problem.

Manuel López -

Hi,

I just replaced the screen with a new one, but now I have problems with the proximity sensor, When i press on one side of the screen it works, so I guess it is because it may be not glued strongly wnough? wich glue do you recommend?

Manuel López - Réponse

There is no info here about transferring the speaker. How is that done? Is adhesive needed? If so, what type?

Mike K - Réponse

I just use one or two strips of adhesive tape if I need to use new adhesive. Not much, though. If possible, get the earpiece speaker nice and warm to soften the adhesive. Apply lots of heat to the old display on the touchscreen side, not heating the earpiece directly. If you can heat it up enough, it should come off pretty cleanly. Then warm it up again and seat it well onto the new display with the original adhesive still attached the the earpiece speaker.

Mark Student -

Hello! Just foolishly cracked my Google Pixel 5 screen and have no idea where to get the replacement. Based on your experience, could you please suggest where to order Pixel 5 screen replacement so that it would be as sharp and bright as the original? Ideally – THE original. Thank you in advance!

Taisia Osipova - Réponse

i bought a screen on ebay. supposedly oem. it seems just the same as the original.

Mike K -

Rounded.com expensive but 100% new and original parts straight from manufacturer

Simon -

I have to say I found this to be one of the easiest repairs I've ever done, I bought the complete original screen assembly from rounded.com and the manufacturer adhesive tape which gives the phone its IP rating seal back. Cost me about £160 all in. But I learnt skills at the same time. I used my nails and a guitar plectrum working from bottom end of the phone up. As good as new, well chuffed

Simon - Réponse

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 96

7 derniers jours : 715

30 derniers jours : 3,265

Total : 32,327