Aller au contenu principal
Autosampler Battery Enclosure Assembly (For Old & New Versions)

Autosampler Battery Enclosure Assembly (For Old & New Versions)

Brooke Mason

Brooke Mason et 2 autres contributeurs

Dernière mise à jour le February 27, 2020

2 heures
Modérée
Tutoriel réalisé par la communauté

Ce dont vous avez besoin

iFixit touche une commission lorsque vous achetez par l'intermédiaire de ces liens.
  1. Autosampler Battery Enclosure Assembly (For Old & New Versions), Drill the holes into the enclosure.: étape 1, image 1 de 3 Autosampler Battery Enclosure Assembly (For Old & New Versions), Drill the holes into the enclosure.: étape 1, image 2 de 3 Autosampler Battery Enclosure Assembly (For Old & New Versions), Drill the holes into the enclosure.: étape 1, image 3 de 3
    • 1. Drill a hole in the top right corner 16.5 mm from the top and 30.3 mm from the side using a 13/16 inch drill bit.

    • 2. Drill two holes in the side 30 mm from the short sides and 27 mm from the long side using a 1/2 inch drill bit.

    • 3. Screw in two waterproof cable gland connectors to the side holes.

    • Put in a button in the rocker switch in the other hole.

  2. Autosampler Battery Enclosure Assembly (For Old & New Versions), Prepare the battery wires.: étape 2, image 1 de 2 Autosampler Battery Enclosure Assembly (For Old & New Versions), Prepare the battery wires.: étape 2, image 2 de 2
    • 4. Cut the purple wire and the inline fuse holder wire 10 inches long.

    • 5. Attach a 10A, 12VDC fuse.

  3. Autosampler Battery Enclosure Assembly (For Old & New Versions), Prepare the wires for the batteries.: étape 3, image 1 de 3 Autosampler Battery Enclosure Assembly (For Old & New Versions), Prepare the wires for the batteries.: étape 3, image 2 de 3 Autosampler Battery Enclosure Assembly (For Old & New Versions), Prepare the wires for the batteries.: étape 3, image 3 de 3
    • 6. Strip both wires about 1/2 inch

    • 7. using the 16 gauge slot of the wire stripper

    • 8. Get 3 pink and 3 blue fully insulated heat-shrink quick-disconnect terminals.

  4. Autosampler Battery Enclosure Assembly (For Old & New Versions), Attach heat-shrinking terminals.: étape 4, image 1 de 3 Autosampler Battery Enclosure Assembly (For Old & New Versions), Attach heat-shrinking terminals.: étape 4, image 2 de 3 Autosampler Battery Enclosure Assembly (For Old & New Versions), Attach heat-shrinking terminals.: étape 4, image 3 de 3
    • 9. Crimp the fully insulated heat-shrink quick-disconnect terminal onto the end of the wire.

    • 10. Use the heat shrink gun to heat shrink the ends of the crimps.

    • 11. Repeat for both ends of both wires.

  5. Autosampler Battery Enclosure Assembly (For Old & New Versions), Prepare the battery connector wire.: étape 5, image 1 de 2 Autosampler Battery Enclosure Assembly (For Old & New Versions), Prepare the battery connector wire.: étape 5, image 2 de 2
    • 12. Cut two feet of red and black 16G wire (grey insulated wire) and then strip 2 inches off of the grey insulation.

    • 13. Strip 1/2 inch of both the black and red wires.

  6. Autosampler Battery Enclosure Assembly (For Old & New Versions), Prepare the battery connector wire.: étape 6, image 1 de 3 Autosampler Battery Enclosure Assembly (For Old & New Versions), Prepare the battery connector wire.: étape 6, image 2 de 3 Autosampler Battery Enclosure Assembly (For Old & New Versions), Prepare the battery connector wire.: étape 6, image 3 de 3
    • 14. Place two metal contacts on both the red and black wires.

    • You should see copper wire through the little pin hole. If not, strip more insulation.

    • 15. Crimp the contacts into place.

    • 16. Thread the contacts into the Amphenol connector.

  7. Autosampler Battery Enclosure Assembly (For Old & New Versions), Prepare the battery connector wire.: étape 7, image 1 de 3 Autosampler Battery Enclosure Assembly (For Old & New Versions), Prepare the battery connector wire.: étape 7, image 2 de 3 Autosampler Battery Enclosure Assembly (For Old & New Versions), Prepare the battery connector wire.: étape 7, image 3 de 3
    • 17. Attach the green wedge to the connector.

    • 18. Cut 1.5 inches of 2:1 0.25" diameter heat shrink tubing.

    • 19. Use the heat shrink gun to shrink the heat shrink tubing.

  8. Autosampler Battery Enclosure Assembly (For Old & New Versions), final battery connector.: étape 8, image 1 de 1
    • 20. This is what the final battery connector looks like.

  9. Autosampler Battery Enclosure Assembly (For Old & New Versions), Creating a 2-pin amphenol connector.: étape 9, image 1 de 3 Autosampler Battery Enclosure Assembly (For Old & New Versions), Creating a 2-pin amphenol connector.: étape 9, image 2 de 3 Autosampler Battery Enclosure Assembly (For Old & New Versions), Creating a 2-pin amphenol connector.: étape 9, image 3 de 3
    • 21. Cut 30 inches of red and black 16G wire (grey insulated wire). Strip 2 inches of the grey rubber coating from both ends.

