Il est possible que cette traduction ne reflète pas les dernières mises à jour du tutoriel source. Aidez à mettre à jour la traduction ou bien consultez le tutoriel source.
Introduction
Ce tutoriel de réparation a été rédigé par l'équipe d'iFixit et n'a pas été approuvé par Google. Plus d'infos sur nos tutoriels de réparation ici.
Suivez ce tutoriel pour changer l'écran cassé ou fissuré d'un Google Pixel 5a.
Pour votre sécurité, laissez la batterie se vider en dessous de 25 % avant de vous lancer. Cela réduit les risques de déclencher un incendie dangereux si jamais vous abîmez accidentellement la batterie pendant la réparation. Si votre batterie est gonflée, prenez les précautions nécessaires.
Ce dont vous avez besoin
-
-
Notez les deux jointures sur le bord du téléphone :
-
Jointure de l'écran : cette jointure sépare l'écran du reste du téléphone. Ne faites surtout pas levier ici.
-
Jointure de la bordure : c'est là que la bordure en plastique conçue pour protéger l'écran est fixée au châssis. Elle est maintenue en place par des clips en plastique. C'est là que vous devez faire levier.
-
-
-
Posez un iOpener chauffé sur le bord droit de l'écran pendant une minute pour ramollir l'adhésif.
-
-
-
Prenez note des points d'entrée optimaux avant de continuer.
-
-
-
Positionnez une ventouse aussi près du bord droit de l'écran que possible.
-
Soulevez la ventouse de façon ferme et constante afin de créer un petit interstice entre la bordure et le châssis central.
-
-
-
Insérez la pointe d'un médiator dans la jointure de la bordure à environ 4-5 cm du bas du téléphone.
-
-
-
Outil utilisé dans cette étape :Magnetic Project Mat$19.95
-
Utilisez un tournevis Torx T3 pour retirer la vis de 4,6 mm de long qui maintient le cache du connecteur d'écran.
-
Tout au long de la réparation, gardez la trace de chaque vis et assurez-vous qu'elle retourne exactement là d'où elle vient.
-
-
-
Ôtez le cache du connecteur d'écran à l'aide d'une pincette.
-
-
-
Utilisez la pointe d'une spatule (spudger) pour faire levier et déconnecter la nappe d'écran.
-
Pour réassembler votre appareil, suivez les étapes ci-dessus dans l'ordre inverse.
Déposez vos déchets électroniques dans un centre de recyclage certifié.
La réparation ne s'est pas déroulée comme prévu ? Essayez des solutions de dépannage de baseou demandez de l'aide sur notre Forum.
Comparez votre nouvelle pièce de rechange à la pièce d'origine - il se peut que vous deviez transférer les composants restants ou retirer les dos adhésifs de la nouvelle pièce avant de l'installer.
Pour réassembler votre appareil, suivez les étapes ci-dessus dans l'ordre inverse.
Déposez vos déchets électroniques dans un centre de recyclage certifié.
La réparation ne s'est pas déroulée comme prévu ? Essayez des solutions de dépannage de baseou demandez de l'aide sur notre Forum.
Comparez votre nouvelle pièce de rechange à la pièce d'origine - il se peut que vous deviez transférer les composants restants ou retirer les dos adhésifs de la nouvelle pièce avant de l'installer.
Annulation : je n'ai pas terminé ce tutoriel.
74 autres ont terminé cette réparation.
Merci à ces traducteurs :
96%
Ces traducteurs nous aident réparer le monde ! Vous voulez contribuer ?
Commencez à traduire ›
40 commentaires
Thank you, this was useful for removing the screen from my device without damaging it further! With the invisible fasteners, a guide like this is invaluable for knowing where the latches are and how to get to them.
As a guide for replacing a screen, there are a few other things worth mentioning:
• Is it necessary to remove the old gasket ("adhesive film")?
• How do you apply the new display adhesive, the one that comes on a blue card? Do you need to do that before re-attaching the new screen cable? Why are there cut-outs in the blue card that mostly match the positions of contacts on my device, but not entirely? Do I remove it before closing the device?
• In addition to a couple pieces of tape, the replacement screen also comes with a small piece of film protecting the camera area. Do pull it out by the small red tab before re-assembly.
• Any other tips for reattaching that press-fit board-to-board connector? Should I really expect it to click into place? It took me many tries to get that aligned and secured!
1. Depends on what you mean by "Necessary," but it is recommended
2. In Step 15, there is a guide linked for custom-cut adhesive; follow that one.
Yes, before you reconnect cable.
I don't know what the cutouts are for, but you will remove the blue card anyway after applying the adhesive to the frame. The important part to line up is the adhesive to the frame; the blue card doesn't matter beyond that.
And yes, you will remove it before closing the device.
3. Didn't see that. I hope my device's camera works. I'll check that now.
4. Reconnecting this was the most tedious part for me. I used the gold colored corners on the board to line up the connector(you can see these in the picture for step 15. Also, I used my finger and not the spudger for pressing down when reattaching (and I don't have small hands); this helps you feel the slight click when it's in place.
Also, you can use the suction cup as a sort of kickstand so you have enough ribbon cable to work with (because there's not a lot of it.)
Lol No -
Literally went step by step by this guide and repaired my own Google pixel 5A phone. If you purchase the entire repair kit for the Google Pixel 5A you have essential every tool you'll need. I will recommend ordering screens for this phone here from this website.
Good guide but agree with keturn that it would be great to have more tips and reminders for replacing the screen.
I mostly figured it out, heres how I did it:
- I removed the old adhesive, and tried to scrape and clear it all.
- next I attached the new adhesive before connecting the screen cable since I figured it would be hard when its attached. I did try to make sure to press all along the adhesive with tweezers to set it. I left the next set of backing on to minimize the time the adhesive is exposed (avoid dust or me touching it)
- then I attached the connector. This was a little difficult, but also not very experienced with this.
- then I removed the adhesive backing and closed it up right after. I used rubber bands (3 across and 1 down the middle) to clamp the screen and put some books on it as much as I could over the next day.