    • 22. Strip 0.5 inches from both the red and black wires from both ends.

    • 23. Obtain a 2-pin amphenol connector.

  10. Autosampler Battery Enclosure Assembly (For Old & New Versions), Creating a 2-pin amphenol connector.: étape 10, image 1 de 3 Autosampler Battery Enclosure Assembly (For Old & New Versions), Creating a 2-pin amphenol connector.: étape 10, image 2 de 3 Autosampler Battery Enclosure Assembly (For Old & New Versions), Creating a 2-pin amphenol connector.: étape 10, image 3 de 3
    • 24. Disconnect the 2-pin amphenol connector into its individual parts.

    • 25. Loosen the screws on the amphenol connector. Thread the stripped wire through the end of the amphenol connector and through the middle piece of the amphenol connector.

    • The black GND wire should be in the “A” port and the red PWR wire should be in the “B” port.

    • 26. Solder the wires to the other end of the amphenol connector.

  11. Autosampler Battery Enclosure Assembly (For Old & New Versions), Creating a 2-pin amphenol connector.: étape 11, image 1 de 3 Autosampler Battery Enclosure Assembly (For Old & New Versions), Creating a 2-pin amphenol connector.: étape 11, image 2 de 3 Autosampler Battery Enclosure Assembly (For Old & New Versions), Creating a 2-pin amphenol connector.: étape 11, image 3 de 3
    • 27. Obtain a Flux Remover Pen, 99 % Isopropyl Alcohol, and a Q-Tip.

    • 28. Use the pen to remove the flux from the soldered pins.

    • 29. Dip the q-tip in the alcohol. Use the q-tip to remove the flux remover.

  12. Autosampler Battery Enclosure Assembly (For Old & New Versions), Creating a 2-pin amphenol connector.: étape 12, image 1 de 3 Autosampler Battery Enclosure Assembly (For Old & New Versions), Creating a 2-pin amphenol connector.: étape 12, image 2 de 3 Autosampler Battery Enclosure Assembly (For Old & New Versions), Creating a 2-pin amphenol connector.: étape 12, image 3 de 3
    • 30. Screw the amphenol pieces back together. Then tighten the external screws.

    • 31. This is what a final 2-pin amphenol connector looks like.

    • 32. Thread the 2-pin amphenol autosampler wire through the top hole and the battery connector wire through the bottom hole of the enclosure box. Leave about a foot of each on the outside of the box. Tighten the glands.

    • Once 2 pin and battery wires constructed and threaded into box, strip opposite ends and add heat-shrinking quick disconnect terminals.

  13. Autosampler Battery Enclosure Assembly (For Old & New Versions), Connecting wires to the rocker switch.: étape 14, image 1 de 3 Autosampler Battery Enclosure Assembly (For Old & New Versions), Connecting wires to the rocker switch.: étape 14, image 2 de 3 Autosampler Battery Enclosure Assembly (For Old & New Versions), Connecting wires to the rocker switch.: étape 14, image 3 de 3
    • 33. This is what the wires look like threaded through the glands in the box.

    • 34. Connect the battery wire to the first two prongs of the rocker switch.

    • 35. Connect the 2-pin amphenol autosampler wire to the last two prongs of the rocker switch.

  14. Autosampler Battery Enclosure Assembly (For Old & New Versions), Connecting the battery in the enclosure.: étape 15, image 1 de 3 Autosampler Battery Enclosure Assembly (For Old & New Versions), Connecting the battery in the enclosure.: étape 15, image 2 de 3 Autosampler Battery Enclosure Assembly (For Old & New Versions), Connecting the battery in the enclosure.: étape 15, image 3 de 3
    • 36. Connect the purple wire and fuse wire to the middle two prongs of the rocker switch.

    • 37. Connect the other side of the purple wire and fuse wire to a 12 volt battery.

    • 38. A light goes on if the fuse is blown!

  15. Autosampler Battery Enclosure Assembly (For Old & New Versions), Completing the enclosure.: étape 16, image 1 de 3 Autosampler Battery Enclosure Assembly (For Old & New Versions), Completing the enclosure.: étape 16, image 2 de 3 Autosampler Battery Enclosure Assembly (For Old & New Versions), Completing the enclosure.: étape 16, image 3 de 3
    • 39. Place the 12V battery and all the wires into the enclosure.

    • 40. Screw the lid onto the enclosure.

    • 41. This is what the completed battery enclosure looks like.

  16. Autosampler Battery Enclosure Assembly (For Old & New Versions), Label the switch: étape 17, image 1 de 1
    • Label the switch with the label maker.

    • <-- Manual Mode

    • --> Node Trigger Mode

Ligne d'arrivée

Une autre personne a terminé cette réparation.

Brooke Mason

Membre depuis le 05/29/19

2 928 Réputation

17 tutoriels rédigés

Équipe

Open-Storm Membre de l'équipe Open-Storm

Community

14 membres

24 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 1

7 derniers jours : 1

30 derniers jours : 2

Total : 215